Subscribe to Our Youtube Channel
Related Manuals for Hafco M-16
Summary of Contents for Hafco M-16
-
Page 1: Instruction Manual
Page 1 Instructions Manual for M-16 (W347) 07/06/2017 INSTRUCTION MANUAL M-16 Chisel Morticer (240V) 125mm timber width capacity W347... - Page 2 Page 2 Instructions Manual for M-16 (W347) 07/06/2017 CHISEL MORTISER MODEL M-16...
-
Page 3: General Safety Rules
Page 3 Instructions Manual for M-16 (W347) 07/06/2017 GENERAL SAFETY RULES Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury. - Page 4 Page 4 Instructions Manual for M-16 (W347) 07/06/2017 16. USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by manufacturer may cause hazards or risk of injury to persons. 17. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in “OFF” position before plugging in power cord.
- Page 5 Page 5 Instructions Manual for M-16 (W347) 07/06/2017 ADDITIONAL SAFETY RULES FOR CHISEL MORTISERS 1. DO NOT OPERATE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBTAIN ADVICE FROM YOUR SUPERVISOR, instructor, or another qualified person if you are not familiar with the operation of this machine.
-
Page 6: Power Connections
Page 6 Instructions Manual for M-16 (W347) 07/06/2017 WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY. SAVE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. CONNECTING TOOL TO POWER SOURCE POWER CONNECTIONS A separate electrical circuit should be used for your tools. -
Page 7: Unpacking And Cleaning
Page 7 Instructions Manual for M-16 (W347) 07/06/2017 Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord, which has a grounding type plug and a receptacle, which will accept the tool’s plug. When using an extension cord, be sure to use one heavy enough to carry the current of the tool. -
Page 8: Operating Controls And Adjustments
Page 8 Instructions Manual for M-16 (W347) 07/06/2017 ASSEMBLY WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL. RAISING AND LOWERING HANDLE 1. -
Page 9: Depth Stop
Page 9 Instructions Manual for M-16 (W347) 07/06/2017 Fig 4 FENCE The fence (A) Fig. 5, can be moved in or out by loosening lever (B), sliding fence to the desired position and tightening lever (B). Fig5 Fig6 DEPTH STOP A depth stop guide (A) Fig. - Page 10 Page 10 Instructions Manual for M-16 (W347) 07/06/2017 INSTALLING CHISEL & BIT 1. Loosen lock screw, shown in Figure 7. Fig 7 Fig 8 2. Insert chisel bushing (with the hole facing forward) into the head. Tighten the screw just enough to hold the chisel in place.
-
Page 11: Wiring Diagram
Page 11 Instructions Manual for M-16 (W347) 07/06/2017 Fig 9 Fig 10 3. Use a small, triangular, smooth file to relieve the inner corners of the chisel. See Fig.10. Remove any burrs from the outside of the chisel with a fine oilstone. - Page 12 Page 12 Instructions Manual for M-16 (W347) 07/06/2017 Parts Diagram for M-16 M-16 Chisel Mortiser １０ V.02 01-11-2010...
- Page 13 Page 13 Instructions Manual for M-16 (W347) 07/06/2017 PART LIST For M-16 M-16 Chisel Mortiser １１ V.02 01-11-2010...
- Page 14 Page 14 Instructions Manual for M-16 (W347) 07/06/2017 Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate recycling bin.
Need help?
Do you have a question about the M-16 and is the answer not in the manual?
Questions and answers