Subscribe to Our Youtube Channel
Related Manuals for Me-Mover FIT 2.0
Summary of Contents for Me-Mover FIT 2.0
- Page 1 Me-Mover Fitness FIT 2.0 Designed in Copenhagen QUICK GUIDE for assembly and initial ride ME-MOVER.COM...
- Page 2 BEFORE YOU START PLEASE REGISTER AT: www.me-mover.com/me-mover-fit-registration/ ME-MOVER.COM...
- Page 3 A component that is not approved, or assembly that is not correct can put high stress on your Me-Mover FIT 2.0 or components. A frame, fork, or component with modifications could decrease your control and cause you to fall.
- Page 4 IN THE BOX This is how your Me-Mover FIT 2.0 is packaged in the box. The Me-Mover FIT 2.0 box contains the following pieces and sub-assemblies: 3mm short hex key 4mm long hex key 5mm long hex key 6mm long hex key...
- Page 5 AN OVERVIEW OF THE ME-MOVER FIT 2.0 Handlebars Handlebar stem Brake handles Steering column quick release Inner steerer Steering column Bottle holder (optional) Transmissions Fixtures for Folding accessories Fixture Centre block screw Front fork Locking bolt Rear disc brake Foot strap...
-
Page 6: How To Use The Quick Releases
HOW TO USE THE QUICK RELEASES The Me-Mover FIT 2.0 has two quick releases. It is extremely important that these quick releases are tightened securely before you use your Me-Mover FIT 2.0. Front wheel quick release : used to secure the front wheel to the front fork. - Page 7 TO ASSEMBLE YOUR ME-MOVER FIT 2.0, FOLLOW THESE STEPS: 1. Place the cardboard box on the floor and use this as an underlay during assembly. 2. Open the steering column quick release and pull out the inner steerer from the steering column.
- Page 8 NOTE: The left brake cable loops under the stem from the left hand side. The right brake cable loops under the stem from the right hand side. This ensures the cables are close to the frame; not interfering with the riders knees whilst riding. Stem Inner Steerer Cable loop Bottle Holder fixtures ME-MOVER.COM...
- Page 9 Screw the lock nut and adjustment screw tight. NOTE: Please take note of which cable operates the front and the rear brake when doing this step. There may be local laws regulating how your brakes need to function. Lock nut Adjustment screw Groove ME-MOVER.COM...
- Page 10 JUST close the clamp. Hold the clamp in OPEN position Rotate the nut in clockwise direction WARNING! Always ensure that the front wheel quick release is fastened securely! For detailed instructions refer to “How To Use The Quick Releases” on page 6. ME-MOVER.COM...
- Page 11 10. Connect the steering column to the rear frame. Press the frame in between the flanges at the steering column at a slightly downward angle. Then adjust until the two holes are aligned. Steering column Rear frame Align the holes ME-MOVER.COM...
- Page 12 Steering column and rear frame in aligned position 11. Screw in the steering column screw using a 6mm hex key and then re-insert the safety pin. NOTE: Remember to insert the column screw the same way it came out! Steering column screw Safety pin ME-MOVER.COM...
- Page 13 Brake splitter 13. Attach the foot straps. Align the components as shown, and tighten the screw. NOTE: Please hold the bracket in place with one hand whilst tightening the screw with the other. Foot strap Pedal Screw Washer Bracket ME-MOVER.COM...
- Page 14 14. Mount the mudguard. Place the washers between the mudguard and the front fork as shown. Use a 10mm open-end wrench to hold the nut in place while you rotate the screw with a 5mm hex key. Front fork Washer Screw Washer Mudguard ME-MOVER.COM...
- Page 15 WARNING! Do not use the Me-Mover FIT 2.0 if the brakes do not work properly. If they are not working properly, please refer to the User Manual for instructions on how to adjust the brakes.
- Page 16 QUICK FOLD INSTRUCTION Folding The Me-Mover FIT 2.0 can be folded in seconds to roll it along with you or for easy at-home storage. 1. Lower the steering column to the lowest position. 2. Remove the safety pin. 3. Put one foot on one pedal to prevent the Me-Mover FIT 2.0 from tipping and pull one brake handle.
- Page 17 If you do not hear the ‘CLICK’ sound it means the locking bolt has not been secured in place. If the locking bolt does not click into place, do not use the Me-Mover FIT 2.0 under any circumstance. There should be no space around the locking bolt. Remem- ber to re-insert the safety pin.
-
Page 18: Riding Safely
FITTING THE SAFETY PIN NOTE: when fitting the safety pin, ensure the attached wire loops around the pin as shown below. Do not ride the Me-Mover FIT 2.0 without correctly fitting the safety pin. RIDING SAFELY Always wear a helmet! -
Page 19: Riding Instructions
WARNING! Do not try the Me-Mover FIT 2.0 in a crowded or high-traffic area for the first time. The Me-Mover FIT 2.0 offers a totally unique riding feel that requires only minutes to learn. Follow these simple instructions to start riding your new Me-Mover FIT 2.0. - Page 20 Rotate counter -clockwise pedal axle WARNING! Positioning the ball of your feet behind the pedal axle can cause injury and/or cramp in your calf muscle over time. Make sure the straps are securely tightened. ball of your foot pedal axle ME-MOVER.COM...
- Page 21 6. Stand next to your Me-Mover FIT 2.0. 7. Grab the handlebar and hold ONE brake tight. Place one foot onto the pedal at a time. For the purpose of stability, place your foot closest to the Me-Mover FIT 2.0 on the pedal first.
- Page 22 WARNING! Although you can learn to ride the Me-Mover FIT 2.0 in minutes, do not ride on challenging terrain or in high traffic areas until you are practiced and have 100% control of the Me-Mover FIT 2.0. It is your own responsibility to practice sufficiently on the Me-Mover FIT 2.0 before entering crowded areas.
-
Page 23: Useful Links
Thank you for purchasing a Me-Mover FIT 2.0. We hope you have as much fun on it as we did designing it. We look forward to hearing about your Me-Mover journey. - Page 24 ME-MOVER.COM...
Need help?
Do you have a question about the FIT 2.0 and is the answer not in the manual?
Questions and answers