Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for Zed-Bull Zed-Bull
- Page 1 Zed-BULL FOR PROFESSIONALS USER MANUAL...
-
Page 2: Table Of Contents
1. IMPORTANT NOTES 2. MAINTENANCE AND CLEANING 3. ACCESSORIES 4. SPECIFICATIONS 4.1 DIMENSIONS 4.2 TECHNICAL DETAILS 5. GENERAL INFORMATION 6. Zed-BULL MENU 6.1 TRANSPONDER IDENTIFICATION 6.2 TRANSPONDER CLONING 6.3 TYPING TRANSPONDER DATA MANUALLY 6.4 TESTING 6.5 SETTINGS 7. OVERVIEW OF PC SOFTWARE 7.1 MAIN MENU... -
Page 3: Important Notes
-Keep package in room conditions. -Clean the device with soft and dry piece of cloth. -If a problem occurs do not disassemble the device. Contact your local distributor or device manufacturer. ACCESSORRIES Complete package Zed-BULL security login card PC Usb cable... -
Page 4: Specifications
Power Adapter Lighter Adapter Transponder box SPECIFICATIONS DIMENSIONS Width 285 mm Height 285 mm Depth 105 mm Weight 0,6 kg External Power Supply 100/250 V – 50/60Hz AC Current 117 mA Power consumption 1,05 Watt ≅ Adapter Type 9-12 V DC TECHNICAL DETAILS Transponder Frequencies 125 -134 Khz... -
Page 5: General Information
12, 13, 4C, 33, 40, 41, 42, 44 VAG, 44 Mitsubishi, 45, 46, 61, 62, 65 and 73 for diagnostic devices. Zed-BULL has got token system, which is free of charge .when device is turned on, before logging in, number of tokens, 16 digit device serial number,... - Page 6 Tokens are loaded as in the steps below: 1.Choose 5 choice(settings) in the main menu. 2.Choose 4 choice(Load PC token) in the settings sub menu. 3.Device will give Outcode, outcode should be sent by e-mail to token@istanbulanahtar.com as a reply of this e-mail user will get In code, this In code should be entered carefully and correctly to the device, if In code is entered wrong repeatedly 5 times, device will want new In code.
- Page 7 -Enter In code button is clicked. If successfull token will be loaded to the device. If not successfull, Pc software will give an error message “Invalid Incode”, then user should check and enter the Incode again. All connections of Zed-BULL are shown in the picture below.
- Page 8 After Power switch of the Zed-BULL is turned on, user should put the Security login card on the antenna. Unless Security login card is put on the antenna at start up, the Zed-BULL functions won't work, Pressing button “R” allows to try logging in again. The Security login card is put on the antenna as in the picture below;...
-
Page 9: Zed-Bull Menu
Usage: Insert customer key to the Zed-BULL antena and Press “R” button on Zed-BULL keypad or use up and down arrow to highlight choice 1 on main menu and press enter(right arrow). An important point is; while reading the transponder, It should be put... -
Page 10: Transponder Cloning
Zed-Bull screen displays of some of identified transponders are as below. TRANSPONDER CLONING This menu is used for duplicating transponders. Usage: Insert customer key to the Zed-BULL antenna and highlight choice 2(Clone chip) on main menu and press enter(right arrow). - Page 11 The details of the chip will be displayed on the screen. Next, you will press the “W” button. S uitable transponders to write onto will be displayed on the Zed-BULL screen remove customer key from antenna and insert suitable transponder. Select the transponder type by pressing the listed numbers on the display.
- Page 12 Copying 4D transponders is possible only with Zed-BULL Client PC Software. User must connect to server to copy 4D transponders. Zed-BULL PC Software connects to the server and gets neccessary datas to write on to electronic key. User should choose correct communication port, car...
-
Page 13: Typing Transponder Data Manually
When this message is displayed, user must remove the original key from Zed- BULL antenna, other wise, Zed-BULL will try to write on to original key and it will cause data corruption with the original transponder. server will give approximate time for copy process, when user confirm the given time, copying process will start. -
Page 14: Testing
An important point is that the data entered manually, must include valid information for the 11,12,13 and 4C type transponders. Before writing process starts, Zed-BULL checks the validity of the data and informs the user if the data is non-valid. -
Page 15: Settings
SETTINGS This menu is used for choosing device language, updating device, getting device info and loading device token. Usage: Highlight choice 5 using up and down arrow and press enter, for language selection highlight choice 1 and press enter, language options will be displayed on the screen. - Page 16 VAG PIN READER VAG Pin Code reader automatically extracts the pin code of the car for VAG group. Adapter side is connected to the OBD of the car and the other side is connected to Zed-BULL. Zed-BULL VAG Pin Reader OBD II 1-Choose 6th choice(Pin Code Reader) from main menu.
-
Page 17: Overview Of Pc Software
Software Setup: Double click on the setup.exe icon and install the software. After installing software, with the USB cable given, connect Zed-BULL to PC using any of the USB ports. Click on Zed-BULL.exe to run the software. Note: to use the software .NET framework(minimum version 3.5) should be installed in your PC. -
Page 18: Extended Functions
fails, an error message will be displayed, if connection is succesfull all buttons will be active. In main menu window, normal read write operations are done, when “READ” button is clicked, the transponder identification is displayed on the software window. Writing to transponder is done in 2 steps;... -
Page 19: Eeprom & Mcu Applications
Important Notes: -User must use external IC programmer to read the Eeproms and Mcus. -The pictures of the IC programmer in Zed-Bull Pc software is for brand Omega-Mtrk IC Programmer. -Omega-Mtrk IC Programmer covers all the applications in the list and we suggest this programmer. - Page 20 -For BMW applications, user must be careful about the key number. When customer wants spare key, the original customer key should be read and the key number should be noted(Zed-BULL is able to show key number when read). In the PC software window proper key number should be selected.
- Page 21 3-Save the file with “.bin”or “.dat” extension with any name and to any location as you wish. 4-Open the file that you saved, using the Zed-Bull Pc Software, insert the suitable transponder to the antenna and click the “programme transponder”...
-
Page 22: Preparing Transponder Data
PREPARING TRANSPONDER DATA 7.2.2 Right top side of the main menu window is reserved for preparing data for 11,12 temic, 13 megamos, 4C texas and 33 renault transponders from eeprom bytes. This feature is added to the software for professionals. If the location of bytes that is related with transponder data is known this feature is used. -
Page 23: Hitag 2
BULL Pc software. Pages of hitag 2 transponders can be both read and written with Zed-BULL and Zed-BULL PC Software. Software shows transponder type, transponder mode, frequency mode, transponder pages and transponder configuration bits to the user and can be edited by the user. -
Page 24: Transponder Catalogue
TRANSPONDER CATALOGUE In transponder catalogue sub menu, user finds usefull informations about transponders and matching car models. Information about the IC type in immo box of the car is also given for most of the car models. KEY-FOB Programming key fobs manually is described step by step in this sub menu. -
Page 25: Database
Unlimited number of customer information can be stored in database section of the PC software. When a customer whose information exists in the database comes again, using recorded information, it is possible to make key. DISTRIBUTORS Here user will find contact details of Zed-BULL distributors around the world. -
Page 26: Settings
Eeprom & Mcu applications or transponder production applications and other applications uploading both ZBP and ZBC file is required. When user wants to update Zed-BULL for new version; only ZBP file needs to be uploaded to Zed-BULL. User should contact local distributor for ZBC and ZBP... - Page 27 Steps for updating Zed-BULL: 1-Choose Update Firmware choice in Settings sub menu. 2-The device will be in loader mode. The screen display should be as below. Or directly from Pc software user may click Update Mode button to get the device to loader mode.
-
Page 28: Support/Contact
SUPPORT/CONTACT 7.10 Whenever user has problems or questions this sub menu can be used. An e-mail will be sent to the manufacturer company directly. - Page 29 UALITY MANAGEMENT SYSTEM OF ISTANBUL ELEKTRONIK ANAHTAR VE GUVENLIK SIS. SAN. TIC. LTD. STI. IS REGISTIRED WITH THE STANDARD ISO 9001 : 2000 İSTANBUL ELEKTRONİK ANAHTAR GÜV. SİS. SAN. TİC. LTD. ŞTİ. ADRESS: HOCA UVEYZ MAH. VATAN CAD. NO:40 A FATİH/İSTANBUL/TÜRKİYE PHONE :0090 212 621 5793...
- Page 30 Appendix-A Precoded Transponder Automatic Detailed Detailed Eeprom & MCU Applications Transponder for ready to start module immo box immo board Code Diagnostic the car recognition picture picture √ √ √ √ √ Opel immo2 Siemens immobox √ √ √ √ √...
- Page 31 √ √ √ Toyota Corolla Bosch √ √ √ Toyota Yaris 2 √ √ √ Toyota Corona √ √ √ √ Renault Laguna 2 √ √ √ √ Mercedes Actros, Atego Temic immobox √ √ √ √ Renault Megane 2 √...
- Page 32 √ √ √ √ √ Audi Delphi immobox √ √ √ √ Peugeot, Fiat, Lancia, Citroen Texton immobox √ √ √ √ Chrysler SKIM immobox √ √ √ √ Mazda 323 Temic √ √ √ Suzuki Grant vitara √ √ √...