Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Hubsan HT006
- Page 1 ® HT006 GPS WATCH 《HT006 User Manual 》 Version 2.0...
-
Page 2: Product Description
Product Description The Hubsan HT006 is a remote-control watch equipped with GPS. It may be paired with a Hubsan aircraft for flight and is suitable for any Hubsan equipped with a 2.4G flight control signal and GPS. Recommended flight distance is 60 meters. -
Page 3: Basic Flight Operation
Basic Flight Operation Step 1 Place the aircraft on a flat and open floor/surface, with the head facing away from the user. Step 2 Pair the watch with the aircraft. The watch must be paired with the aircraft for the units to operate properly. -
Page 4: Compass Calibration
2. Connect the aircraft to its battery; make sure the two are very close to each other. Allow the watch and aircraft to pair; the watch LEDs will stop flashing to indicate a successful pairing. 3. After the pairing is successful, aircraft and watch LEDs should be solidly lit. - Page 5 1) Horizontal calibration： Slowly rotate the aircraft on the horizontal plane. The LEDs should be flashing clockwise; proceed to step 2 when the LEDs start flashing in vertical pairs, alternately. Horizontal calibration 2) Vertical calibration： Point the head of the aircraft downwards and rotate the aircraft in place until the LEDs cease to flash and stay solidly lit.
- Page 6 Return to Home key when the aircraft is in flight. Auto Takeoff Note: Refer to the User Manuals for both the HT006 and the aircraft in use for instructions on how to use Follow Me, Orbit and other...
- Page 7 Step 6 To end the flight, choose a flat open space and press the Return to Home key. The aircraft will return to where the GPS watch is located and automatically land. Return to Home The Failsafe: The aircraft will Return to Home automatically under the following circumstances.
- Page 8 HT006 GPS Watch Components and Functions Charging status LED Micro USB port Reset button Forward Height adjustment Heading adjustment dial/Arm/Disarm dial/Follow Me Mode Right Left Backward Auto Takeoff /Return to Home Aircraft GPS status LED HT006 Power status LED Aircraft Power status LED...
- Page 9 1.Height Adjustment Dial When the dial is turned completely upwards (the dial will stop), the aircraft will rise. When the dial is turned completely downwards (the dial will stop), the aircraft will descend. When the dial is in a neutral position, the aircraft will hover without rising or falling.
- Page 10 Method 1 Method 2 After the motors are armed and spinning, there are two ways of stopping/disarming them. Method 1: When the aircraft has made a full landing, turn the Height Adjustment Dial to its most downward position and hold it there. The motors will stop after 5 seconds.
-
Page 11: Auto Takeoff
3.Auto Takeoff Long press the Auto Takeoff button for 1.5 seconds. The watch will vibrate and the aircraft will take off. The Auto Takeoff key becomes the Return to Home key when the aircraft is in flight. ● Make sure that compass calibration is successfully completed and that aircraft + watch GPS signals are stable. - Page 12 6.Photo button Press the Photo button once to take a photo. The watch will vibrate once in response. Please make sure the press is short and firm. 7.The forward, backward, left and right arrow key Use these directional arrow buttons to fly the aircraft forward, backward, left and right.
-
Page 13: Video Button
● Please make sure that the aircraft is cruising at an altitude higher than nearby obstacles (including but not limited to humans and inanimate objects). Follow Me will not function if the unit is less than 5 meters high and 5 meters away. 10.Video button Press the Video button once to begin recording video. - Page 14 Charging indicator: During the charging process, charging status LED is green. When charging is complete, the LED goes out. HT006 Power status LED: The HT006 battery is full when the green light is solid. When the low power warning is triggered, the power status LED flashes green;...
-
Page 15: Specifications
LEDs will be solidly lit. When the upgrade is in process, the LEDs will flash. 2-1.Battery HUBSAN has designed a 3.7V, 200mAh battery for the HT006 GPS watch. The unit is equipped with overcharge, over discharge and low voltage protections. - Page 16 ● Not suitable for children under 14 years of age WWW.HUBSAN.COM Product name:HT-006 GPS WATCH Product standard code：Q/HBS001-2017 Vendor: Shenzhen Hubsan Technology Co., Ltd Address: 13th Floor, Block C, Shenzhen Software Industrial Base, Xuefu Road, Nanshan District,Shenzhen, Guangdong Province, China Manufacturer: Dongguan Teng Sheng Industrial Co., Ltd.