Adjustments - Poulan Pro 961220014 Operator's Manual

DRIVE CONTROL
"STANDARD DRIVE" CONTROL
• Self-propelling is controlled by holding
the operator presence control bar down
to the handle and pushing the drive
control lever forward until it clicks; then
releasing the lever.
• Forward motion will stop when the op-
erator presence control bar is released.
To stop forward motion without stopping
engine, release the operator presence
control bar slightly until the drive control
disengages. Hold operator presence
control bar down against handle to con-
tinue mowing without self-propelling.
• To keep drive control engaged when
turning corners, push down on handle
and lift front wheels off ground while
turning lawn mower.
Operator presence control bar
control
TO DRIVE
ENGAGE CONTROL
DRIVE CONTROL DISENGAGED
"DUAL BAIL" DRIVE CONTROL
• To start forward motion, lift drive control
bar up to handle.
• To stop forward motion, release drive
control bar.
Operator pres ence con trol bar
DRIVE DRIVE
CONTROL CONTROL
ENGANGED DIS EN GAGED
"AUTOWALK" DRIVE CONTROL
• Self-propelling is controlled by hold ing
the operator presence control bar down
to the handle and pulling the drive con-
trol lever rearward to the handle. The
farther toward the handle the lever is
pulled, the faster the unit will travel.
• Forward motion will stop when either
the operator presence control bar or
drive control lever are released. To stop
forward motion without stop ping engine,
re lease the drive control lever only. Hold
op er a tor presence control bar down
against handle to con tin ue mowing with-
out self-propelling.
NOTE: If after releasing the drive control the
mower will not roll backwards, push the mower
forward slightly to disengage drive wheels.
FRONT WHEEL DRIVE MODELS ONLY:
• To keep drive control engaged when
Drive
turning corners, push down on the
handle to lift the front wheels off the
ground while turning lawn mower.
"AUTOWALK" ADJUSTMENT
Over time, the drive control system may
become "loose", resulting in decreased
speed. There is a turnbuckle on the
un der side of the drive control housing to
increase tension on the drive cable. Pro-
ceed as follows:
• Turn unit off and disconnect spark plug
wire from spark plug.
• Turn nut on underside of drive control to
increase drive speed.
• Operate mower to test drive speed.
Readjust as required.
• If condition fails to improve after the
above steps (forward speed remains
the same), your drive belt is worn and
should be re placed.
Operator presence control bar
Drive
control
TO
lever
ENGAGE
Adjustment DRIVE
turnbuckle CONTROL DISENGAGED
12
"VARI-SPEED" DRIVE CONTROL
• Self-propelling is controlled by hold-
ing the operator presence control bar
down to the handle and pulling the drive
control bar up to the handle. The closer
to the handle the bar is pulled, the faster
the unit will travel.
• Forward motion will stop when either the
operator presence control bar or drive
control bar are released. To stop forward
motion without stop ping engine, re lease
the drive control bar only. Hold op er a tor
presence control bar down against
handle to con tin ue mowing without self-
propelling.
NOTE: If after releasing the drive control the
mower will not roll backwards, push the mower
forward slightly to disengage drive wheels.
FRONT WHEEL DRIVE MODELS ONLY:
• To keep drive control engaged when
turning corners, push down on the
handle to lift the front wheels off the
ground while turning lawn mower.
DRIVE
CONTROL
ENGAGED
DRIVE
CONTROL
VARI-SPEED "THUMBSCREW"
ADJUSTMENT
Over time, the drive control system may
become "loose", resulting in decreased
speed. There is a thumbscrew on the
un der side of the drive control housing to
increase tension on the drive cable. Pro-
ceed as follows:
• Turn unit off and disconnect spark plug
wire from spark plug.
• Rotate thumbscrew counter-clockwise to
tighten the drive cable.
• Operate mower to test drive speed.
• If condition fails to improve after the
above steps (forward speed remains
the same), your drive belt is worn and
should be re placed.
NOTE: If mower begins to "creep" forward,
the drive cable is too tight. Rotate thumb-
screw clockwise to loosen drive cable.
Thumb-
screw
Operator presence control bar
VARI-SPEED "BLOCK" ADJUSTMENT
Drive
Over time, the drive control system may
control bar
become "loose", resulting in decreased
speed. There are holes in the drive control
DRIVE
CONTROL housing to increase tension on the drive
DISENGAGED
cable. Pro ceed as follows:
1. Turn unit off and disconnect spark plug
wire from spark plug.
2. Loosen nut, move drive control hous-
ing down handle to the next hole and
retighten nut.
3. Operate mower to test drive speed.
4. If condition fails to improve after the
above steps (forward speed remains
the same), your drive belt is worn and
should be re placed.
TO ADJUST, MOVE DOWN TO NEXT HOLE
13