Related Manuals for One World Touch LM-XX37-26 series
Summary of Contents for One World Touch LM-XX37-26 series
- Page 1 LM-XX37-26 Touch Monitor User Manual One World Touch, LLC Please retain this manual for future reference...
-
Page 2: Table Of Contents
Table of Contents Chapter 1 Introduction ........................3 Chapter 2 Product Views .........................4 2.1 Front View ........................4 2.2 Back View ........................4 Chapter 3 Getting Started .......................4 3.1 Connect the Touch Screen Monitor ................4 3.2 Touch Screen Driver Installation ................5 3.3 Adjusting the Monitor....................7 Chapter 4 Troubleshooting ......................10 Chapter 5 Warranty Policy ......................11 Chapter 6 Contact information ....................12... -
Page 3: Chapter 1 Introduction
Therefore, the warranty will only cover issues with the product alone. Because of technical or other external factors which leads to changes on product design and specifications, One World Touch, LLC will not give a separate notice. Warnings and Precautions This LCD monitor operates under high voltage. -
Page 4: Chapter 2 Product Views
Chapter 2 – Product Views 2.1 Front View 2.2 Back View Chapter 3 - Getting Started 3.1 Connect the Touch Screen Monitor • Ensure that the host device connected to the touch monitor is turned off. • Connect one end of the signal cable (VGA or DVI or HDMI) to the touch monitor and the other end is connected to the host device. -
Page 5: Touch Screen Driver Installation
3.2 Touch Screen Driver Installation In most cases a touch screen driver is not needed, however, if a driver is needed, it can be installed from the supplied CD-ROM. 3.2.1 Touch Screen User Modes： • Mouse Mode Supported by Windows XP, Windows 2000, Windows 7(32bit/64bit), Windows 8(32bit/64bit), Windows 8.1(32bit/64bit), Windows 10 (32bit/64bit), Ubuntu 10.04, Ubuntu 11.04, RHEL 6.0 •... - Page 6 3) Follow the screen prompts to complete the driver installation. • Calibrate the touch screen Select HID Touch menu in the Start menu, click on the submenu "Calibration".
-
Page 7: Adjusting The Monitor
• Touch the red cross on the screen • Click the “OK’ button to complete the calibration 3.3 Adjusting the Monitor Generally, you will not need to adjust the monitors display settings however, variations in video output and application may require adjustments to your touch monitor in order to optimize the display quality. - Page 8 only when the VGA input is selected) OSD Menu function description: Image Adjustment Brightness Adjusts the overall screen brightness. Contrast Adjusts the amount of difference between darkness and lightness. Gamma Adjusts the gamma value. Position adjustment (Only applicable for VGA input video) Phase Allows fine adjustments of the panel’s pixel dot clock phase.
- Page 9 Dynamic Contrast On / off. This feature increases the contrast and provides aclearer more detailed image. Aspect Ratio Switches the scaling method between full scaling and maintain aspect ratio Reset Resets all settings to factory defaults Information Displays monitor information...
-
Page 10: Chapter 4 Troubleshooting
Chapter 4 - Troubleshooting Failure Possible Reasons • Make sure the power button is in the on (ON) position, the power cord is properly connected to a grounded Power cannot be turned on power outlet and the power adapter is connected to the monitor. •... -
Page 11: Chapter 5 Warranty Policy
(3) years from the date of purchase. One World Touch, LLC shall not be liable to honor the terms of this warranty if the product has been used in any application other than that for which it was intended, or if it has been subjected to misuse, accidental damage, modification, or improper installation procedures. -
Page 12: Chapter 6 Contact Information
Chapter 6 – Contact Information One World Touch, LLC 3003 Howard Lane Austin, TX 78728 Customer service department: Tel：888-928-2929 Fax: 512-341-9301 E-mail: support@oneworldtouch.com www.oneworldtouch.com...
Need help?
Do you have a question about the LM-XX37-26 series and is the answer not in the manual?
Questions and answers