Advertisement
Quick Links
New Upholstered Space Saving and Ottoman Bed Range
Beds: Harrow, Hornsey, Ludlow, Minster, Richmond, Ripley, Stockport, Woking
PLEASE READ THE USER GUIDE BEFORE FOLLOWING THESE INSTRUCTIONS
Please spend time reading these instructions and reading our assembly instructions online before
constructing or moving your bed.
Please make sure that all the surfaces that you lean any of our products on are clean and soft so
as not to mark or damage the bed.
Please ensure that you wash your hands or that your gloves are very clean even after and during
unwrapping the products, to not mark the finished product in any way. We wish you to have an
excellent clean Warren Evans bed!
1.
When unwrapping these beds please keep all the wrapping intact should it be needed for
returns. Make a space in your bedroom for where the bed will actually be positioned.
Start the assembly process by leaning the head end against the wall of choice.
2.
Open the 3 largest boxes, one of which contains both the foot end and the head end of the
bed (this box also contains screws, bolts and allen key inside).
Place the head end on its feet leaning against your wall of choice. Place the foot end on its
feet to one side. (Do not slide the headboard onto the head end until instructed to do so).
3.
There are 12 bolts, 3 that go in each of the legs. Put each bolt in but only one full turn so
that it's loosely connected.
Assembly Guide
(including all Ottoman versions)
Head End
Bolts x 12
Advertisement
Related Manuals for Warren Evans Harrow
Summary of Contents for Warren Evans Harrow
- Page 1 Assembly Guide New Upholstered Space Saving and Ottoman Bed Range Beds: Harrow, Hornsey, Ludlow, Minster, Richmond, Ripley, Stockport, Woking (including all Ottoman versions) PLEASE READ THE USER GUIDE BEFORE FOLLOWING THESE INSTRUCTIONS Please spend time reading these instructions and reading our assembly instructions online before constructing or moving your bed.
- Page 2 If there is a metal ottoman lifting mechanism, this must go at the head end of the bed. Make sure the exterior of the side (A) overlaps the head end (B). Make sure that the sides of the bed are Hook the bracket (C) over the bolts (D), one facing up side at a time, onto the headboard first.
-
Page 3: Aerial View
Now using just your fingers tighten all 12 bolts as much as possible all the way around all 4 legs. AERIAL VIEW Head End Head End Foot End Foot End Shown here is an aerial view looking down on your bedframe, please ‘square it up’ so that it is not ridiculously out of kilt. - Page 4 If you have an ottoman bed with metal hinges, go to assembly step If you do not, continue to step...
- Page 5 If your bed is a super king size or a small super king size (6ft or 5ft 6inch wide) you will need to insert the centre beam. Centre beam Centre beam...
- Page 6 Open the plastic wrapped set of slats and space them on the bed frame as shown. Screw down both ends of the slat at the head end first. Do the same with the foot end slat. Do the same with the “middle slat” (see arrows).
- Page 7 DISASSEMBLING: FOR BEDS WITHOUT OTTOMANS To disassemble, reverse the order of the assembly instructions, but first number the slats (1, 2, 3, 4, 5 etc...) as shown so that they screw back into the same places when reassembling. Make sure hands and surfaces are clean and all of the parts of the bed do not get damaged against rough or hard surfaces.
- Page 8 If you have an ottoman bed please continue here from step Unwrap the lightest long package carefully. There are 3 cross beams (A), a slat with ply support (B) and a slat with a handle in (C) will be used later). Head End Foot End ottoman base...
- Page 9 If your bed is a super king size or a small super king size (6ft or 5ft 6inch wide) you will need to insert the centre beam. Take the 2 slats (head end and foot end) that are available and place them onto the bed as shown.
- Page 10 Please space the foot end slat appropriately and screw down all 4 screws, and now do the same with the head end slat. Please continue the same process with all of the other slats, which are in the last package to be opened. Please spread these slats out so that they are equally spaced in between the first and last slat.
- Page 11 IMPORTANT: LAST STEP OF YOUR BED ASEEMBLY The 2 hoop-lock screws at the foot end of each side of the bed must be completely unscrewed and then screwed back in 4 turns to keep it conveniently located for use whenever your bed is to be moved. Failure to remove far enough before use could scratch the stationary side rail and damage it.
Need help?
Do you have a question about the Harrow and is the answer not in the manual?
Questions and answers