Table of Contents
Advertisement
Quick Links
CONTENTS
S
!
WARNING
Always keep away from the
slide-out room and rails when
the room is being operated. The
gear assembly may pinch or
catch on loose clothing causing
personal injury
Failure to follow these instruc-
tions could result in serious
injury or death
Introduction
1
SYSTEM DESCRIPTION
1
Your Power Gear Slideout System is a rack and pinion design operated by a 12
2
Volt DC electric motor.
2-3
4
MAJOR COMPONENTS
4
· Inner rail assemblies are designed to support the room weight.
5
· The 12 Volt DC gearmotor will operate the room using power from the on-board
5
unit battery.
6-7
· Slideout systems are equipped with a manual override that allows you to extend
7
/ retract the room in the event of a loss of power.
· A specially designed control that gives the user full control of room movement, in
or out. The control has programmable stops that stop the motor when the room
is fully extended or retracted and the ability to detect faults for ease in
troubleshooting.
Installation
‡ 5HIHU WR µ(OHFWULF 0RWRU 'ULYHQ 6OLGH2XW 2(0 ,QVWDOODWLRQ 0DQXDO 3RZHU *HDU
P/N 81-1291) for proper installation of rail assemblies.
‡ ,I XVLQJ URRP ORFNV UHIHU WR 3RZHU *HDU GUDZLQJ *$ IRU SURSHU
installation of room locks.
‡ Control and touchpad Installation.
0RXQW FRQWURO ER[ )LJ D RU E LQ D ORFDWLRQ WKDW ZLOO SURWHFW WKH FRPSR
nents from the elements and being hit but is easily accessible for service.
'HWHUPLQH ORFDWLRQ WR PRXQW WRXFKSDG )LJXUH /RFDWLRQ QHHGV WR EH
in view of slideout room and have a minimum depth of 1" inside the wall.
Cut 2 7/8" wide x 1 3/4" high rectangular opening in wall to mount the
touchpad.
3. Route and attach touchpad harness to where touchpad will be mounted.
0RXQW WRXFKSDG ZLWK VFUHZV DIWHU V\VWHP KDV EHHQ SURJUDPPHG
4. If using room locks, route and attach room lock harness from control to
room lock.
5. Route and attach the motor and sensor harness from the control box to
the slideout room motors.
6. Route and attach the proper gauge wire from the control to the chassis
battery.
Installation & Service Manual
Room Slideout System with
Control Box 1510000120 and
1510000121
© 1/14 Power Gear #3010001345 Rev. 0C
Installation and
Service Manual
Room Slideout System
with Programmable
Control
Refer to proper wiring diagram in back of manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Power Gear 1510000120
-
Page 1: Table Of Contents
Programmable Control CONTENTS Introduction Introduction SYSTEM DESCRIPTION Installation Your Power Gear Slideout System is a rack and pinion design operated by a 12 Installation Problems Volt DC electric motor. Program Mode Operation Mode MAJOR COMPONENTS Preventative Maintenance · Inner rail assemblies are designed to support the room weight. -
Page 2: Installation Problems
Page 2 Installation Problems CAUTION The control is also equipped to help troubleshoot the system during installation. Count the number of LED flashes and refer to Fault Diagnostics section previous. During Program mode the control has no stop locations If you are still having difficulties programming the system and prior to replacing the and the user must teach the control, verify the system has been wired correctly and the “in”... - Page 3 5HLQVWDOO WKH ZDOO WRXFKSDG 'RQH that the room is clear of people and pets P/N 1510000120 during extension. CAUTION Figure 1a Once the room has reached it’s maximum...
-
Page 4: Operation Mode
Preventative Maintenance causing personal injury. Your Power Gear slide-out system has been designed to require very little maintenance. To ensure the long life of your slide-out system read and follow these WARNING few simple procedures. -
Page 5: Fault Diagnostics
Page 5 Fault Diagnostics The control has the ability to detect several faults. When a fault is detected, the room movement will stop and the RED LED (Figure 7) will flash a number of times corresponding to a specific fault code listed below. 7KHUH DUH W\SHV RI IDXOWV 0LQRU DQG 0DMRU DQG D IDXOW PXVW EH FOHDUHG LQ RUGHU IRU WKH URRP WR RSHUDWH MINOR faults can be cleared by pushing the ‘IN’... -
Page 6: Override Modes
Page 6 Override Modes ,Q WKH HYHQW RI FRPSRQHQW IDLOXUH RI ORVV RI V\VWHP SRZHU CAUTION Your system can be manually overridden NOTE: $W DQ\WLPH GXULQJ WKH RYHUULGH SURFHGXUH WKH XQLW ZLOO H[LW RYHUULGH PRGH LI WKH URRP KDG During override mode the not been moved for 45 seconds or if a fault is detected during overriding, the LED will control has no stop IODVK UDSLGO\ IRU VHFRQGV WR LQGLFDWH WKDW WKH RYHUULGH SURFHGXUH IDLOHG $IWHU ... -
Page 7: Wiring Diagram
Page 7 Wiring Diagram... - Page 8 Page 8 Additional References located at www.lci1.com 3010001346 - Owners Manual Room Slideout System with Control Box 1510000120 and 1510000121 82-SO539 - Encoder Test 1 82-SO540 - Encoder Test 2...
Need help?
Do you have a question about the 1510000120 and is the answer not in the manual?
Questions and answers