Table of Contents
Advertisement
Quick Links
CONTENT
I. SAFETY INFORMATION ------------------- 2
II. FEATURES ------------------------------------- 2
IV. CONTROLS ------------------------------------ 4
5.1 Setup Menu ------------------------------- 6
5.3 Printing ------------------------------------12
5.4 Loading Thermal Paper --------------14
--------------------------
--------------------------
-----------------------------
----------------------------
-----------
----------------
Page
3
10
15
16
17
18
Advertisement
Table of Contents
Summary of Contents for CENTER Technology CENTER 500
-
Page 1: Table Of Contents
CONTENT Page I. SAFETY INFORMATION ------------------- 2 II. FEATURES ------------------------------------- 2 ----------- III. GENERAL SPECIFICATIONS IV. CONTROLS ------------------------------------ 4 V. OPERATING INSTRUCTIONS 5.1 Setup Menu ------------------------------- 6 -------------------------- 5.2 Measurement 5.3 Printing ------------------------------------12 5.4 Loading Thermal Paper --------------14 ---------------- 5.5 Battery Replacement VI. -
Page 2: Safety Information
Temperature Recorder SAFETY INFORMATION 1. Read the following safety information carefully before attempting to operate or service the meter. 2. Only qualified personnel should perform repairs or servicing not covered in this manual. 3. Periodically wipe the case with a dry cloth. Do not use abrasives or solvents on these instruments. -
Page 3: General Specifications
Temperature Recorder III. GENERAL SPECIFICATIONS Measurement Range: Type-K -200°C ~ 1370°C -328°F ~ 2498°F Type-J -200°C ~ 760°C -328°F ~ 1400°F Accuracy: -200°C ~ 1370°C ±0.1% + 0.8°C -328°F ~ 2498°F ±0.1% + 1.6°F Resolution: 0.1°C / 0.1°F Sample Rate: 2 times / second Input Protection: 60V DC or 24Vrms AC... -
Page 4: Controls
Temperature Recorder IV. CONTROLS Paper Slot OPEN Paper Output Manual Feed Knob Print Head Level TEMPERATURE RECORDER L C D DC 9V Jack Setup Panel MENU MENU °C °F Function Panel INST FEED Print Panel PRINT Temperature Sensor Input Connector Setup Panel: Function Panel: Exit without saving... -
Page 5: Auto Power Off
Temperature Recorder Slip Proof Rubber MASTER RESET SAZE AA 1.5V X 6 PLEASE READ MANUAL FOR SAFET RANGE : TYPE K 1370 2498 TYPE J 760 C 328 F 1400 F Paper Spec. : Thermal Paper 58 mm Width Diameter Max Battery Cover AC Adaptor ( isolated ) : DC 9V... -
Page 6: Operating Instructions
Temperature Recorder V. OPERATING INSTRUCTIONS 5.1 Setup Menu Press either of the “Browse menu…” (Menu Select) buttons to select menu OPEN TEMPERATURE RECORDER MENU MENU Enter Browse menu or number up Browse menu or number down Exit without saving... -
Page 7: Menu Description
Temperature Recorder Menu item S e t s y s t e m c l o c k S e t T h e r m o c o u p l e S e t s t a r t / s t o p p r i n t p r i n t i m o d... - Page 8 Temperature Recorder Set print start/stop time and print mode Set start time Set start date Set start year Set stop time Set stop date Set stop year Print mode Text mode Text print interval Graph mode Graphic print speed Minimun scale Scale range Note: 1.
- Page 9 Temperature Recorder Datalogger start/stop time and Recording Interval Setup Set start time Set start date Set start year Set stop time Set stop date Set stop year Set record interval Note: 1.Recording interval options: 1/2/5/10/15/30 second; 1/2/5/10/15/30/60 minute 2.When REC setup is done and in normal mode, the LCD will display “TIMED REC”...
-
Page 10: Measurement
Temperature Recorder 5.2 Temperature Measurements OPEN TEMPERATURE RECORDER MENU MENU °C °F 1. Power: Press to turn the power on. Press and hold for three seconds to turn off the power. While powering off, the LCD will display the following symbols: POWER OFF °C 2. - Page 11 Temperature Recorder If the ‘REC” symbol blinks, it indicates the memory is full, and the LCD will display “REC FULL”. To set the recording interval, please refer to Page 9. 5. Relative mode: Press , the meter will memorize the present reading and will then display the difference between the new reading and the memorized value.
-
Page 12: Printing
Temperature Recorder 5.3 Printing Use the printer control buttons to initiate printing. OPEN TEMPERATURE RECORDER MENU MENU °C °F INST FEED PRINT 1. Instant printing: Press once to print out the date, time, and the INST PRINT present temperature ... - Page 13 Temperature Recorder 2. Start and stop printing: Press to start printing. Press the button again to stop printing. The LCD will display the symbol while printing. Please refer to Page 8 regarding print setup. 3. Feed: Press once to have the printer feed 2/3 FEED inch of paper out.
-
Page 14: Loading Thermal Paper
Temperature Recorder 5.4 Load Thermal Paper 1. Pull up the printer head lever. 2. Remove the paper cabinet cover. 3. Insert the paper into the slot. 4. Press a couple of times to load the paper into FEED the printer. MENU MENU °C... -
Page 15: Battery Replacement
Temperature Recorder 5.5 Battery Replacement 1. Turn off power before replacing the battery. 2. Replace all six (6) size AA, 1.5V batteries at the same time. For maximum battery life, alkaline batteries are recommended. -
Page 16: Attention
Temperature Recorder VI. ATTENTION 6.1 Master Reset If the meter appears to be in an unknown condition, it can be reset to its default setup. To reset the meter: 1. Turn off the power. 2. Press and hold simultaneously, then press , and the LCD will display “MASTER SETUP”. -
Page 17: Software
Temperature Recorder VII. Software 7.1 Installation System Required: Windows 95 / Windows 98 / Windows ME Windows NT 4.0. Minimum Hardware Required: PC with Pentium processor, 90MHz or higher 32 MB RAM 4X CD-ROM Drive or faster Recommended display resolution 800X600 At least 5 MB hard disk space available to install TestLink. -
Page 18: Introduction
Temperature Recorder 7.2 Introduction Main Screen Main menu Tool menu Real time Data window Graph option Reading display Real time graph Real time list Max/Min/Avg display Main Screen File: Open - Opens previously saved files from the hard drive. Save - Saves data from the the active window (when the Title bar is highlighted) to disk. - Page 19 Temperature Recorder DataLogger Data Sets List Data List Graph When the Temperature Recorder meter is connected to the PC, select "DataLogger" from main menu or click the tool bar to load recorded data from the meter. A progress indicator will display loading progress. If an error occurs, click "DataLogger"...
- Page 20 Temperature Recorder Tutorial Quick Start Recording real time data from PC. 1. Turn on the Temperature Recorder first, then connect it to a PC RS-232 serial port with the supplied cable. 2. Run the TestLink software. 3. If the connection is successful, the LCD simulation will display the same value as the Temperature Recorder.
- Page 21 Temperature Recorder Downloading recorded data from the memory of the Temperature Recorder and saving it to a file 1. Power on the Temperature Recorder. 2. Connect the Temperature Recorder to the 3. Start the SE500 program. 4. Choose Data Logger from the main menu or click from the tool bar.