TEAC SERVICE MANUAL C T - M 8 0 9 S V 1. Caution…………………………………………………………..2 2. Specification……………………………………………………..6 3. BOM List ……………………… ……………… ………………...9 4. Alignment Procedure………………………………………….…42 5. Block Diagram……………………………………………………46 6. Schematic Diagram………………………………………………47 7. PCB Layout………….……………………………………………48 This manual is the latest at the time of printing, and does not include the modification which may be made after the printing, by the constant improvement of product.
Page 2
CAUTION: Use of controls, adjustments or procedures other than those specified herein may result in hazardous radiation exposure. CA UTION: TO REDUCE THE RISK OF CAUTION ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE RISK RISK OF OF ELECTRI ELECTRIC C PARTS INSIDE.
IMPORTANT SAFETY INSTRUCTIONS CAUTION: Read all of these instructions. Save these instructions for later use. Follow all Warnings and Instructions marked on the audio equipment. 1. Read Instructions- All the safety and operating instructions should be read before the product is operated. 2.
Page 4
PROTECTION AND LOCATION OF YOUR SET Do not use this television set near water ... for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. Never expose the set to rain or water. If the set has been exposed to rain or water, unplug the set from the wall outlet and refer servicing to qualified service personnel.
Page 5
OPERATION OF YOUR SET 18. This television set should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply at your home, consult your television dealer or local power company. For television sets designed to operate from battery power, refer to the operating instructions.
Page 7
Date:2004-6-24 15:10 ProductView..: Product: Report by....: CT-M809SV Specs / Products +Clock/Timer Functions Clock, On/off timer, Sleep timer Channel +-, Volume +-, +Local Controls Front TV/AV,MENU, Power Switch, +Local Controls Top +Indicators - screen +Indicators - front RC Recvd LED, SB LED +Numb of Loc Cont (incl Mains) +Number of Ind.
Page 8
Date:2004-6-24 15:10 ProductView..: Product: Report by....: CT-M809SV Specs / Products Power Consumption (P)TV in On Less than 10W Power Consumption SB in Watts Power Consumption Semi SB in W +Power in "ON" for +Power in Standby for +Power in "OFF" for Weight (P)TV (incl.
Page 29
Item No. Description Quantity Req. Designator Remarks 67-X38064-0E2 BATTERY SPRING (+/-) 67-X38065-0E2 BATTERY SPRING (+) 67-X38066-0E2 BATTERY SPRING (-) 74-007026-60C POLYBAG (70mmX260mmX0.06mm) 58-HS36Q0-5UI INLAY REMOTE HANDSET 56-399030-0HC REMOTE HANDSET LENS 08-34504E-FC1 02-GND034-XX3 ASS"Y-CRT GND WIRE&HOUSE 25-DFB479-M1X CAP. ELEC 4.7 UF 50V +/-20% BP FOR SP601A &...
Page 30
Item No. Description Quantity Req. Designator Remarks 58-3450FI-0UI INLAY FRONT CONTROL 3409 62-3450SB-00D SPEAKER BRACKET 62-3462PK-0HA POWER KNOB ADAPTE 62-388060-0UA POWER CORD NIP 63-B30060-BT4 S/T SCREW B 3 X 6 BT FOR FUNCTION PCB TO F.CAB 63-B30080-BT4 S/T SCREW B 3 X 8 BT FOR FUNCTION PCB TO F.CAB 63-B40100-BT4 S/T SCREW B 4 X 10...
TCL M113B chassis alignment instruction Enter factory mode in production line Simply press the D-mode key on the factory remote handset. Enter service mode Press and hold the VOLUME DOWN key tightly on the unit until minimum level and don’t release the VOLUMN DOWN key, then press the DISPLAY key on the remote handset.
Page 43
Vertical HITS(11) Input a NTSC Adjust HITS for vertical amplitude. geometry for VP60(02) cross hatch Adjust VP60 for vertical position. NTSC system VLIS(0A) pattern. Adjust VLINS for vertical linearity. (Key 1) VSS(08) Adjust VSS for vertical S-correction VBLK(00) (normally use default value) VCEN(1C) Adjust VCEN for vertical position.
Page 45
Key game OSD1(2B) ---------- (all use default value) (other OSDF1(63) adjustment) OSD2(1C) OSDF2(63) HAFC(09) NOIS(01) UCOM(00) Key 0 R CUT (80) Black and white 1. Measure the dark side of the picture with (White G CUT (80) pattern (PAL) a color analyzer and set RCUT to 80. balance B CUT (80) Then adjust BCUT and GCUT until the...