Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Telect T009-5030XXXXXXX
- Page 1 100A Dual-Feed Breaker Panel Model T009-5030XXXXXXX Installation Guide...
- Page 2 1730 N Madson St., Liberty Lake, Washington Telect assumes no liability from the application or use of these products. Neither does Telect convey any license under its patent rights nor the patent rights of others. This document and the products described herein are subject to change without notice.
-
Page 3: Table Of Contents
Figure 7 - Alarm Terminals ......................6 Figure 8 - Designation Label ......................7 Figure 9 - Tab Release ......................... 8 Telect, Inc. • USA +1.509.926.6000 • Mexico +52.33.3836.37.52 www.telect.com • © 2010 Telect, Inc., All Rights Reserved, 139688-1 A0 Page iii... -
Page 4: Overview
WECO: 23 in. (58.4 cm) ETSI: 53.3 cm. Kit sold separately. See “1.5 Accessories” on page 10. Telect, Inc. • USA +1.509.926.6000 • Mexico +52.33.3836.37.52 www.telect.com • © 2010 Telect, Inc., All Rights Reserved, 139688-1 A0 Page 1... - Page 5 @20V: 80mA (1.60W)@24V: 112mA (2.69W) @27V: 120mA (3.24W)@30V: 122mA (3.66W) @40V: 127mA (5.08W)@48V: 130mA (6.24W) @54V: 133mA (7.18W)@60V: 136mA (8.16W) Telect, Inc. • USA +1.509.926.6000 • Mexico +52.33.3836.37.52 www.telect.com • © 2010 Telect, Inc., All Rights Reserved, 139688-1 A0 Page 2...
-
Page 6: Inspection
Immediately report any shipping damage, defects, or missing parts to Telect at 1-800-551-4567. Keep all documentation that comes with your shipment. Telect is not liable for shipping damage. If the product is damaged, notify the carrier and call Telect’s Customer Service Department at 1-800-551-4567 (domestic only) or 1-509-926-6000 for further recourse. -
Page 7: Installation
ALERT! Only use components and crimping tools approved by agencies or certifying bodies recognized in your country or region such as Underwriter’s Laboratories (UL), TUV, etc. Telect, Inc. • USA +1.509.926.6000 • Mexico +52.33.3836.37.52 www.telect.com • © 2010 Telect, Inc., All Rights Reserved, 139688-1 A0 Page 4... -
Page 8: Figure 4 - Ground Lug Connection
8. Make sure power is off (Open the breaker, dummy fuse, or open fuse holder at the power dis- tribution unit [PDU].) before connecting this panel’s cables to the PDU. Telect, Inc. • USA +1.509.926.6000 • Mexico +52.33.3836.37.52 www.telect.com • © 2010 Telect, Inc., All Rights Reserved, 139688-1 A0 Page 5... -
Page 9: Figure 6 - Alarm Indicators
10 AWG.) • If using bare wire, strip off in. (~1.5 cm) of insulation. (Stranded wires should be tinned.) Telect, Inc. • USA +1.509.926.6000 • Mexico +52.33.3836.37.52 www.telect.com • © 2010 Telect, Inc., All Rights Reserved, 139688-1 A0 Page 6... -
Page 10: Figure 8 - Designation Label
19. If covers are installed, remove the covers over the output and alarm connectors. 20. Telect recommends that you lightly coat anti-oxidant on lugs and output BATTERY and RE- TURN terminals before connecting lugs/wires to outputs. (NEC specifies only one lug and load for each output terminal.) Tighten the screws to 9 in.-lb (1.01 N•m). -
Page 11: Replacing Output Circuit Breakers
ALERT! The LINE side connection of the breaker has live Vdc. Do not allow contact of the connector (or tools holding the connector) to grounded ironwork or panel chassis. Telect, Inc. • USA +1.509.926.6000 • Mexico +52.33.3836.37.52 www.telect.com • © 2010 Telect, Inc., All Rights Reserved, 139688-1 A0 Page 8... - Page 12 16. When you turn the new breaker on, check the output terminal for correct polarity. This procedure is complete. Telect, Inc. • USA +1.509.926.6000 • Mexico +52.33.3836.37.52 www.telect.com • © 2010 Telect, Inc., All Rights Reserved, 139688-1 A0 Page 9...
-
Page 13: Accessories
1.5 Accessories The following table lists optional and replacement items for the panel. For compression lugs, please refer to the Wire Sizing & Label Convention Chart (Telect Part No. 117995) included with your panel. Item Description Part Number Alarm Card Power &... -
Page 14: Led & Alarm Summary
C to NO closes. Pressing ALARM RESET turns off the BREAKER ALARM LED and de-energizes the FUSE ALARM relay. Telect, Inc. • USA +1.509.926.6000 • Mexico +52.33.3836.37.52 www.telect.com • © 2010 Telect, Inc., All Rights Reserved, 139688-1 A0 Page 11... -
Page 15: Schematic Drawing
1.7 Schematic Drawing (Not Used) (Not Used) (Shown in alarm state) Telect, Inc. • USA +1.509.926.6000 • Mexico +52.33.3836.37.52 www.telect.com • © 2010 Telect, Inc., All Rights Reserved, 139688-1 A0 Page 12... -
Page 16: Assembly Drawing
2 2.31 [56 .7] 2 3 .00 [58 .4 ] Telect assumes no liability from the application or use of these products. Neither does Telect convey any license under its patent rights or the patent rights of others. This document and the products described herein are subject to change without notice. - Page 17 This page intentionally left blank. Telect, Inc. • USA +1.509.926.6000 • Mexico +52.33.3836.37.52 www.telect.com • © 2010 Telect, Inc., All Rights Reserved, 139688-1 A0 Page 14...
Need help?
Do you have a question about the T009-5030XXXXXXX and is the answer not in the manual?
Questions and answers