Summary of Contents for MX Options Solo QI
- Page 1 Instantaneous Electric Shower Installation Instructions IMPORTANT! This Step-by-Step guide should be given to the customer after installation and demonstration.
-
Page 2: Contents & Features
CONTENTS & FEATURES 1. PLEASE READ THIS IMPORTANT SAFETY INFORMATION Products manufactured by the MX Group are safe • 4. Riser Rail • 2. Showerhead Bracket and without risk provided they are installed, used and QUICK INSTALLATION • 3. Riser Rail Tube maintained in good working order in accordance with our a guide for installers instructions and recommendations. - Page 3 1. PLEASE READ THIS IMPORTANT SAFETY INFORMATION (CONT.) IMPORTANT: Turn the Temperature control knob anticlockwise until the valve is fully open before switching on the unit. This will ensure a fast fill up of the unit IMPORTANT: This appliance is not intended for use by persons (Including children) when the shower is first switched on.
- Page 4 USE THE FOLLOWING CHECK LIST TO AID YOUR INSTALLATION 2. IMPORTANT n Shower Installation must be carried out by a n The shower unit must not be fitted where it may 1. Check that the water supply will satisfy requirements ........suitably qualified person and conform with IEE be exposed to frost, for example in an outdoor area.
-
Page 5: Installation
4. GENERAL LAYOUT OF A SHOWER INSTALLATION 5. INSTALLATION A TYPICAL INSTANTANEOUS ELECTRIC SHOWER Avoid connecting the shower unit, if possible, Position your shower unit on the wall away from the Place the shower unit on the wall and mark the INSTALLATION were it will be affected by water drawn off by other direct spray of the shower and at about the same... -
Page 6: Plumbing Connections
6. PLUMBING CONNECTIONS PLUMBING CONNECTIONS Water inlet direction option Turn off the water supply at the isolating stop tap. Having determined the direction of the inlet water NOTE! The shower unit is supplied for right hand installation. The 8 arrows depict water Location holes for supply: Top (falling), Bottom (rising), or Back inlets. - Page 7 7. ELECTRICAL CONNECTIONS ELECTRICAL SPECIFICATIONS The diagram below shows the route of the cable into The diagram right shows a schematic wiring the shower unit for connection to the terminal blocks, diagram. Nominal Power rating at 240V Nominal Power rating at 230V connect as follows: 7.5kW - (32A MCB rating) 6.9kW - (32A MCB rating)
-
Page 8: Riser Rail Fitting Instructions
9. RISER RAIL FITTING INSTRUCTIONS 10. COMMISSIONING THE SHOWER 1. Establish position for the riser rail, and mark 1. Make sure that the electrical supply has been 9. Now turn the top power selector knob to the the wall for the lower mounting bracket. Make isolated at the double pole isolating switch. -
Page 9: Operating The Shower
11. OPERATING THE SHOWER 12. SHOWERHEAD CLEANING INSTRUCTIONS 1. Switch on pull-cord or wall mounted switch. 5. If necessary turn bottom ‘Temperature’ The showerhead should be cleaned periodically to remove limescale or debris which will control knob slowly to obtain desired reduce the performance of the shower. -
Page 10: Faq's - Frequently Asked Questions
13. FAQ’S - FREQUENTLY ASKED QUESTIONS Q. Water does not flow when turned on. Q. Water too cool or cold. Q. The shower hose or showerhead is damaged, Q. Power setting will not remain on the setting I have leaking or otherwise unsatisfactory. selected. -
Page 11: Service Policy
14. THE MARLETON CROSS LTD (MX GROUP) - 2 YEAR GUARANTEE 15. SERVICE POLICY Marleton Cross Limited (MX Group) hopes you are satisfied with your Limitations In the event of you needing to contact the MX Group 3. If a service call is booked, you or a representative purchase and in the unlikely event that you encounter a problem which Customer Care Department, the following procedure must be present during the Engineers visit. - Page 12 NOTES NOTES...
- Page 13 Marleton Cross Limited Trading as The MX Group Alpha Close, Delta Drive, Tewkesbury Industrial Estate, Tewkesbury, Gloucestershire GL20 8JF Tel: 01684 293311 Fax: 01684 293900 Email: sales @ mx-group.com www.mx-group.com CUSTOMER CARE: 0845 5052211 TRADE DESCRIPTIONS ACT Variations in terms of colour finish, materials and all other aspects of appearance may occur on occasions, either through non-availability of materials or due to our policy of continuing technical improvement.
Need help?
Do you have a question about the Solo QI and is the answer not in the manual?
Questions and answers
Why does my electric shower alternate from hot to cold and back again while the shower is running.
The MX Options Solo QI electric shower may alternate between hot and cold water due to water pressure fluctuations. If the water pressure falls below the minimum required level, the stabiliser valve may not maintain a constant temperature. This can happen if water is being drawn off at other points in the building. Additionally, seasonal temperature variations can affect the water temperature on the same setting. Ensuring the showerhead and filter are clean can also help maintain consistent performance.
This answer is automatically generated