Advertisement
Quick Links
USER'S MANUAL
Acknowledging Special Precautions and the FCC Notice Cautions.
Modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
FCC compliance Information
This device complies with part 15 of FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received.
Including interference that may cause undesired operation.
Information to User
This equipment has been tested and found to comply with the limits for a Class B digital
device, Pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio Frequency energy and, if not
installed and used in accordance with th einstruction, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, whic h can
be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
> Reorient or relocate the receiving antenna.
> Increase the separation between the equipment and receiver
> Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Read this information before using your product.
- 1 -
Advertisement
Related Manuals for UNIMO Technology PJ-100NW
Summary of Contents for UNIMO Technology PJ-100NW
- Page 1 USER'S MANUAL Read this information before using your product. Acknowledging Special Precautions and the FCC Notice Cautions. Modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC compliance Information This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: 1.
- Page 2 RADIO FREQUENCY ENERGY SAFETY INFORMATION This UNIMO transceiver has been tested and complies with the standards listed below, in regards to radio Frequency(RF) energy electromagnetic energy(EME) generated by the transceiver > FCC RF exposure limits for Occupational use only. RF exposure limits adopted by the FCC are generally based on recommendations from the national council on radiation protection and measurement, &...
-
Page 3: Product Introduction
> Turn OFF your transceiver while on board an aircraft when so instructed, Use of the transceiver must be in accordance with airline regulations and/or crew instructions. 1. PRODUCT INTRODUCTION THE PJ-100NW LMR(Land Mobile Radio) of UNIMO Technology Co. Ltd. is a sophisticated State-of-The-Art unit which incorporates The modern technology available in Tow-Way Radio Communications. -
Page 4: Lcd Display
Fig.1 PJ- 100NW TRANSCEIVER 1.1 FRONT, SIDE, TOP OVERVIEW 1.2 LCD DISPLAY - 4 -... -
Page 5: How To Use
2. HOW TO USE 2.1 POWER ON/OFF, VOLUME CONTROL Turing the power switch clockwise turn power ON and sets the volume level. When the power is on, transceiver's ID and name appear on the LCD 2.2 PUSH-TO-TALK(PTT) SWITCH When depressed and held, engages the transmitter and puts radio in the transmit mode. at that time, TX lamp(red) is lighted. - Page 6 The TX output is selected between HIGH(5W) and LOW(1W). If press the UP button with PTT button pressed, it is converted to "H"(High). If press the DOWN button with PTT button pressed, it is converted "L"(Low). 2.6 TRANSMISSION In Tx mode, as soon as pressing the PTT button, DTMF and 5-Tone ID are transmitted. At that time, you can't communicate and the Rx/Tx lamp is lighted.
- Page 7 1) Transmit Mode(PTT Switch Depressed) -. Continuous RED Light : Normal Transmission -. Flashing RED Light : Low Battery -. Flashing Pink : Selective Call 2) Receive Mode(PTT Switch Not Depressed) -. Continuous Green(5 Seconds) : Channel monitor active -. Flashing Pink : Selective Call or Call alert present -.
- Page 8 -. After selecting the new channel. -. After ending the calls(After receiving or transmitting) 2.16 Cloning Operation Cloning is the function that clones data, such as frequency/time/scan, to other PJ-100NW, transceivers. 1.Prepare the cable (PECLONA) for PJ-100NW. (* Available in agency) 2.Turn on the source transceiver with PTT button pressed and turn on the target transceiver with...
-
Page 9: General Specification
3. GENERAL SPECIFICATION GENERAL Operating Mode Conventional (nontrunked) only Frequency Range UHF : 136 ~174 MHz Frequency Stability ±2.5PPM(-30 to +60 ) ℃ Frequency Control PLL Synthesizer Programmable Channels 128 Channels/16 Group Channel Spacing Dual Channel Spacing 12.5/25kHz Speaker Impedance 16 ohm Dimensions 126mm(H)×53mm(W)×38mm(D) - Page 10 Audio Distortion Less than 5% at rated output Audio Response +1, -3 dB from 6dB per octave de-emphasis characteristic from 300~3000Hz Speaker Impedance 16 ohms IF Frequencies 21.4MHz and 455kHz Input Impedance 50 ohms TRANSMITTER RF Power Output 5/1Watt Spurious and Harmonic 60dB FM Hum and Noise 40dB(12.5KHz), 45dB(25KHz)