Table of Contents
Advertisement
Quick Links
AXS SERIES S40 iCLASS SE
continuous outdoor use in exposed, unsupervised locations. Featuring genuine HID
technology, this access control keypad offers enhanced security by dual factor authentication. Authorized access
through a secured door or barrier can be gained by entry of a valid PIN and/or presentation of an authorized 13.56
MHz contactless card, token or Seos
This manual covers the S40 and S40i, and is available from www.storm-interface.com/downloads. Each individual
product includes a printed datasheet with just the essential information for installation.
Contents
Product Range and Accessories/Options
Supported Credentials
Installation / Wiring Connections
Fitting the Keypad
Wiegand Format / Configuration
Specifications/Regulatory
Whilst every effort is made to ensure details are correct at time of print, specifications are subject to change without notice.
®
®
®
HID
, Seos
and iCLASS SE
are trademarks of HID Global Corporation / ASSA ABLOY AB.
Storm, Storm Interface and Storm AXS are trademarks of Keymat Technology Ltd.
Storm Interface products include technology protected by international patent and design registration.
Storm Interface is an ISO9001 registered company. Storm is a trading name of Keymat Technology Ltd
S40/S40i Engineering Manual
Rev 2.3 May 2016
®
PIN-Contactless Reader: This integrated keypad and contactless reader is rated for
®
device
Page 1 of 8
Engineering Manual for
AXS Series S40/S40i Keypad
®
iCLASS SE
www.storm-interface.com
© Copyright Storm Interface. 2015. All rights reserved
®
®
, Seos
, contactless
Advertisement
Table of Contents
Summary of Contents for iCLASS SE AXS S40
- Page 1 AXS Series S40/S40i Keypad AXS SERIES S40 iCLASS SE ® PIN-Contactless Reader: This integrated keypad and contactless reader is rated for ® ® ® continuous outdoor use in exposed, unsupervised locations. Featuring genuine HID...
-
Page 2: Product Range
A privacy shield (p/n 1KFS020) is available as an optional extra. Supported Credentials The following credentials are supported (additional controller set-up may be required): iCLASS® Seos® 16KB ISO14443A iCLASS SE® SE (32K, 2K) ISO15693 ISO14443B (requires config card) iCLASS® Legacy (16K, 32K. 2K/2 ) ISO15369 iCLASS®... - Page 3 Engineering Manual for AXS Series S40/S40i Keypad Typical Wiring Below is a typical wiring schedule – in this case between the S40 and the Kantech KT-300 Controller The S40 is shown connected to control Door 2. Where there is an LED connection, usually the GREEN LED connection is appropriate Wire name Wire colour...
- Page 4 Engineering Manual for AXS Series S40/S40i Keypad Physical installation - Using the case as a template, mark the position of the four holes (A) on the surface. (or if fixing to an already installed UK or US back box use the relevant hole pattern) - Drill fixing holes to suit the supplied fixing screws - Push the cable through the sealing grommet and secure the case to the mounting surface using the fixing screws - Make the electrical connections to the connector block (the connector block can be removed to aid wiring)
- Page 5 Engineering Manual for AXS Series S40/S40i Keypad Configuration On power-up, you have the option to change the wiegand format, change the site code, or reset to defaults. Power up and press the ‘#’ key within 3 sec and the red led will start flashing, then enter the engineering code ‘#725’. On acceptance, the green LED will be displayed for 2 seconds and the buzzer will sound a confirmation beep.
-
Page 6: Specifications
Engineering Manual for AXS Series S40/S40i Keypad Specifications Card Compatibility iClass ® , Mifare ® serial number ISO15693, ISO14443A&B Card Read Range 2-11 cm (depending on card) Card Security V1 Security (Elite security by special order only) Coupling Frequency 13.56 MHz Power supply... -
Page 7: Change History
Engineering Manual for AXS Series S40/S40i Keypad Change History Engineering Manual Date Version Details Added Change History page 9/5/16 Addition wiegand formats added to flowchart page 5 Product Firmware Date Version Details Added support for additional Weigand formats ( 9/5/16 4/32 &... -
Page 8: Regulatory Information
Engineering Manual for AXS Series S40/S40i Keypad Regulatory Information This device complies with Part 15 of the FCC Rules and Industry Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: 1.