Related Manuals for I-Tech IP67 Aluminum
Summary of Contents for I-Tech IP67 Aluminum
-
Page 1: User Manual
Full IP67 Aluminum WRD Rugged PC Series User Manual Version 1.0 i-Tech Company LLC TOLL FREE: (888) 483-2418 • EMAIL: info@itechlcd.com • WEB: www.iTechLCD.com... -
Page 2: Safety Information
19” Full IP67 Rugged PC User’s Manual Safety Information WARNING! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. - Page 3 19” Full IP67 Rugged PC User’s Manual • If any of the following situations arises, get the equipment checked by service personnel: The power cord or plug is damaged. Liquid has penetrated into the equipment. The equipment has been exposed to moisture. ...
-
Page 4: Table Of Contents
19” Full IP67 Rugged PC User’s Manual Contents Contents ........................3 Introduction ........................4 Features ............................... 4 Package Contents ..........................5 Product Overview..........................6 Getting Started ......................7 Turning On Your Device ........................7 Adjusting the LCD Display Brightness ....................8 Calibrating Touch Screen ........................9 Turning Off Your Device ........................ -
Page 5: Introduction
19” Full IP67 Rugged PC User’s Manual Introduction i-Tech's WRD Series consists of rugged and unusually well-sealed vehicle or stationary-mount Panel PCs available in a wide variety of configurations. Depending on the intended application, WRD panels have been available with 5-wire resistive touch displays measuring 8.4, 10.4, 12.1 or 15-inches diagonally. -
Page 6: Package Contents
19” Full IP67 Rugged PC User’s Manual Package Contents Before using this Panel PC, please make sure that all the items listed below are present in your package: Panel PC AC to DC adapter Power cord USB cable USB adapter Ethernet cable Ethernet extension RS-232 cable... -
Page 7: Product Overview
19” Full IP67 Rugged PC User’s Manual Product Overview Front View Touch Display Front Button & LED Indicators Side and Rear Views Front Button Button Type Function Power on/off Increase the brightness of the Panel Decrease the brightness of the Panel Suspend the touch’s function temporarily Programmable function key configured by Hot Tab Utility... -
Page 8: Getting Started
19” Full IP67 Rugged PC User’s Manual Getting Started Turning On Your Device 1. Remove the protective cap of the DC IN jack. 2. Connect the AC adapter to the power cord. 3. Plug the power cord to an electrical outlet. 4. -
Page 9: Adjusting The Lcd Display Brightness
19” Full IP67 Rugged PC User’s Manual Adjusting the LCD Display Brightness Tap the arrow on the system tray to display the hidden icons. Double-tap the icon to display the brightness menu. Drag the brightness bar to adjust the brightness level according to your preference. -
Page 10: Calibrating Touch Screen
19” Full IP67 Rugged PC User’s Manual Calibrating Touch Screen When turning on the Panel PC for the first time, it is highly recommended to calibrate the touch screen to ensure touch accuracy. Five-wire resistive touchscreens The five-wire resistive touchscreens use a glass panel with a uniform resistive coating. A thick polyester coversheet is tightly suspended over the top of the glass, separated by small, transparent insulating dots. - Page 12 19” Full IP67 Rugged PC User’s Manual Elo Touch Correction i-Tech ELO Touch driver software provides a consistent software interface among all ELO touch screens and controllers. Go to http://www.elotouch.com/Support/dnld.asp for a complete list of available supports. After the driver installation is complete, do the following to perform touch screen calibration.
- Page 13 19” Full IP67 Rugged PC User’s Manual 4. Follow the on-screen instructions to calibrate the touch screen. 5. Tap the icon if the cursor follows your finger to finish and exit the calibration utility.
-
Page 14: Turning Off Your Device
19” Full IP67 Rugged PC User’s Manual Turning Off Your Device To shut down your device, do the following: Tap Start ( ) > Shut down. Wait for your Panel PC to completely turn off before disconnecting the power cord (if necessary). -
Page 15: Installation
19” Full IP67 Rugged PC User’s Manual Installation Wiring Requirements The following common safety precautions should be observed before installing any electronic device: • Strive to use separate, non-intersecting paths to route power and networking wires. If power wiring and device wiring paths must cross make sure the wires are perpendicular at the intersection point. -
Page 16: Connecting The Interface
19” Full IP67 Rugged PC User’s Manual Connecting the Interface The unit is available with different pass through IP67 connector for cable connections (required to maintain enclosure protection rating). These IP67 connectors are water and gas tight and must be tightened with a torque described in the gland manufacturer’s instructions provided with the unit. -
Page 17: Usb Port
19” Full IP67 Rugged PC User’s Manual COM Port Signal Name Signal Name USB Port Signal Name LAN1 Port Signal Name Signal Name MDI0_IN+ MDI0_IN- MDI1_IN+ MDI2_IN+ MDI2_IN- MDI1_IN- MDI3_IN+ MDI3_IN- Power terminal block Signal Name COM Port Signal Name Signal Name... -
Page 18: Mounting Solution
19” Full IP67 Rugged PC User’s Manual LAN2 Port Signal Name Signal Name MDIO3- MDIO3+ MDIO2- MDIO2+ MDIO1- MDIO1+ MDIO0- MDIO0+ USB Port Signal Name Note • This adapter was certified by UL, CUL TUV/GS CE, FCC, BSMI, EK, DOIR+C- TICK, CCC, PSE. - Page 19 19” Full IP67 Rugged PC User’s Manual Rear Mount Before you start installing the rear mount, be sure that you have the following components: 19” Stainless Steel LCD 2 x Bracket M4, 4mm Screws To install the rear mount, perform the following: 1.
- Page 20 19” Full IP67 Rugged PC User’s Manual 2. Screw the brackets on both sides of your device. 3. Secure the display from the back side first, so the outer frame can be fully covered to ensure the safety of your display.
- Page 21 19” Full IP67 Rugged PC User’s Manual 4. Make sure your screws are tight and on the right position.
-
Page 22: Specification
19” Full IP67 Rugged PC User’s Manual Specification Hardware Specifications Item Specifications Computer Intel i5-4300u turbo Max 2.9GHz Windows 7 embedded systems System Chipset Intel® HD graphics 5000 Bios AMI 16Mbit Flash System Memory 8GB capacity, 4GB pre-installed 3 x USB 3.0 Storage Storage Support Removable 128GB industrial grade SSD to store OS;... - Page 23 19” Full IP67 Rugged PC User’s Manual Item Specifications Physical Characteristics Housing Stainless steel Dimensions 396 x 310 x 49mm (W x H x D) Mounting Mounting hole for VESA 100 x 100, yoke mounting Environment Limits Operating Temperature -40°C to 60°C Storage Temperature -40°C to 80°C Ambient Relative Humidity...
-
Page 24: Appendix
19” Full IP67 Rugged PC User’s Manual Appendix Appendix A: Cleaning the Monitor Before cleaning: • Make sure the device is turned off. • Disconnect the power cable from any AC outlet. When cleaning: • Never spray or pour any liquid directly on the screen or case. •... -
Page 25: Appendix B: Statement Of Regulatory Approval
19” Full IP67 Rugged PC User’s Manual Appendix B: Statement of Regulatory Approval Refer the following descriptions for various approvals and certifications Low Voltage Directive European Safety for Industrial Control Equipment Self-Declaration in accordance with European LVD Directive 2006/95/EC; Independent 3rd party assessment (Accredited by IEC 17025) Electromagnetic Compatibility Directive European EMC for Industrial Control Equipment...