Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Sit La Precisa 0582040
- Page 1 0582040 RF TRANSMITTER USE AND INSTALLATION INSTRUCTIONS Read the instructions before using the device. This control must be installed in compliance with current legislation SIT La Precisa S.p.A. Viale dell’Industria 31-33 35129 PADOVA - ITALY...
-
Page 2: Introduction To The Manual
Date of manufacture: : 12 - 06; Date of issue of the manual (as shown on the cover). The devices in the "582” Series are manufactured by SIT La Precisa. Any, even partial reproduction of the product, auxiliary assemblies and accompanying documentation is strictly forbidden. - Page 3 RF Remote Control See Fig. 1 and the table 1: Position of room temperature sensor LCD display ON-OFF/PILOT Key MANUAL-AUTOMATIC Key UP-DOWN arrow Key (**) FUNCTION (SLEEP-PROGRAM) Key or keyboard lock-release Base and battery compartment Note: when RF remote is associated to BIC 05844XX, where Direct Burner Ignition is present, PILOT position of the remote is equivalent to OFF position for the application. SLEEP PROGRAM SLEEP...
- Page 4 LCD Display SLEEP PROGRAM CLOCK AUTO PILOT Functioning mode symbols (MANUAL - THERMOSTATIC - PILOT). Digits identifying the weekly TIMER program currently selected. Clock setting symbol. When this symbol appears, you can adjust the clock setting displayed by the digits. Flame power bars: 1 bar = level 1, 2 bar = level 2, 3 bar = level 3, 4 bar = level 4, 5 bar = level maximum. These bars appear only in manual mode. Flame symbol, indicating the current flame power. If flame power is at level 5, the MAX message appears. Symbol for data transmission to receiver SLEEP function symbol. If this symbol does not appear, the SLEEP function is not active. If only the outline of the symbol appears, the SLEEP function is active, meaning that the appliance will switch off at the end of the countdown period set by the user and shown by symbol 17. A solid black symbol indicates that you are in the SLEEP setting menu TIMER symbol. If this symbol does not appear, the TIMER is not active. If only the outline of the symbol appears, the TIMER is active. A solid black symbol indicates that you are in the TIMER setting menu Symbols indicating the current day.
- Page 5 The temperature set by the user, that the appliance must achieve in AUTOMATIC mode. This symbol does not appear in MANUAL mode. Selectable unit of temperature measurement (Celsius – Fahrenheit). Symbol identifying room temperature measured by the built-in sensor. The temperature currently measured by the remote control’s built-in sensor from the room around the remote control. Low battery symbol. When this symbol disappears completely without flashing, the batteries must be replaced. Keypad lock symbol (lock function prevents accidental operation of buttons) Proceed with the programming according to the sequences indicated in Section "RF trasmitter configuration" (Initial Start-Up, Operating Modes) ONLY after reading the information in the following sections. Definitions Automatic mode Thermostatic: the flame level is automatically set by the remote depending on the SET room temperature and the actual room...
-
Page 6: During Operation
Initial start-up. Preliminary operations SLEEP PROGRAM Insert the 3 AAA batteries in the back battery seat (Fig. 2 and Fig. 3). CLOCK AUTO PILOT SLEEP PROGRAM SLEEP PROGRAM CLOCK CLOCK AUTO PILOT AUTO SLEEP PROGRAM PILOT CLOCK Fig. 5 Fig. 3 Fig. 4 SLEEP PROGRAM Fig. 2 SLEEP PROGRAM AUTO CLOCK CLOCK PILOT AUTO PILOT SLEEP PROGRAM... - Page 7 CLOCK CLOCK AUTO PILOT AUTO AUTO PILOT PILOT Initial start-up. Manual mode burner level selection Press and hold the "ON" button ( - Fig. 4 - ) for at least 2 seconds to enable the ignition sequence (see Section 11.5). Use the "UP"...
-
Page 8: Sleep Function
SLEEP PROGRAM Initial start-up. STANDBY level exit behaviour CLOCK SLEEP PROGRAM When the system goes back to modulation, it proceeds as follows: SLEEP PROGRAM CLOCK AUTO The system moves to level 1 and here remains for a time t (see PILOT check level... -
Page 9: Weekly Programs
Weekly Programs Weekly program Timetable N° Program Type Days Mon - Fri Householder Sat - Sun Mon - Fri Shift worker Sat - Sun Mon - Fri Shop Sat - Sun Mon - Sat Shopkeeper Mon - Sat Shopkeeper Mon - Fri Workman / Clerk Sat - Sun Mon - Fri... - Page 10 Regulatory Compliance (FCC) This equipment has been tested and found to comply with Part 15 of the FCC Rules. NOTE: Any changes or modification not approved by SIT LA PRECISA S.p.A. could void the user’s authority to operate the equipment.
- Page 11 THIS PAGE IS INTENTIONALLY LEFT BLANK...
Need help?
Do you have a question about the 0582040 and is the answer not in the manual?
Questions and answers