Page 2
(4) To improve the product performance, functions can be changed with no notice. (5) Please understand that CAS does not have responsibility for a demand related to loss, lost profit etc. caused by operating the product, regardless of the third clause.
Do not connect incompatible adaptor. Use only adaptor approved by CAS for use with this particular model. The use of any other types may invalidate any approval or warranty, and may be dangerous. For availability of approved enhancements, please check with your dealer.
4. Description of Panels and Symbols DISPLAY Displays weight or messages Indicates that the weight to be in stable condition ZERO lamp Indicates that scale is stable and at zero Kg/lb lamp Unit conversion operating lamp Indicates that scale is currently using a tare TARE lamp Power lamp Power lamp...
5. Installation Power adaptor + (RED) Power adaptor – (BLACK) Not used (Extra RS232C TXD) Not used (Extra RS232C RXD) Not used (Extra RS232C GND)
Page 8
Not used RS232C TXD (OP-01) RS232C RXD (OP-01) RS232C GND (OP-01) Not used SIG+ SIG- POWER ZERO External key 4 contact / 4inputs (OP-01) TARE “HOLD” mark is the same as “kg/lb” HOLD EVCC+ OUT1 2 solid state relays contact (OP-01) EVCC+ OUT2...
Page 9
1) External input circuit External inputs are interlocked with the touch keys. 2) Solid state relay circuit Maximum load (AC, DC 350V /130mA) Output conditions Output Conditions OUT2 ON (low limit) Low limit< Measured value ≤ High limit OUT1 ON (high limit) High limit <...
6. General Function 6.1. Zero function Use to correct drifted zero value when the scale is unloaded, and motion is not detected. This function works when ZERO KEY is pressed, and the ZERO LAMP is on. 6.2. Setting Tare Weight Function Press the TARE KEY.
7. Test Mode (1) How to enter this mode Press the ON KEY to power on and immediately press ZERO KEY to enter test mode. (2) Testing Menu (TEST 1- TEST 2) ■ TEST 1 : Keyboard Test Remote Display Description Control Press a keyboard that you want to test, and...
8. Setting Mode 8.1. How to enter this mode Press the ON KEY to power on and immediately press TARE KEY. And press the TARE KEY again. 8.2. Keyboard ■ : Use to set up an initial zero value (0). (F12, F13: Used to move the input value to the left or right by one place) ■...
Page 13
■ F04: Print line feed (0~9) Setting Menu Description F04-0 1 line feed F04-5 6 line feed F04-9 10 line feed ■ F05: Print form (0,1) Setting Menu Description F05-0 Form 0 (weigh No., Item No., weight) F05-1 Form 1 (Serial No., Item No., weight) When the F02-1 is selected, this form is printed.
Page 14
■ F09: Wireless connection of other company’s product (0~2) Setting Menu Description F09-0 Not used F09-1 Product with 22bytes RS232C format F09-2 Product with 18bytes RS232C format If you select F09-1 or F09-2, you must use the CRC-200 dongle at the scale. ■...
9. Infrared Remote Controller 9.1. How to use ■ : Use to power on/off the CRD-F series ■ Same as keyboard of CRD-F series ■ Same as keyboard of CRD-F series ■ Same as keyboard of CRD-F series ■ Same as keyboard of CCB crane scale ■...
11. RS-232C Interface 1) Type : EIA-RS-232C 2) Method : Full-duplex, asynchronous transmission Format ① Baud rate: 9600 bps ② Data bit: 8 bits ③ Code : ASCII 3) Format (22bytes) Header 1 Header 2 Data Unit Terminator , G S , Lamp status Stable weight data (0x53) (0x54) Unstable weight data (0x55) (0x53)
12. Real Time Clock 1) How to enter this mode Press the ON KEY to power on and immediately press kg/lb KEY. And press the TARE KEY. 2) Keyboard Used to increase the setting constant one by one. Used to move the input value to the left or right by one place. Used to save the value and to move next menu.
13. Wireless Pairing Step Operation & Description How to enter the pairing mode 1) CCB crane scale When the display is off, press ON/OFF key while pressing * key. When “ = ”(Firmware version) is displayed, press kg/lb key. Then, “ ”...
14. Check Message When a thing is over-weighed within the maximum weight value, the error message is displayed. Do not weigh the thing whose the limit of a maximum weight value is exceeded. If a load cell is broken, then the load cell has to be replaced. Something wrong in a Load cell connection or in an A/D conversion.