Lumber Jack SWL350 Safety And Operating Manual

Starter wood lathe kit

Advertisement

SAFETY AND OPERATING MANUAL
STARTER WOOD LATHE KIT
SWL350
+
ORIGINAL INSTRUCTIONS
SWL350

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SWL350 and is the answer not in the manual?

Questions and answers

Summary of Contents for Lumber Jack SWL350

  • Page 1 SAFETY AND OPERATING MANUAL STARTER WOOD LATHE KIT SWL350 ORIGINAL INSTRUCTIONS SWL350...
  • Page 2: Table Of Contents

    Closely observe all safety information in these instructions! General Power Tool Safety Warnings………………………………….…..01 Symbols & Cable Rating Chart ……….…………………………………….………04 Machine Details and Product features……….…………………………….….05 Assembly……………………………………………………………………………………..06 Operation…………………………………………………………………………………….08 Maintenance and Service…………………………………………………………….09 Lumberjack Guarantee…………………………………………………………………10 Declaration of conformity……………………………………………………………12 Parts list……………………………………………………………………………………...13 Parts Diagram………………………………………………………………………………15 SWL350...
  • Page 3: General Power Tool Safety Warnings

    A wrench or a key left c) Do not expose power tools to rain or wet attached to a rotating part of the power tool may conditions. Water entering a power tool will result in personal injury. increase the risk of electric shock. SWL350...
  • Page 4 Use power tools only with specifically operate the power tool. Power tools are designated battery packs. Use of any other dangerous in the hands of untrained users. battery packs may create a risk of injury or fire. SWL350...
  • Page 5 8 Additional Safety Warnings for Wood Lathes 8.1 Do not force the tool. Allow the tool to work as its own rate; it will do a better job this way. 8.2 Never stand on the tool. This will damage the tool. SWL350...
  • Page 6: Symbols & Cable Rating Chart

    Caution! Wear a dust mask. Amperes 7.5M 0 – 2.0 2.1 – 3.4 3.5 - 5.0 5.1 – 7.1 7.1 – 12.0 12.1 – 20.0 SWL350 SWL350...
  • Page 7: Machine Details And Product Features

    Intended Use Wood Lathe Tool Rest This product is designed with the intended 3x Turning Tools purpose of turning and polishing wood and Wrench wood like materials. It is designed for DIY applications and small craft businesses in particular. SWL350 SWL350...
  • Page 8: Assembly

    Damaged protective devices and parts must be immediately replaced by an authorised service centre. Bed Rail Connection. – Connect the two sections of the bed rail together as shown below. SWL350...
  • Page 9 – Mount the lathe to the bench using the secure the motor into position. mounting holes shown below Mounting the Work Piece – Mark the centre of your work piece at either end by drawing two lines from corner to corner. SWL350...
  • Page 10: Operation

    – Screw the work piece and driving centre onto lathe to finally finish the work piece. the headstock spindle, and then move the tailstock up to the rear end of the work piece and locate the centre to the tailstock spindle. SWL350...
  • Page 11: Maintenance And Service

    – Use a professional sharpening tool with a holder which sets angles, a fine grinding wheel for re-sharpening and a stropping wheel to polish the cutting edge. SWL350...
  • Page 12: Lumberjack Guarantee

    Authorised Dealer, you return the product at your own cost to 1.2.8 The product has been purchased by Lumberjack’s or the supplying you, as the guarantee is not transferable Authorised Dealer’s Premises - from a private sale. SWL350...
  • Page 13 Lumberjack. The claim itself should be made in a letter setting out the date and place of purchase, giving a brief explanation of the problem which has led to the claim. SWL350...
  • Page 14: Declaration Of Conformity

    SWL350...
  • Page 15: Parts List

    PARTS LIST SWL350...
  • Page 16 PARTS LIST SWL350...
  • Page 17: Parts Diagram

    PARTS DIAGRAM PART 1 SWL350...
  • Page 18 PARTS DIAGRAM PART 2 SWL350...
  • Page 19 PARTS DIAGRAM FULL SWL350...

Table of Contents