Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Unique Gas Products Manuals
  4. Hob
  5. UGP-30E CT2
  6. Installation instructions manual

Unique Gas Products UGP-30E CT2 Installation Instructions Manual

Hide thumbs Also See for UGP-30E CT2:
1
2
3
4
5
6
7
8
9

Advertisement

Quick Links

Download this manual See also: Owner's Manual
U G P - 3 0 E
–
C T 2

Installation Instructions

Be sure the rangetop is properly installed and grounded by a qualified technician. It is the
responsibility of the technician to make certain that your rangetop is properly installed.
Situations cause by improper installation are not covered under the warranty. Any
expenses incurred due to such situations will not be paid by the manufacturer of the
rangetop.
Leak testing of the appliance shall be conducted according to the manufacturer's
instructions, or according to local building codes and gas regulations in your area.
GAS CONNECTIONS (All Units)
NOTICE TO MASSACHUSETTS APPLIANCE DEALERS:
Be sure this document is included in all gas rangetop appliances sold to consumers in
the State of Massachusetts.
NOTICE: Massachusetts law requires the following:
Appliances must be installed by a licensed plumber or gas fitter.
Appliances must be connected with a three (3) foot (36" maximum length)
flexible gas connector and
A "T" handle type manual gas valve in the gas supply line to the appliance
Have the dealer where you purchase your new rangetop install it or have them
recommend a qualified installer. Installation must conform with local codes. In the
absence of local codes, the installation must conform with the National Fuel Gas
Code, ANSI Z223.1-Latest Edition in the U.S.A. or the CAN/CGA B149.1 or .2
Installation Codes in Canada.
The rangetop should be connected to the supply line with 1/2-inch black iron pipe
or a certified flexible type stove connector. To prevent gas leaks, put an approved
sealing compound which is resistant to liquefied petroleum gases on all threaded
connections.
Important: Do not apply pressure directly to the rangetop manifold pipe when
tightening supply connections. The manifold pipe should be held securely at the
pressure regulator to prevent twisting. Hold the pressure regulator with a wrench
during the tightening of the connection, or the manifold pipe may be twisted and
split and cause a dangerous leak.
The installation of rangetops designed for manufactured (mobile) home installation
must conform with the Manufactured Construction and Safety, Title 24 CFR, Part
3280, [formerly the Federal standard for Mobile Home Construction and Safety,
Title 24, HUD (Part 280)] in the U.S.A. or C.S.A. Standard CAN/CGA Z240.4.2 in
Canada or, when such standards are not applicable, with local codes.
6
.

Advertisement

loading

Related Manuals for Unique Gas Products UGP-30E CT2

Summary of Contents for Unique Gas Products UGP-30E CT2

  • Page 1: Installation Instructions

    U G P - 3 0 E – C T 2 Installation Instructions Be sure the rangetop is properly installed and grounded by a qualified technician. It is the responsibility of the technician to make certain that your rangetop is properly installed. Situations cause by improper installation are not covered under the warranty.
  • Page 2 U G P - 3 0 E – C T 2 The installation of rangetops designed for recreational vehicle installation must conform with state or other codes or, in the absence of such codes, with the standard for recreational vehicles. ANSI A119.2.2–1982 in the U.S.A. or CAN/CGA Z240.4.2 in Canada.
  • Page 3 U G P - 3 0 E – C T 2 It is the responsibility of the installer to make certain that the rangetop is properly adjusted at the time of installation. Situations caused by improper adjustments or improper installation are not covered under the warranty. Any expenses incurred due to such situations will not be paid by the manufacturer of the appliance.

  • Page 4: Wall Installation

    U G P - 3 0 E – C T 2 rangetop to such combustible surfaces above the 36” (91.4 cm) counter height. Within the 6” (15.2 cm) side clearance to combustible vertical surfaces above 36” (91.4 cm), the maximum wall cabinet depth must be 13” (33.0 cm) and wall cabinets within this 6”...

  • Page 5: Island Installation

    U G P - 3 0 E – C T 2 should be installed a minimum of 30” to a maximum of 36” above the cooktop surface. Recommended CFM should be g 450 cfm for the 30” rangetop. Do not install with a downdraft ventilation system Island Installation Note: There must be a minimum of 6”...
  • Page 6 U G P - 3 0 E – C T 2 high. There must be a minimum of 6” (15.2 cm) side clearance from the rangetop to such combustible surfaces above the 36” (91.4 cm) counter height. Within the 6” (15.2 cm) side clearance to combustible vertical surfaces above 36”...
  • Page 7 U G P - 3 0 E – C T 2 Make the countertop cut-out following the dimensions given in the illustration above. Base below rangetop must be of a non-combustible material.
  • Page 8 U G P - 3 0 E – C T 2 Installing the Rangetop Remove the rangetop from its package and set aside all burners, burner caps and grates. Gently slide in the cooktop into the cut-out, make sure your cut-outs are there for the gas connection and electrical hookup (if you choose to use it).
  • Page 9 U G P - 3 0 E – C T 2 piped connection. Never reuse an old connector when installing a new rangetop. If the hard piping method is used, you must carefully align the pipe. To prevent gas leaks, use pipe joint compound resistant to NG gases on all male external pipe threads.