Advertisement
Quick Links
Advertisement
Summary of Contents for Condeco Desk V2 Screen
- Page 1 Condeco Desk V2 Screen Operational Description Version 1.0 prepared by Xiaofei Zhang...
- Page 2 Contents This is a Heading 1 ............................5 This is a Heading 2 ........................... This is a Heading 1 Numbered ......................1.1. This is a Heading 2 Numbered....................Here’s a table: ..............................About Us ..............................16 Powering Change ..........................16 Who We Work With ..........................
- Page 3 Desk V2 Screen Design Spec 1. Display: 2.8” LCD 320 x 240 (QVGA) , 4 Wire SPI [KD028FM-1-TP] 2. Touch sensor: 4 wire Resistive touch 3. LED Light bar to display status 4. Processor: CC3200 from Texas Instruments with integrated ARM Cortex M4 processor 5.
- Page 4 UniFlash v3.4.0 on you PC. 5. Condeco Desk V2 Screen firmware. Desk V2 Screen Firmware Installation: 1. Connect the Desk V2 Programming cable to your PC. 2. Connect the Desk V2 screen’s power lead to your PC’s USB port.
- Page 5 4. Click File on the UniFlash Manu bar and select Open Configuration. 5. Select and open condeco_prod.usf in C:\ti\uniflash_3.4\condeco\ 6. The COM Port number should be the port the USB Programming Cable connected. It can be find in computer’s Device Manager.
- Page 6 7. Make sure following boxes have been Checked.
- Page 7 8. Click Format button to format the desk screen’s memory. Choose the size of the memory as 1Mb.
- Page 8 Condeco firmware onto the V2 Desk Screen. 11. Once Operation Program returned appears, the programming has completed. 12. Power off the Desk V2 screen by unplug the power lead from the USB port. 13. Disconnect the programming cable. 14. Put the back plate on.
- Page 9 3. To Config http/ https: In the config.ini file, “usehttps=0” for http. Set to port 80. “usehttps=1” for https. Set to port 443. Save the change.
- Page 10 Key in the URL at: “deskservicehost=” and at “screenservicehost=” Save the change. 5. To set the secreen rotate position: 1) Set the rotation at 0 °, for install the Desk V2 screen on the desk. In the config.ini file, set “rotation=0” Save the change.
- Page 11 2) Set the rotation at 180°, for install the Desk V2 screen on the division. In the config.ini file, set “rotation=180”. Save the change. 6. Setup the WiFi connection: In the config.ini file, Key in the WiFi SSID at “ssid= “...
- Page 12 7. Finish. Desk V2 Screen User Instruction 1. Plug the Desk V2 screen’s USB connecter into a PC’s USB port or a USB charger to get the 5V power supplied to Desk V2 screen. 2. Desk V2 screen’s LED bar will lights up.
- Page 13 7. After completed the update checking, screen will finish the booting process and starts the desk booking mode. 8. Swipe the RFID card on the Desk V2 screen to book the desk. 9. Once the desk has been booked, the screen and LED bar will be in...
- Page 14 10. To cancel or finish the booking, just swipe the RFID card on the screen again. Then screen will be in green again to indication the desk is free.
- Page 15 USB cable(USB 2.0) The distance between user and products should be no less than 20cm la distance entre l'utilisateur et les produits devraient être au moins 20 cm...
- Page 16 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Need help?
Do you have a question about the Desk V2 Screen and is the answer not in the manual?
Questions and answers