Professional installation is required of equipment with connectors to ensure compliance with health and safety issues. Antenna Compliance The LigoPTP 5-23 UNITY radio module contains internal 23dBi antenna. LigoWave Page 3...
CE Mark Warning This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. R&TTE Compliance Statement This equipment complies with all the requirements of the Directive 1999/5/EC of the European Parliament and the Council of 9 March 1999 on Radio Equipment and Telecommunication Terminal Equipment and the Mutual Recognition of their Conformity (R&TTE).
Contact Us ............................6 INSTALLATION ............................7 Package Contents ..........................7 Hardware Introduction ......................... 7 Mounting the LigoPTP 5-23 UNITY ...................... 8 Mounting on a Pole .......................... 8 Mounting on a Wall .......................... 9 ACCESS THE LIGOPTP 5-23 UNITY ....................11 Connection via WEB browser ......................
Purpose The purpose of this guide is to provide a quick and easy explanation of getting started with the LigoPTP 5-23 UNITY. This is only a starter guide and full documentation may be found at our online wiki: http://www.ligowave.com/wiki. Definitions, Acronyms and Abbreviations The following typographic conventions and symbols are used throughout this document: Additional information that may be helpful but which is not required.
If any of these items are missing or damaged, please contact your reseller. Hardware Introduction The LigoPTP 5-23 UNITY unit is housed in rugged, cast aluminum enclosure and has an integrated 23dBi directional antenna. Figure 1 – LigoPTP 5-23 UNITY Overview The label of the LigoPTP 5-23 UNITY contains following information: ...
Installation Mounting the LigoPTP 5-23 UNITY Mounting bracket of LigoPTP 5-23 UNITY is designed to make installation on a wall or a pipe easy. The unit is attached and its position is fixed with the single bolt. Mounting on a Pole The PTP units are supplied with mounting hardware for pole with diameters in the range 10mm to 70mm installations.
The mounting bolts for unit installation on the wall are not included in the package. For mounting LigoPTP 5-23 UNITY unit on the wall, first mount one half of the bracket to the wall and then connect the two halves of the bracket together and tighten the nut and bolt.
Page 10
It is recommended not to tighten the units to its mounting brackets until the alignment process of the antenna is complete. Step 7. Power-up the LigoPTP 5-23 UNITY unit. It is recommended to use shielded Ethernet cable to reduce exposure of the electromagnetic noise.
Access the LigoPTP 5-23 UNITY Access the LigoPTP 5-23 UNITY The first connection to the LigoPTP 5-23 UNITY can be made using a standard Ethernet cable connected directly to your PC. See next sections for the instructions on how to access the LigoPTP 5- 23 UNITY management interfaces.
Resetting to Factory Defaults LigoPTP 5-23 UNITY units have the capability of being reset to defaults by pinging the device with a certain packet size when the radio is booting. During the startup of the device, when the drivers of the ethernet interfaces are loaded, the discovery daemon is started.
Quick Installation Guide Access the LigoPTP 5-23 UNITY OLED Display Control LigoPTP 5-23 UNITY products have the capability to monitor the primary device’s parameters and execute maintenance tasks through an OLED display and keypad. OLED display menu: Unlock/Lock ...
Alulírott, Deliberant nyilatkozom, hogy a Ligowave LigoPTP 5-23 UNITY, megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Íslenska [Icelandic] Hér með lýsir Deliberant yfr því að Ligowave LigoPTP 5-23 UNITY, er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC. Italiano [Italian] Con la presente Deliberant dichiara che questo Ligowave LigoPTP 5-23 UNITY, è...