Advertisement

MOST IMPORTANT- WHEN RETURNING UNIT FOR SERVICE
1.
All units returned under warranty must be accompanied by copy of
original dated invoice. Failure to do this will incure repair charges.
2.
Please include full details of the fault.
3.
Include payment of £8 for return carriage.
4.
Send unit to: SERVICE DEPARTMENT: Pentechnic, 1 Grange
Cottages, Penkridge, Staffs ST19 5NH
                        
LIMITED ON (1) YEAR WARRANTY (UK)
This warranty gives you specific legal rights, and you may also have other rights.
TESORO/LASER assures you of the finest electronic equipment and service.
TESORO/LASER warrants that each detector manufactured by it will be free from
defects in materials and workmanship for a period of one (1) year. Should any fail-
ure to conform to the foregoing warranty appear within this period,
TESORO/LASER will, at its option, repair or replace the defective detector with-
out any charge except any transportation charges. This warranty does not cover
any detector that has been abused, tampered with, or repaired by an unautho-
rized party. This warranty applies only to units purchased from AUTHORIZED
UK DEALERS. This warranty excludes batteries, damage caused by leaking bat-
teries, cable faults due to flexing on body mount units, and wear of the search coil
housing. Complete, detach and mail the portion below within 10 days of purchase
in order to activate your warranty. Send the WARRANTY to : TREASURE
WORLD, 192 Albany st. LONDON NW1 4AP.
Cut along this line
━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━ ━
MODEL
DATE
PURCHASER'S NAME
ADDRESS
Where did you first learn of TESORO/LASER products?
What made you decide to buy TESORO/LASER?
Purchased where?
What do you like or dislike about the product?
SERIAL No.
OPERATOR INSTRUCTION MANUAL
LASER METAL DETECTORS
192 Albany Street
London, NW1 4AP
Telephone 207-387-3142

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Rapier II and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Laser Rapier II

  • Page 1 This warranty gives you specific legal rights, and you may also have other rights. TESORO/LASER assures you of the finest electronic equipment and service. TESORO/LASER warrants that each detector manufactured by it will be free from defects in materials and workmanship for a period of one (1) year. Should any fail-...
  • Page 2 GENERAL INFORMATION INDEX OF COMMON QUESTIONS What does the factory include with my detector? See UNPACKING THE BOX on page 6. How do I put my detector together? See ASSEMBLING YOUR DETECTOR on pages 8-9. How do I install a new battery? See INSTALLING THE BATTERY on page 7.
  • Page 3 “built-in accessories” are simply unnecessary in a Rapier II detector. The power and features of the Laser Rapier II make it an ideal detector for a beginner who wants a machine they will never outgrow. It is also ideal for the serious detectorist who wants...
  • Page 4: Table Of Contents

    GENERAL INFORMATION LASER RAPIER II OPERATOR INSTRUCTION MANUAL ☑ The searchcoil cable is hard wired to the searcoil and protected by a CONTENTS strain relief. Inspect the strain relief frequently to make sure it is firmly attached and intact. ☑...
  • Page 5: General Information

    Basic Care Recognizing false signals in Discriminate Mode ....Pinpointing a Target............19 The Rapier II is a sturdy instrument, but it is not designed to withstand abuse. In caring for your Rapier II, there are several important Recovery ................19 “DO NOTs” to remember. DO NOT use it to pry rocks loose or to beat Specifications..............20...
  • Page 6: Introduction

    Complete instructions on how to op- erate the Rapier II are found in the two main sections: GETTING STARTED and OPERATING TECHNIQUES. If you are new to metal detecting, we highly recommend read- ing and following the entire GETTING STARTED section to develop the “feel”...
  • Page 7: General Description

    The Rapier II has features that make its power easy to use. The again. Any soil remaining on the surface should be brushed into the grass factory preset ground rejection circuitry allows “turn-on-and-go”...
  • Page 8: Getting Started Unpacking The Box

    DISC LEVEL is set to reject pull tabs on any padded arm bracket and control housing. metal detector that is a TR Discriminator like the Rapier II. If you don’t 1 Middle Pole Assembly With Pole Lock dig any junk at all, you are surely passing up a lot of good finds as well.
  • Page 9: Installing The Battery

    In rough and rocky areas, it is best not to “scrub” Your Rapier II is equipped with an automatic battery test circuit the coil on the ground, as the rocks will act like abrasives, and wear away so that you can always be sure you are getting top performance.
  • Page 10: Assembling Your Detector

    This mo- Install the thumb nut on the mounting screw and tighten by hand. tion is called a “sweep.” The Rapier II was designed to get maximum depth without the frantic pace required of earlier motion detectors, so go (NOTE: Do not overtighten the thumb nut.
  • Page 11 LASER RAPIER II OPERATOR INSTRUCTION MANUAL GETTING STARTED The DISC LEVEL should be set to your desired “rejection level” Slide lower pole into middle pole until spring buttons click into for the particular area you are searching. We recommend starting at a the first set of adjustment holes.
  • Page 12: Adjusting The Pole & Searchcoil

    OPERATING TECHNIQUES LASER RAPIER II OPERATOR INSTRUCTION MANUAL Setting the Sensitivity Level in MAXBoost ADJUSTING THE POLE & SEARCHCOIL The pole length should be adjusted so that the detector does not The MAXBoost feature is a high gain boost over and above the become uncomfortable or tiring after long periods of use.
  • Page 13: Operating Techniques

    OPERATING TECHNIQUES CONTROLS Since the most troublesome adjustments of standard detectors have been automated in the Rapier II, Tuning this detector is simply a The Rapier II has only five controls, all mounted on the front matter of: panel of the housing for fingertip adjustment. How these controls should ➊...
  • Page 14: Disc Level Control

    Controlling Audio Volume The TONE switch is used to select the audio tone for the detec- The speaker in the Rapier II does not have a volume control. tor. Selecting LOW will give the audio a lower tone. Selecting HIGH The volume should be sufficient to accurately hear the target response will give the auido a higher tone.

Table of Contents

Save PDF