Related Manuals for PARK AUDIO DX1000T DSP
Summary of Contents for PARK AUDIO DX1000T DSP
- Page 1 PARK AUDIO PROFESSIONAL BUILT-IN THREE-CHANNEL POWER AMPLIFIERS WITH DSP OWNER’S MANUAL...
- Page 2 AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION! The amplifier runs on 230 V AC voltage. Removing the cover will expose you to a potentially dangerous voltage! Do not use the unit if the electrical power cord is frayed or broken.
- Page 3 INTRODUCTION The DX1000T , DX1400T , DX2100T three-channel amplifiers are designed for installation inside subwoofer which is a part of the active set – subwoofer plus 2 satellites. One amplifier channel is used to connect the subwoofer, the other two – for satellites. To create the necessary signal processing path, including crossovers, EQ and dynamic processing, the DSP engine is used in the amplifier.
- Page 4 DESIGN AND FUNCTIONAL FEATURES Design The built-in power amplifier is designed as a mono-block unit. All its components are installed on a single bearing panel placed inside the case which protects the unit and ensures its deep placement into the body of a speaker system. Power to the built-in power amplifier is supplied via a removable power cord.
-
Page 5: Power Led
The DSP preset switch enables choosing various settings for the subwoofer and satellite channel, created by the DSP sound proceeding. USB interface enables changing the parameters and presets overwriting. Overload and Short-Circuit Protection This protective system becomes active in case of short-circuited output or overload caused by reduced load impedance. - Page 6 Limiter’s User Manual – recommendations on limiters setting in signal processing tracts (Limiter_UM_en.pdf); Project Templates – SigmaStudio project template for amplifiers with DSP (Project_DX_T_dsp.zip ); Factory DSP Presets – DSP preset settings description (DSP setting _DX_T_dsp.xls). Limiter’s Setting Calculations – simple calculator (Excel) to calculate the parame- ters of the limiter (Limiters_calculation.xls).
-
Page 8: Controls And Connectors
CONTROLS AND CONNECTORS... - Page 9 POWER – power switch. TO SATELLITE LEFT – left satellite channel output. MAINS IN – power cable socket. ATTENTION! The mains parameters are indicated below the power cord socket: – for the amplifiers without PFC: ~230V AC 50/60Hz; – for the amplifiers with PFC: ~160-250V AC 50/60Hz. ATTENTION! The power to the amplifier is supplied from single-phase AC power mains 230 V and ~50/60Hz with protective grounding.
-
Page 10: Cable Requirements
CABLE REQUIREMENTS Input Cables Make sure to use only shielded cables whether balanced or unbalanced. As a rule, unbalanced lines of over 3 meters long are not acceptable. Shielding, when properly grounded, protects a signal against external radio interference, interference generated by dimmers and other electric noise. - Page 11 CONNECTORS Input Connectors Use XLR (male) connectors to connect to the line inputs and XLR (female) connectors to the line outputs. See the connectors wiring below. XLR (male) XLR (female) Cold (–) Cold (–) Hot (+) Shield (Ground) Hot (+) Shield (Ground) Output connectors Use SpeakON NL2FC or NL4FC connector to connect the loudspeaker-satellite to the...
-
Page 12: Ac Power Requirements
Insert the amplifier into a cutout in the rear panel of a loudspeaker. For installation of the amplifier we recommend a cutout of the following size: – for amplifiers DX1000T DSP, DX1400T DSP: width 158mm, height 369mm; – for amplifier DX2100T DSP: width 158mm, height 435mm. -
Page 13: Specification
SPECIFICATION Output Power *: – DX1000T 350 W (subwoofer channel, 8 Ohms) 2 х 350 W (satellite channels, 8 Ohms) – DX1400T 700/380W (subwoofer channel, 4 / 8 Ohms) 2 х 350 W (satellite channels, 8 Ohms) – DX2100T- 4 1400 / 800W (subwoofer channel, 4 / 8 Ohms) 2 х... - Page 14 DIMENSIONS DX1000T , DX1400T 14 max 156 max...
- Page 15 DIMENSIONS DX2100T 14 max 157 max...
- Page 16 PARK AUDIO II, Ltd. Ukraine, Vinnytsia parkaudio.ua e-mail: park@parkaudio.ua...