Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Artec Mini Tracker 505
- Page 1 Mini Tracker 505 User Manual...
-
Page 2: Care And Maintenance
Care and Maintenance Warning Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet, remove the battery, and allow the device to dry completely before replacing it. Do not use or store the device in dusty, dirty areas. - Page 3 Care and Maintenance The working range, alarm range, searching and detection are depends the terrain environment because of radio wave efficiency. If the beeps sound are not loud enough, it may means the battery low. Change new battery for louder alarm sound.
- Page 4 Overview Master Front Back Distance Left direction indication Buzzer Right direction Mode switch Signal Mute Mute distance indication melody button Power on Search button at search mode (Standby) Power off Hanging hole (Sleeping) for strap Battery cover Clip Slave Front Back Hanging hole for strap Signal indication...
-
Page 5: Working Method
Working Method Master Slave Slave Alarm 8~16 m Alarm Search 100 m Base on open frame condition. Specification Master Slave 39×48×6.8 mm 19×28×7.5 mm Size Frequency 2.4GHz ISM 2.4GHz ISM LR 44 × 2 LR 1 130 × 2 Battery Switch ON / OFF / MUTE 2 buttons... - Page 6 The Battery Installment Master 1. Press the clip on battery cover then push backwardly. 2. Put 2pcs batteries into. *** Make sure the installment direction of positive (+) & negative (-) of battery are followed up the drawing showed on battery cover.
-
Page 7: Getting Started
Getting Started For the first time use, please set the battery into Master according to above battery installment . Pull out Plastic isolation Place two devices no Switch to power on more than 10 cm apart. Beep Caution Distance Beep indication Re-link successful! Signal indication... - Page 8 Search Near 1.) LED light: more closer, more lights. 2.) Search melody: more Press Search button Start to detect the location closer, more rapid. 2~3 seconds of Slave. Wrong holding Correct holding Error indication - whole direction LED goes off but signal LED lights up 3 seconds then displays new searched distance.
- Page 9 Search North Turn to different directions 2 Distance LEDs for signal comparison Go the way of the strongest signal direction to find out One Distance Slave. LED only East 3 Distance LEDs. The strongest signal direction ! West 2 Distance LEDs South...
- Page 10 Search Mute searching melody from Master. Listen beep sound from Slave to assist short range searching. Beep Press & hold the LED Stop the melody Listen to the beep light button sound from Slave...
- Page 11 Search Press Search button 2~3 seconds Stop searching Back to Standby mode Signal indication Signal LED flashes every second for re-linking Error indication - whole direction LED goes off but signal LED lights up 3 seconds then displays new searched distance. 1.) Search from correct direction to wrong direction 2.) Over pass...
- Page 12 Searching Example Location: North North Signal indication East 0 ～ 80 m Go to the wrong direction Distance LED goes out all lights suddenly and only flash Original searching Signal LED with beep sound (Right direction) North East 3 seconds later [Suggestion] LED displays new...
- Page 13 Alarm Beep Beep Signal indication Over 8~16 meter. Stop alarm (beep) if both devices Come with beep! comes within 8 meter again. When Slave and Master are over 100 Caution meter or lose signal Slave flashes half minute to No linking then into sleeping wait for re-linking modeand stop flash...
- Page 14 Sleeping Switch to sleeping mode Switch the button to section 0 (OFF) Under Standby mode Stop signal to Slave Slave flashes half minute to wait for re-linking No linking then into sleeping mode and stop flash...
- Page 15 Re-link / Wake up Beep Beep Distance indication Signal indication Switch the button to Signal LED ON for re-linking Re-link successful! section 1 (ON) Available for distance within Master shows the distance 80 meter between Slave via LED and melody (beep) Beep Can't get signal from Slave.
- Page 16 Mute Mute (Mute At Search mode, Or No Need The Guard Service) Switch to Mute mode Switch the button to section 2 (MUTE) Under Standby mode Press Search button Only Display the distance indication LED without searching melody Under mute mode, the Alarm function is disabled.
-
Page 17: Low Battery
Low Battery 1 beep sound every 120 seconds continuously. If this kit is under low battery stage, it may cause abnormal display to alarm, beeps or non-working to confuse actual working stage. Please change new battery as soon as possible. - Page 18 Suggested setting place Correct Wrong < 90 holding holding Correct Wrong holding holding *** Do not cover the top side of Master.
- Page 19 Suggested setting place Suggested setting place Master Slave...
- Page 20 91E-02B1-U50G11...
Need help?
Do you have a question about the Mini Tracker 505 and is the answer not in the manual?
Questions and answers