Page 2
-1 ± This equipment complies with the essential requirements of the Directive 1999/5/EC Radio and Telecommunications Terminal Equipment Directive. NOTE This device contains electrostatically sensitive components. Damage can occur to these components if the appropriate handling is not adhered to. ESD Handling precautions: A working area in which Digital Cellular Telephones may be safely handled without undue risk of damage from electrostatic discharge must be available.
TABLE OF CONTENTS SECTION 1 Specifications ……………………………………………………… (see Cover sheet) SECTION 2 General Descriptions 2.1 Multi Band ………………………………………………………. 04 2.2 Radio Frequency Power Level ……………………………….. 05 2.3 Speech Codec …………………………………………………. 05 2.4 Languages ………………………………………………………. 05 2.5 Battery Charging ……..………………………………………… 06 2.6 Battery Safety ……………………………………………………...
900MHz and 1800MHz, Dual band networks can provide major benefits in terms of capacity enhancement and revenue optimisation through the introduction of new services. The CMD-Z7 is a phase II, GSM900 class 4, GSM1800 class 1 mobile phone. The nominal maximum output power for GSM900 is 2W, for GSM1800 1W.
40 W (46 dBm) 20W (43 dBm) max. MS-Power 2 W (33 dBm) 1W (30 dBm) 2.3 Speech Codec The CMD-Z7 supports the following speech codecs. • Full Rate (FR) Codec • Half Rate (HR) Codec • Enhanced Full Rate (EFR) Codec The speech codec forms the human voice into a digital signal, which is sent in the GSM network.
2.5 Battery Charging There is no charging circuitry in the battery pack. The CMD-Z7 has complete charger function internally. The telephone can be charged only with the battery connected the phone. This situation can be sub-divided into two situations: the phone is on or off. It can be charged with the AC Adapter, Travel Charger or Cigar Lighter Charger.
OPERATING INSTRUCTIONS 3.1 The Basic Features of the CMD-Z7 • Parts and Controls This section provides a brief guide to the operation and facilities available on the CMD-Z7. Refer to the Operating Manual for full operational information. Clear Key Ear piece...
• Loudspeaker v During a call, press the Jog Dial backward and select Loudspeaker to turn the loudspeaker on/off. • The Voicemail Key v Press and hold to access your Voicemail • Manner Mode v In standby mode when the flip is closed, press the Jog Dial backward to activate/deactivate the manner modes.
SECTION 4 DISASSEMBLY IMPORTANT NOTE : The IMEI number is the electronic identification of the hardware, which is stored electronically. There should be no discrepancy between the number on the sticker and the number within the set memory allowed. In case of replacing the lower cabinet it is to make sure that the IMEI Sticker mounted on the lower case (visible from the battery compartment) will be replaced to the new housing part as well.
Page 12
FLEX KEY MOUNT, ASS’Y FRAME LCD, ASS’Y )5$0( /&'$66< Note 1: Certain repairs may require that the /&' 02'8/( has to be detached from the )5$0( /&'$66< Note 2: On reassembly the must be placed /&' 02'8/( *8,'( /&'$66< after the and the have *8,'( .(<...
Page 13
GUIDE, KEY SUPPORT & ANTENNA CABINET LOWER Re-assembly procedure : To re-assemble the unit, apply the reverse order of the above mention disassembly procedure.
4.2 Interface to GSM-Tester Test Set Up for CMD-Z7 Level 1 Testing CMD- Z 7 Battery Pack Test SIM Card Service Test Connector RF output : SMA jack STC-05 Part No. 3-235-700-01 RF input Connector GSM – TESTER This unit acts as a base station providing...
Level Test Procedure with GSM TESTER recommendation: • Simulate GSM call processing – to check the functionality of transmitting and receiving audio signals of loudspeaker and microphone. • Basic GSM transmission & reception parameter testing – to ensure that handset’s performance compiles with standard GSM specification.
• Copy all the files to the PC (define own directory). • Connect the Data Transfer Jig to the PC COM-port (COM 1 or COM 2) and the CMD-Z7 external connector. • Insert a test SIM in the CMD-Z7; this is because during the procedure the Flash Loader will attempt to perform data control operations, which are not generally permitted by original SIMs.
• Click on “Get Data”. • Now the program runs automatically (if the application does not start after a while, press any key of the CMD-Z7) • After the read data is downloaded, either reload it in another mobile (reconnect a new mobile and click on “Write Data”) or save it on the disc using File/Save option.
SECTION 6 SPARE PARTS AND ACCESSORIES LIST 6.1 Spare Parts Note: • The parts with no reference in the exploded view are not supplied. 5HI 1R 3DUW 1R 'HVFULSWLRQ 5HPDUN 5HI 1R 3DUW 1R 'HVFULSWLRQ 5HPDUN A-3649-351-A &$%,1(7 )/,3 1-815-605-21 5) &2$;,$/ &211(&725 %$'*( 35,17,1* 1-815-308-21 &211(&725 %$77(5<...
Need help?
Do you have a question about the CMD-Z7 and is the answer not in the manual?
Questions and answers