Table of Contents
Advertisement
FCC Part 15 C Notice
CAUTION:Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against
harmful interference in a residential installation.This equipment generates,uses and can radiate radio
frequency energy and,if not installed and used in accordance with the instructions,may cause harmful
interference to radio communications.However,there is no guarantee that interference will not occur in a
particular installation.If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions :
(1) This device may not cause harmful interference,and
(2) this device must accept any interference received,including interference that may cause undesired
operation.
INDUSTRY CANADA NOTICE: CANADA ONLY.
This device complies with Industry Canada licence-exempt RSS standard(s).Operation is subject to the following two conditions:
(1) this device may not cause interference,and (2) this device must accept any interference,including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.L'exploitation est
autorisée aux deux conditions suivantes :(1) l'appareil ne doit pas produire de brouillage,et (2) l'utilisateur de l'appareil doit
accepter dout brouillage radioélectrique subi,même si le brouillage est susceptible d'en compromettre le fonctionnement.
WARNING!
CHOKING HAZARD - Small parts.
Not suitable for children under 3 years.
Conforms to safety requirements of FCC.
©2016 Rooftop Brands™ All rights reserved
Tel:+ (1) 949-566-9573 • www.propelrc.com
ORBIT
2.4GHz Quadrocopter With HD Camera
WARNING: Never leave product charging unattended for extended periods of
time. Always disconnect ORBIT
is fully charged. Please refer to enclosed safety instructions.
TM
ORBIT HD
2.4G Wireless Controller
Made in China
HD
TM
INSTRUCTION BOOKLET
HD battery from charger immediately after it
TM
PACKAGE CONTAINS:
Spare Parts
USB Charger
USB Card Reader
Memory card
& Li-Poly
Rechargeable Battery x 3pcs
Colors and styles may slightly vary.
Instruction Manual
Advertisement
Table of Contents
Related Manuals for Propel RC ORBIT HD
Summary of Contents for Propel RC ORBIT HD
- Page 1 Not suitable for children under 3 years. Spare Parts USB Charger USB Card Reader Memory card Instruction Manual ORBIT HD 2.4G Wireless Controller Conforms to safety requirements of FCC. & Li-Poly Rechargeable Battery x 3pcs ©2016 Rooftop Brands™ All rights reserved Tel:+ (1) 949-566-9573 •...
-
Page 2: Table Of Contents
TABLE OF CONTENTS FEATURES • 6 Axis Gyro For Extremely Stable Flight and Maneuverability Product Features ............2 •... -
Page 3: Orbit™ Hd Quadrocopter Diagram
2. Insert the battery into the compartment in the right direction and set it down on a flat surface.The LED indicator lights of the ORBIT™ HD should begin to flash (see diagram D). Antenna 3. Next turn ON the remote controller.After hearing a series of beeps,the ORBIT HD's flashing LED Power Indicator lights will start flashing at a slower rate.Pull the throttle (left control stick) all the way up and then all... -
Page 4: How To Start/Stop Rotors
HOW TO START/STOP ROTORS Move the left Throttle stick left and the ORBIT™ HD will rotate left. Make sure you have properly synced the ORBIT™ HD and the power stay on. • To start the rotors simply move the two control sticks both down and all the way in the corners,hold until the rotors Move the left Throttle stick right and the starts spinning.Now release both sticks to the neutrall position and push the throttle up to take off. -
Page 5: Level Surface Calibration
LEVEL SURFACE CALIBRATION If the aircraft becomes unstable during the course of flying, you may need to restabilize the internal gyros. To do this,Turn Off the controller and disconnect the Drone battery.Place the ORBIT™ HD on a flat level surface.Follow the steps to sync your ORBIT ™... -
Page 6: Replacing The Propeller Blades
ORBIT™ HD WARNING: OPERATING THE CAMERA The ORBIT™ HD is designed for OUTDOOR use only. The ORBIT™ HD blades revolve at high speeds and can You can take in-flight photos or video with your ORBIT™ HD on board camera. cause damage to the user,spectators and animals.Stand away from the ORBIT™ HD to reduce the risk of 1.
Need help?
Do you have a question about the ORBIT HD and is the answer not in the manual?
Questions and answers
lights blinkin o remote controller