Chapter 3 AMI BIOS Setup ....................22 Overview ........................22 Main Menu ......................23 Ad vanced Menu ....................24 Power Menu......................34 Security Menu .......................35 Boot Menu......................36 Save & Exit Menu ....................37 Chapter 4 Driver Installation .....................39 UbiQ-100 Series User’s Manual...
Tables Tables Table 1 UbiQ-100 Series Specification ..............13 Table 2 UbiQ-100 Series BIOS Main Menu............23 Table 3 Advanced Menu ..................24 Table 4 Advanced Menu – Display Configuration..........25 Table 5 Advanced Menu – Super IO Configuration..........26 Table 6 Advanced Menu – Super IO Configuration – Serial Port 1 Configuration ....................26...
The product chassis may be hot when the system is working. Please do not touch the surface before turn off the system power and wait for about 5 minutes until the system cools down. UbiQ-100 Series User’s Manual...
Also, before connecting a cable, make sure both connectors are correctly oriented and aligned. CAUTION Do not attempt to service the system yourself except as explained in this user’s guide. Follow installation and troubleshooting instructions closely. UbiQ-100 Series User’s Manual...
Handle components and boards with care. Don’t touch the components or contacts on a board. Hold a board by its edges or by its metal mounting bracket. Do not handle or store system boards near strong electrostatic, electromagnetic, magnetic, or radioactive fields. UbiQ-100 Series User’s Manual...
Do not dispose of lithium batteries in domestic waste. Dispose of the battery according to the local regulations dealing with the disposal of these special materials (e.g. to the collecting points for disposal of batteries) UbiQ-100 Series User’s Manual...
(take adequate measures) at their own expense. The user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. UbiQ-100 Series User’s Manual...
Buildings in which climate is controlled usually maintain an acceptable level of humidity for system equipment. However, if a system is located in an unusually UbiQ-100 Series User’s Manual...
Page 11
Surge protectors should be used with all UPS systems, and the UPS system should be Underwriters Laboratories (UL) safety approved. UbiQ-100 Series User’s Manual...
Chapter 1 Introduction Overview UbiQ-100 Series is a fanless IoT gateway integrating Intel® BayTrail Atom™ E3815/E3825 / Celeron® N2930 SoC Processor into a small footprint. Combining two GbE LAN ports and two mPCIe slots for wireless expansion, it enables flexible connections between edge devices and data center through the wired or wireless networks.
The user-defined LED can be configured by the user via SoC GPIO. Micro SD Card Cage The Micro SD Card Cage provides users with expandable memory space suitable for multimedia file retrieval, including images, animations and movie UbiQ-100 Series User’s Manual...
Page 15
The USB (Universal Serial Bus) port is compatible with USB devices such as keyboards, mouse devices, cameras, and hard disk drives. USB allows many devices to run simultaneously on a single gateway, with some peripheral acting as additional plug-in sites or hubs. UbiQ-100 Series User’s Manual...
The USB (Universal Serial Bus) port is compatible with USB devices such as keyboards, mouse devices, cameras, and hard disk drives. USB allows many devices to run simultaneously on a single gateway, with some peripheral acting as additional plug-in sites or hubs. UbiQ-100 Series User’s Manual...
Setting up your gateway Connect USB mouse & keyboard Your UbiQ-100 Series does not come with a keyboard and mouse connector, but you can use any USB keyboard or mouse to connect with your gateway. USB 3.0 USB 2.0 Figure 4 Connect USB mouse &...
Chapter 2 Connect LAN port Connect one end of a network cable to the LAN port on the gateway rear panel and the other end to a hub or switch. RJ45 Figure 5 RJ45 connector UbiQ-100 Series User’s Manual...
Chapter 2 COM Ports COM ports with the pin definitions. COM1 & COM2 RS-232/422/485 Port D-SUB 9P RS-232 RS-422 Half Duplex Full Duplex RS-485 RS-485 DATA- DATA+ Figure 6 COM ports UbiQ-100 Series User’s Manual...
Connect the power cable to the power adapter Connect the power cable to a power outlet Press the power button on the front panel to turn on the gateway DC Jack Power Button Figure 7 Turning on the gateway UbiQ-100 Series User’s Manual...
It is possible for the CMOS battery to fail, which will cause data loss in the CMOS only. If this happens you will need to reconfigure your BIOS settings. UbiQ-100 Series User’s Manual...
Menu provides System Overview information and allows you to set the System Time and Date. Use the “<” and “>” cursor keys to navigate between menu screens. Table 2 UbiQ-100 Series BIOS Main Menu BIOS SETUP UTILITY A d v a n c e d...
F4: Save & Reset ESC: Exit Version 2.17.1249. C opyright (C) 2016, American M egatrends, Inc. EIST Options: Disabled, Enabled Limit CPUID Maximum Options: Disabled, Enabled Execute Disable Bit Options: Disabled, Enabled Intel ® Virtualization Tech Options: Disabled, Enabled UbiQ-100 Series User’s Manual...
Enter: Sel ect +/-: Change Opt. F1: General H elp F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit Version 2.17.1249. C opyright (C) 2016, American M egatrends, Inc. Network Stack Options: Disabled, Enabled UbiQ-100 Series User’s Manual...
ESC: Exit +VIN : +12.268 V : +5.066 V +VMEM : +1.349 V Version 2.17.1249. C opyright (C) 2016, American M egatrends, Inc. CPU Warning Temperature Options: Disabled, 80 C, 85 C, 90 C, 95 C UbiQ-100 Series User’s Manual...
Resume By LAN De vice Options: Disabled, Enabled Resume By PCI-E Device Options: Disabled, Enabled Resume By Ring De vice Options: Disabled, Enabled Resume By RTC Alarm Options: Disabled, Enabled WatchDog Timer Configuration [Disabled] WDT Function ■ Options: Disabled, Enabled UbiQ-100 Series User’s Manual...
> Secure Boot menu F4: Save & Reset ESC: Exit Version 2.17.1249. C opyright (C) 2016, American M egatrends, Inc. Secure Boot menu Secure Boot [Disabled] Options: Disabled, Enabled Secure Boot Mode [Custom] Options: Standard, Custom UbiQ-100 Series User’s Manual...
Full Screen LOGO Display Options: Disabled, Enabled Bootup Numlock State Options: On, Off CSM Support Options: Disabled, Enabled Boot Option Filter Options: UEFI and Legacy, Legacy only, UEFI only Boot Option #1 Options: Windows Boot Manager, Disabled UbiQ-100 Series User’s Manual...
+/-: Change Opt. Save C hanges F1: General H elp Discard Changes F2: Previous Values F3: Optimized Defaults Restore Defaults F4: Save & Reset ESC: Exit Version 2.17.1249. C opyright (C) 2016, American M egatrends, Inc. UbiQ-100 Series User’s Manual...
Page 38
Load Optimal Default values for all the setup values. This option allows you to load failsafe default values for each of the parameters on the Setup menus, which will provide the most stable performance settings. The F8 key can be used for this operation. UbiQ-100 Series User’s Manual...
You can download the drivers for the UbiQ-100 Series from the our website and install as instructed there. For other operating systems, please contact us.