EPS EF90H-CLR User Manual

Darkstar ust efinity series edge free ultra-short throw fixed frame screen

Advertisement

Quick Links

DarkStar® UST eFinity Series
EDGE FREE® Ultra-short throw Fixed Frame Screen
Product Description:
The DarkStar® UST Series is an ultra-short throw fixed frame projection screen that uses EPV's EDGE
FREE® technology. It is designed for Ultra-Short Throw Projectors only, for use in environments where
ceiling light cannot be entirely controlled. It includes an LED backlight kit and an ultra-thin bezel to further
enhance the frame appearance.
Screen Maintenance
Dust, dirt and scratches on the projection screen surface will affect the quality and performance of the
projection image. For optimal results we advise to pay attention to the following instructions.
1) The screen surface has a horizontal lens structure. DO NOT wipe the screen up and down or in a circular
motion.
Wipe from left to right only.
2) Please clean the dust on the screen surface with a soft brush or microfiber cloth (rough towel or cloth may
damage the screen's surface).
3) Gently wipe the screen with a moistened microfiber cloth with mild soap diluted in water.
Notes:
The following precautions should be followed at all times to avoid damaging the material, which is
not covered under warranty.
Don't touch the screen material to avoid leaving fingerprints. Use gloves when handling the material.
Don't scratch the material, as it will leave permanent markings on the screen's surface.
Don't point to the screen material with a fingertip or other sharp objects to prevent damage to the
material.
Don't use acetone, benzene, alcohol and any other organic solvents to clean the screen material. Using
such chemicals will permanently damage the screen.
Rev. 04/27/17 DR
USER'S GUIDE
www.epvscreens.com
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EF90H-CLR and is the answer not in the manual?

Questions and answers

Summary of Contents for EPS EF90H-CLR

  • Page 1 DarkStar® UST eFinity Series EDGE FREE® Ultra-short throw Fixed Frame Screen USER’S GUIDE Product Description: The DarkStar® UST Series is an ultra-short throw fixed frame projection screen that uses EPV’s EDGE FREE® technology. It is designed for Ultra-Short Throw Projectors only, for use in environments where ceiling light cannot be entirely controlled.
  • Page 2 1. Frame and Edge Trim Parts List 2 pcs 2 pcs Main Frame Parts Edge Trim Parts item item vertical frame Part Part ½ horizontal frame Part Part ½ horizontal frame Part Part 2. Hardware Parts List Rev. 04/27/17 DR www.epvscreens.com...
  • Page 3: Frame Assembly

    Item Parts List Qty EF90H-CLR EF100H-CLR EF120H-CLR Center Joints (1) Elbow Joints (2) M4x6 Screws Spring Hook Spring Top wall brackets Φ5x50 Wall Screws Hollow Wall anchors Bottom wall brackets Angle cover LED light strip clip Center Support Bar white gloves...
  • Page 4 Step 4: Insert the springs (e) into the grooves of the frame. The spring’s hooks should be facing the front side of the frame. For the correct amount of springs to place into the frame, please refer to the table listed below. Note: The springs are pre-installed into the grooves of the frame.
  • Page 5: Screen Material Installation

    Screen Material Installation Please read this important note before proceeding with the installation process of the material. Before handling the DarkStar® UST material, put on the supplied pair of white gloves to avoid leaving fingerprint marks, dust or hand oil on the material’s surface. The DarkStar® UST material is very delicate and should be handled with extreme care.
  • Page 6 After all four corners have been attached, proceed to attach the vertical sides of the material. Begin in the center and move towards the corners from (3) to (4) to (5). Lastly, attach the horizontal sides of the material by starting with the center of the material and make your way towards the corners from (6) to (7) to (8).
  • Page 7: Center Support Bar

    Center Support Bar Step 11: Insert the Center Support Bar (i) into the upper top groove on the back of the frame with the bottom end near the approximate center point of the frame and rotate it in at an angle so that both ends of the bar are in alignment with the groove.
  • Page 8: Notice To Installer

    Edge Trim Start with the Step 12: Place the Edge Trim over each end of the frame and secure with M4x6 screws (c), center points first, then the rest of the corners as shown. Step 13: Install the angle cover (j) on each corner of the frame and install the LED light strip to hold down the angle cover.
  • Page 9 Please use the following installation instructions to obtain superior optical performance from the Retro-Reflective ALR (Ambient Light Rejecting) Screen. Example 1: Proper Projector Installation Example 2: Improper Projector Type/Installation Note: Improper installation will result in light loss and produce a dark image. This is due to the projector’s light reflecting in the wrong direction.
  • Page 10: Wall Installation

    Wall Installation Step 14: Measure the overall length and height of the frame and drill holes for the top brackets. Line up the wall brackets with the drilled holes on the installation location and screw them in using a Phillips screwdriver. If not installing into a structural wood stud, use a hollow wall anchor then screw in the M5x50 wood screws with a screwdriver.

This manual is also suitable for:

Ef100h-clrEf120h-clr

Table of Contents