JULY.2004 CAUTIONARY NOTES Accessory Owner’s Manual ENGLISH”(#SD000453) JAPANESE”(#SD000452) PART LIST Due to one or more of the following reasons, parts with parts code ******** Option cannot be supplied as service parts. • Part supplied only as a component in a complete assembly Foot Switch FS-5U (BOSS) •...
CUBE-60D LOCATION OF CONTROLS PARTS LIST PART CODE CATEGORY PART NAME DESCRIPTION Q’TY 13449146 JACK,EXT TERMINAL 6.5MM JACK YKB21-5012 (W/SW) SD000042 SCREWS JACK NUT SD000099 SWITCH PUSH SWITCH ESB64619 SD000082 KNOB,BUTTON PUSH BUTTON SD000044 DIODE LED GREEN SD000045 DIODE LED RED...
JULY.2004 CUBE-60D EXPLODED VIEW(CABINET) fig.explo-cab [PARTS] PART CODE CATEGORY PART NAME DESCRIPTION Q’TY SD000467 CASING CABINET ASSY NOTE:”CABINET ASSY includes the following parts (2,4,5,7-9,12,14) HARDW00067 CASING POAT TUBE SD000066 CASING TRIM SD000459 CASING CORNER PROTECTOR SD000461 CASING HANDLE RUBBER SD000462...
JULY.2004 PARTS LIST fig.part1e Due to one or more of the following reasons, SAFETY PRECAUTIONS: parts with parts code ******** cannot be supplied as service parts. The parts marked have safety-related characteristics. Use • Part supplied only as a component in a complete assembly only listed parts for replacement.
Page 9
CUBE-60D PWB ASSY SD000408 PANEL PCB ASSY F5209151 LM3886TF IC(POWER AMP IC) IC6 on M SD000493 NJM78M12DLA IC (V RGL) IC15 on M SD000494 NJM79M12DLA IC (V RGL) IC16 on M 03015923 S-80130ANMC IC (RESET) IC3 on M 01678512 UPC2933T-T2...
Page 10
JULY.2004 FUSE,FUSE HOLDER F2559307 RADIAL TYPE MRT 100MA/250V FUSE6 on M F2559305 RADIAL TYPE MRT 2 A FUSE2,FUSE3 on M SD000503 FUSE(RADIAL TYPE) MRT315MAL/250V FUSE4,FUSE5 on M SD000251 FUSE HOLDER FC-201 for FUSE1 on M F2559504 FUSE 5ST 2A/250V FUSE1 on M CONNECTOR 13369570 B2B-PH-K-S (2P)
Page 11
CUBE-60D MISCELLANEOUS SD000489 LED HOLDER LH-5-7 for LED F3459105 TERMINAL JH-8M3 TER3 01786045 SW HOLDER AT-217K SD000475 HIMERON 95 X 80 X 0.5T for TRANSFORMER SD000478 PU SPONGE W / ADH 90 X 25 X 4T for CHASSIS TOP SD000483...
JULY.2004 CHECKING THE VERSION TEST MODE NUMBER Required Equipment Set up the CUBE-60 as described below. • 1 pair of headphones [Connections] • 3 BOSS FS-5U foot switches (sold separately) Connect an FS-5U foot switch to each of the three FOOT SW jacks (CH •...
Page 13
CUBE-60D 3. Switch Test POWER LED If there is a failure in any of these tests, the procedure does not advance to the next test. BRIGHT Switch Test Press the BRIGHT switch. If the test results in OK (pass), the POWER LED lights.
Page 14
JULY.2004 WHEN EXCHANGING AC CORD Please note the following cautions when exchanging the AC cord. Cautions Before soldering wiring and terminal, wind the wire 1.5 times around the terminal (refer to Fig. 1). fig.2 Fig. 1 When removing the AC cord from the board, be sure not to leave any wiring debris on the terminals.
Need help?
Do you have a question about the CUBE-60D and is the answer not in the manual?
Questions and answers