Speaks z wave SP814 User Manual

SP814 MOTION DETECTOR
TM
The Motion Detector is a Z-Wave
TM
any Z-Wave enabled network.
TM
Z-Wave logo can also be used with it regardless of the manufacturer, and ours
can also be used in other manufacturer's Z-Wave
Motion Detector can control our modules via controller setting. Inclusion of this
Motion Detector on other manufacturer's Wireless Controller menu allows
remote turn-on of connected modules and their connected lighting when the
TM
detector is triggered. Z-Wave
they support that function.
The Motion Detector is designed with two detecting sensors, Passive Infra-Red
(PIR) sensor and light sensor, in order to fulfill the purpose of security and home
automation. When the detector is cooperated with security appliances, it is
acting as a security device by detecting changes in infra-red radiation levels. If
a person moves within or across the device field of vision, a trigger radio signal
will be transmitted to cause full alarm condition in order to frighten intruders away.
Alternatively, when the detector is worked with home automation appliances, the
detector can be set to perform the role of home automation device by detecting
both changes in infra-red radiation levels and percentage of lux levels. Once
night falls, the percentage of ambient illumination is lower than preset value. If
a person moves within or across the device field of vision, a trigger radio signal
will be transmitted so as to turn on the connected lightings for better illumination.
Two mounting methods are provided for varying detection range. The detector
can be mounted on a wall for farther detecting distance but narrower coverage;
while for ceiling mounting, shorter detecting distance can be made but desired
coverage can be expected at user's disposal.
Product Overview
3
1
Front View
1
Lens Cover (wall-lens cover and ceiling-lens cover)
2 4
Photocell Sensor
3 5
PIR Sensor
enabled device which is fully compatible with
TM
Z-Wave enabled devices displaying the
TM
enabled networks. This
nodes in the system also act as repeaters if
2
4
Rear View
Inside View
Two-Color Indication LED (red & green)
Learning Key
Adding to Z-Wave
In the rear casing, there is a learning key which is used to carry out inclusion,
exclusion or association.
inclusion/exclusion/association mode, and press the learning key on the
detector 3 times within 1.5 seconds, the detector beeps whenever you press the
learning key.
Auto Inclusion
Besides carrying out the inclusion procedure by pressing the learning key, the
detector executes the function of auto inclusion when...
1. The power is first supplied where no ID code has been stored in the detector.
The orange LED flashes on and off alternatively and repeatedly at 2-second
intervals.
2. The execution of exclusion/reset is successful where the stored ID code(s) is
(are) cleared.
Note: The node information of explorer frame will be emitted once every 5
seconds during 4 minutes auto inclusion until the inclusion process is complete.
The detector cannot execute detecting function if no ID code has been stored in
it.
Refer to the following table for functions indication and operation:
Function Description
No node ID The Z-Wave Controller does not allocate a
node ID to the unit.
Inclusion 1.
2. Pressing learning key 3 times within 1.5
Exclusion 1.
2.
Reset 1.
2.
5
3.
1
TM
Network
TM
Put a Z-Wave Wireless
Have Z-Wave Controller entered
inclusion mode.
seconds will enter inclusion mode.
Have Z-Wave Controller entered
exclusion mode.
Pressing learning key 3 times within 1.5
seconds will enter exclusion mode.
Press learning key 3 times within 1.5
seconds.
Within 1 second, press and hold learning
key for 5 seconds until LED is OFF.
IDs are cleared and all settings will be
reset to factory default.
Controller into
Indication
2-second on, 2-second
off
One short beep when
learning key is pressed
One short beep when
learning key is pressed
One short beep when
learning key is pressed
One long beep for 5
seconds
2-second on, 2-second
off (for 4 minutes)