Advertisement
USER'S MANUAL
Users of these drivers must read and un-
derstand the safety features and operating
instructions outlined in this manual.
65 Spring Lane Farmington, CT 06032-3311
Tel. 860.677.7331
German Seite
French Page
Español Página 31
IMPORTANT
The Fletcher-Terry Company
•
800.843.3826 • Fax 860.676.8858
11
21
•
www.fletcher-terry.com
1
FORM 080102
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Fletcher-Terry Pneumatic FrameMaster
- Page 1 Español Página 31 IMPORTANT Users of these drivers must read and un- derstand the safety features and operating instructions outlined in this manual. The Fletcher-Terry Company 65 Spring Lane Farmington, CT 06032-3311 • • Tel. 860.677.7331 800.843.3826 • Fax 860.676.8858 www.fletcher-terry.com...
-
Page 2: Safety Instructions
The purpose of the Pneumatic FrameMaster® and Pneumatic FlexiMaster® is to insert Fletcher Framer’s Points and Flexible Framer’s Points in wooden frames to secure the glazing, matboard, artwork and backing material. - Page 3 Make sure all screws and caps are securely tightened. 12. Do not use the driver if the safety warning label is missing or unreadable. Contact a Fletcher-Terry Customer Care Represen- tative for a replacement. 13. Only use points, parts, and accessories recommended by Fletcher-Terry.
-
Page 4: Operating Instructions
OPERATING INSTRUCTIONS The Pneumatic FrameMaster® and Pneumatic FlexiMaster® are de- signed to insert points into wooden frames to secure artwork, mat, glass, and backing material. Fletcher Flexible Framer’s Points are used when it is likely the secured material may be removed and reinstalled or re- placed. - Page 5 neumatic FrameMaster®: 1. Connect the point driver to the air supply before loading points. 2. Lay the driver on a table, release the magazine latch and slide the magazine cover fully open. Hold a full stack of Framer’s Points at an angle with the glue side down, and the sharp end of the points under the lip of the magazine groove as shown at A...
- Page 6 Operation of Pneumatic Point Drivers 1. Wear safety glasses and ear protection recommended in Safety Instructions, Figure 1. 2. Place the picture frame face down on a flat surface. 3. Rest the stabilizing shoe flat on the backing and push the nose piece firmly against the frame as shown in Figure 5.
-
Page 7: Maintenance (Daily)
Stabilizing Shoe to the driver with Figure 7 the two screws removed in step 2. 6. This procedure applies to both the Pneumatic FrameMaster® and Pneumatic FlexiMaster®. 7. Connect the driver to air supply, reload a stack of points and close the magazine cover. -
Page 8: Troubleshooting
Trouble Shooting CAUTION: ALWAYS disconnect air supply before performing any service procedure. Symptom Probable Cause Correction Air leak Loose screws Tighten screws Connector nipple loose Tighten connector Driver does not Inadequate air supply Verify and correct fire, or is sluggish supply and pressure Inadequate lubrication Put 1 or 2 drops of oil in... - Page 9 Pneumatic FrameMaster ® Ref.No. Part No. Description Quantity 12-635 Stabilizing Shoe 12-636 Upper Guide 12-637 Lower Guide 12-638 Trigger 12-639 Trigger Spring 12-640 Trigger Pin 12-641 Retaining Clip 12-642 End Cap 12-643 End Cap Screw 12-644 Stabilizing Shoe Screw 12-645 Lower Guide Mtg.
- Page 10 Pneumatic FlexiMaster ® Ref.No. Part No. Description Quantity 12-635 Stabilizing Shoe 12-670 Upper Guide 12-671 Lower Guide 12-672 Trigger 12-639 Trigger Spring 12-640 Trigger Pin 12-641 Retaining Clip 12-673 End Cap 12-643 End Cap Screw 12-644 Stabilizing Shoe Screw 12-645 Lower Guide Mtg.
Need help?
Do you have a question about the Pneumatic FrameMaster and is the answer not in the manual?
Questions and answers