Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for MAX SMART SG2
- Page 1 INSTALLATION AND USER MANUAL GSM+WiFi Alarm Security System™...
-
Page 2: Control Panel Features
White(Fast blinking):searching GSM network White(slow blinking): GSM signal is normal Status / GSM Signal Indicator Built-in Product name: Power / Network status Indicator 7.4V 500mAh lithium SG2 GSM+WiFi Panic (SOS) Support wireless accessories: Panel Power supply: 10 remote control, 100 wireless detectors... - Page 3 7 of this manual. 2. Enter your user code, followed by ”#”. After each key you press on your phone, you hear one beep of confirmation. Wait until you have heard this beep of confirmation before pressing the next key. Change the language 3. Select the operations to control the panel (see instructions in the table below). By default the language of the SG2 control panel is set to English. If you wish to change the system language, refer to the instructions “Change system language” on page 12 of this manual. “System Note language” refers to the language of the SMS you receive from the control panel. The call will end automatically if you do not send any command within 30 seconds. Arm / Disarm the system Voice Instructions The alarm system can be armed or disarmed by SMS, by App and by phone call.
- Page 4 Zone setup of accessories Store Phone numbers for SMS SMS Operations notifications Every detector can be assigned to 4 different categories of zones: Home Mode Zone, Delay Zone, Send: IMPoRtANt: BEFoRE USING FoR tHE Normal Zone and 24-H Zone. To assign a detector to a zone, open its case and move its jumpers FIRSt tIME according to the drawing below: SAVE A PHONE NUMBER FOR SMS NOTIFICATIONS. (Refer to instructions on the opposite column) Only stored numbers can control and configure the system. SMS numbers: INSERT A SIM CARD IN THE CONTROL PANEL BEFORE STARTING SMS OPERATIONS.
-
Page 5: Store Phone Numbers
Disarm the System Settings Enquiry Store Phone Numbers Change Zone Name Send: Send: Send: Send “91~99”. For example for zone 1, send: Zones names: System disarmed. Phone numbers: System:Disarmed AC power:on Entry delay time:0sec Exit delay time:0sec Copy, Paste, then Edit Siren time:5min Arm the System (case sensitive): Disarm password:1234 Send: Zones names: Copy, Paste, then Edit 1.Entrance door alarm (case sensitive): Note The value of default settings will be changed after having set up the system. -
Page 6: Disarm Password
SMS Alert for Accessory Low Battery Entry and Exit Delay time Siren Volume and Ringing time Disarm Password (available for two-way acessories such as Motion Detectors) Send: Send: Send: For accessories assigned to zones that have been renamed, an SMS will be sent under the format “Zone name + low battery”. Bedroom PIR low battery Disarm password (4 digits): Entry delay time(0-300sec):0 Siren volume(0=Mute,1=High):1 1234 Exit delay time(0-300sec):0 Siren ringing time(1-9min):5 For accessories assigned to zones that have not been renamed, an SMS will be sent under Copy, Paste, then Edit the format “Zone number + low battery”. -
Page 7: Call Repetition
Call repetition Change system language Accessories If the user does not pick up his phone when Send the code of the language. For example, the alarm detects an intrusion, the alarm will for English, send “0001”. Wireless Remote Control keep re-dialing the number a certain amount of times. 0001 Disarm Send: LED indicator Home Mode Arm the system Call repetition:5 Refer to the table below for the full list of Press the Arm button "... -
Page 8: Wireless Motion Detector
Wireless Motion Detector Emergency Mode Features The MS-01A (or MS-02A: Pet-Immune Motion Detector) is a high performance wireless Regardless the status of the system, the alarm motion detector boasting a digital dual-core fuzzy logic infrared control chip with intelligent is triggered when the SOS button "SOS" is analysis. This technology identifies interferences created by body motion and reduces the pressed on the remote control. - Page 9 Usage Testing Open the case and remove the battery activation strip. Self-testing will start for 30 seconds. A. After the installation, turn the detector on. After one minute of self-testing, press the test button, walk in the scope of detection and watch the LED indicator to make sure the detector is working. When the sensor is in operation, if it is B. The LED indicator blinks once when body movement is detected. triggered more than twice within 3 minutes, it will switch to standby mode to save power. C. Adjust the detector angle to achieve the best detection performance.
-
Page 10: Wireless Door / Window Contact
Wireless Door / Window Contact Installation Features Open the case and remove the battery activation strip. Mount the sensor on the door and the magnet on the The ES-D3A is a Door / Window Contact that can be installed on doors, windows, and any other door frame. objects that open and close. The sensor sends signals to the control panel when the magnet is Make sure the magnet is placed above the transmitter. separated from the transmitter. - Page 11 Register an Additional Siren Troubleshooting and Safety Instructions The control panel of the SG2 features a built-in 100 dB siren. Your Maxsmart security system supports additional indoor and/or outdoor sirens so to enable you to extend your system according to your needs. To register an additional Maxsmart siren, refer to the instructions provided in the manual that Issue Cause of malfunction Solution comes with your siren. The control panel is switched Turn the power on No response following interaction with the AC Power failure Contact your electricity provider control panel Backup batteries are empty Plug the AC adapter to an AC socket The control panel is not in Make sure the control panel is in Connection mode Connection mode...
- Page 12 Precautions Standards For a safer use of the product and to optimize the lifespan of the product, we recommend you to follow the precautions below: This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European Directive 2002/96/EC in order The wireless accessories must be connected to the control panel. to be recycled or dismantled to minimize its impact on the environment. Low power voltage may affect transmission distance. Do not press the SOS key on the remote control if it is unnecessary to avoid disturbing For further information, please contact your local or regional authorities. neighborhood. Check the system regularly to make sure the system works properly. Electronic products not included in the selective sorting process are potentially dangerous for the The control panel is neither waterproof nor moisture-proof, install it in a shady, cool and dry environment and human health due to the presence of hazardous substances.
- Page 13 FCC Information and Copyright This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 14 Rm 402-403, 4th Floor Skyworth Semiconductor Design Building West Wing, Nanshan District, Shenzhen, China. www.maxsmart.cn...
Need help?
Do you have a question about the SG2 and is the answer not in the manual?
Questions and answers