1. Product introduction 1.1. Outline VMAX-MIPI is a pattern generator which supports Full-HD resolution. VMAX-MIPI has one MIPI connector (29pin), 4 programmable power outputs.All power channels are measured in real time. Bundle software which provided is proper with Windows XP or Windows 8. That software called“VMAX_Terminal”.
Max 4000 images (based on 128 X 128) Max 840 images (based on 240 X 320) Current Channel 4 x 1 block measuring * Note : VMAX-MIPI-P2BL model support in Back Light power(20mA). (LED+,LED-) ** Note : Only VMAX-MIPI-P3FBL model support. VMAX-MIPI User’s Manual Ver 1.20...
1.4.1. Power Jack, USB Jack, MIPI-FHD Port side Reset button, MIPI-FHD connector, USB connector, DC power input and Power ON/OFF switch are placed at front panel. There are four buttons: ON / OFF / Image up / Image Down VMAX-MIPI User’s Manual Ver 1.20...
BARUN Technology Corporation http://www.baruntechnik.com 1.4.2. Top side There are two line character LCD and 5 color LED. VMAX’s status displayed at line character. VMAX-MIPI User’s Manual Ver 1.20...
Monitor Current sensing activate when module turn on. Stored for real-time command and VMAX response message. Video file download and delete. VMAX in four buttons, and the DEMO button. Operation status is displayed as a message. VMAX-MIPI User’s Manual Ver 1.20...
BARUN Technology Corporation http://www.baruntechnik.com 2.1. Installation VMAX installation is very easy. Just click VMAX_Term_Setup.exe in CD-ROM. When user click VMAX_Terminal_Setup.exe ,setup program make directory “C:\VMAX\VMAX_MIPI” and every data copied under the directory.. VMAX-MIPI User’s Manual Ver 1.20...
Model catalog / Download / Delete Model of this window within the VMAX DownLoad button a list of the desired model is available for download. Want to DELETE button to delete the list of models. Video file transfer and delete VMAX-MIPI User’s Manual Ver 1.20...
Page 16
Five remote USB port using virtual key pads. This button is the same function with the keys on the side of the VMAX DEMO button that runs in the ME-ON state should run the command key DEMO.txt VMAX-MIPI User’s Manual Ver 1.20...
Page 17
Data Latch Timing: rising edge or falling edge to latch data. ○ Frame Rate: How many frame image display per second ○ Set HWS, BP(Back Porch),FP(Front Porch)and Level of Hsync. ○ SetVWS, BP(Back Porch),FP(Front Porch)and Level of Vsync. VMAX-MIPI User’s Manual Ver 1.20...
Page 18
*VMAX products, depending on the model, you can receive each of the 2-channel / 4-channel / 6-channel. Range of voltages and currents set also can vary depending on the model VMAX product. Therefore specifications required. I/O Buffer Power part of the MIPI-GIPIO pin to set the output voltage. VMAX-MIPI User’s Manual Ver 1.20...
Page 19
Each of the five Key Remote key corresponding to the command file. In other words, ON Key file is executed by pressing the ON key file is executed by pressing the OFF key. Image Over-View VMAX-MIPI User’s Manual Ver 1.20...
Page 20
There are several function keys to help easy editing. “Select Image” window appeared when you click “Add”. If you already saved test patterns under test model directory, you can see whole patterns. And just select what you want and select “Open”. VMAX-MIPI User’s Manual Ver 1.20...
Page 21
Download and Delete User can download model data to SD card of VMAX-MIPI.15 model data could be store to SD card. Select number from 1 to 15 and click “DownLoad”. Now a window popped titled “Select MIPI-FHD Mode”. User select can select model and type.
Page 22
BARUN Technology Corporation http://www.baruntechnik.com Select main module data and click “Model” button Select data type among ALL DATA, Image, Information/Instruction Chose main model data what you want to download OK: Start download. Cancel: Exit without download. VMAX-MIPI User’s Manual Ver 1.20...
Exit the MIPI video mode. mipi.hs.enable Enable MIPI HS mode. mipi.hs.disable Disable MIPI HS mode. pwrport.on Set module power on the VMAX-MIPI pwrport.off Set module power off the VMAX-MIPI pwrbase.on Set Bridge board control signal buffer power ON. pwrbase.off Set Bridge board control signal buffer power OFF.
Page 24
Display next image image.prev Display previous image image.repeat Display image repeatedly board.power.on led Set module Back-light on(VMAX-MIPI-P2BL only) board.power.off led Set module Back-light off(VMAX-MIPI-P2BL only) mipi.lane.enable Lane Enable : Hi-Z -> STOP state(LP11) spi.bridge.write Bridge chip Register write command spi.bridge.read...
Page 25
BARUN Technology Corporation http://www.baruntechnik.com power.off all Set module power off all the VMAX-MIPI gpio.link.level VMAX Terminal, I/O Buffer power voltage level mipi.timing.lp LP Clock Timing control command mipi.timing.data HS Data Timing control command mipi.timing.clk HS Clk Timing control command mipi.read.show Read MIPI module register data display.
Page 26
Up Key script run command KeyDown.run Down Key script run command KeyF1.run F1 Key script run command KeyF2.run F2 Key script run command KeyF3.run F3 Key script run command KeyF4.run F4 Key script run command VMAX-MIPI User’s Manual Ver 1.20...
Page 27
Receive Data : None address command spi.bridge.read data1 data2 Description : Read SPI data from the bridge board. Parameters : a count of data that read from the bridge board. Receive Data : received SPI data VMAX-MIPI User’s Manual Ver 1.20...
Page 28
Parameters : None Receive Data : None mipi.video.disable Description : Exit the video mode. Parameters : None Receive Data : None mipi.clock.enable Description : Enable mipi high speed clock. Parameters : None. Receive Data : None VMAX-MIPI User’s Manual Ver 1.20...
Page 29
1 to ON , 0 to OFF Receive Data : None mipi.gpio1 para Description : Set Module connector pin 18 level control. parameters : 1 para 1 to ON , 0 to OFF Receive Data : None VMAX-MIPI User’s Manual Ver 1.20...
Page 30
1 to ON , 0 to OFF Receive Data : None power1 power2 … pwrport.on Description : Turn on the module powers on the application board. parameters : a power in parameter list is turn on Receive Data : None VMAX-MIPI User’s Manual Ver 1.20...
Page 31
Description : Wait for the amount of time, in milliseconds. parameters : the amount of time, in milliseconds Receive Data : None repeat_number loop Description : Repeat command from loop to loopend n times. parameters : repeat number Receive Data : None VMAX-MIPI User’s Manual Ver 1.20...
Page 32
YELLOW(5), CYAN(6), MAGENTA(7) Transparent option, ( 0 = Disable, 1= Enable) Image Name Font 0 = Font 8x15 1 = Font Arial12 2 = Font 16x16 Bold 3 = Font ArialBold22 Image Name display position VMAX-MIPI User’s Manual Ver 1.20...
Page 33
2 for generic packet parameter 1 for DCS packet Receive Data : None para1 para2 para3 var1.init Description : Variable-data-field initilize parameters : 3 para 1 initilize data para 2 upeer limit para 3 lower limit Receive Data : None VMAX-MIPI User’s Manual Ver 1.20...
Page 34
Background color = BLACK Transparent = Enable Font size = 8x15 Dot parameters : None Receive Data : None var1.print.off Description : Variable data packets display disable command parameters : None Receive Data : None VMAX-MIPI User’s Manual Ver 1.20...
Page 35
Transparent option, ( 0 = Disable, 1= Enable) Image Name Font 0 = Font 8x15 1 = Font Arial12 2 = Font 16x16 Bold 3 = Font ArialBold22 var1 display position Receive Data : None VMAX-MIPI User’s Manual Ver 1.20...
Page 36
Bit[6:4] Range 0~7, LVDS input skew control for channel D. Bit[2:0] Range 0~7, LVDS input skew control for channel E. Para5 LVTTL output time control, reg.1ch Para6 LVTTL output setup and hold time control, reg.1dh Para7 LVTTL output enable/disable control. reg.1eh VMAX-MIPI User’s Manual Ver 1.20...
Page 37
Receive Data : None para1 para2 para3 para4 dm600.dsic Description : Send dm600 sub-card skew register control packet Parameters : any bytes of SPI data. parameter value Para1 LVTTL input delay control,reg.1ah Para2 Vod adjustments,reg.1ch VMAX-MIPI User’s Manual Ver 1.20...
Page 38
BARUN Technology Corporation http://www.baruntechnik.com Para3 LVDS O/Ps available after TCLK cycle. reg.1fh Para4 LVDS Output Enable/Disable reg.1eh Receive Data : None VMAX-MIPI User’s Manual Ver 1.20...
Page 39
Description : Module power all off command. parameters : None Receive Data : None GPIO Buff power voltage level gpio.link.level Description : GPIO Buffer power voltage level parameters : 1 Receive Data : None VMAX-MIPI User’s Manual Ver 1.20...
Page 40
TA-GO Timing TA-GET Timing TA-SURE Timing [P1] [P2] {P3} [P4] mipi.timing.data Description : mipi HS data Timing for delay parameters : 4 parameter value HS-PREPARE HS-ZERO HS_TRAIL HS-EXIT VMAX-MIPI User’s Manual Ver 1.20...
Page 41
Display Bytes Data Identifier (Read command, 0x06,0x04,0x14) Para1 parameter 1 for module DCS command (Read Address) Para2 parameter 2 for return size Para3 Nickname, (ex. {DEV ID}) Receive Data : any bytes of mipi packet data. VMAX-MIPI User’s Manual Ver 1.20...
Page 42
1 = Font Arial12 2 = Font 16x16 Bold 3 = Font ArialBold22 mipi.read display position Receive Data : None mipi.read.show.off Description : mipi read data packets display disable command parameters : None Receive Data : None VMAX-MIPI User’s Manual Ver 1.20...
Page 43
Receive Data : None Buffer-Number ~ Buffer-Number SetcionFALSE EndOfSetcionFALSE Description : mipi.read.iif subfunction, compare result true. parameters : 1 Receive Data : None delay-time(ms) beep Description : Buzzer beep sound command. parameters : 1 Receive Data : None VMAX-MIPI User’s Manual Ver 1.20...
Page 44
R0~255, G0~255, B0~255 image. Description : Fill pattern generation command. parameters : 3 Receive Data : None Port Number dvm.measure.set. Description : Power Port 1/2 voltage output offset command parameters : 1 Receive Data : None VMAX-MIPI User’s Manual Ver 1.20...
Page 45
Description : Exiting from the ULPS parameters : None Receive Data : None KeyOn.run Description : Key On script running command. parameters : None Receive Data : None * This command is turned on when the executable. VMAX-MIPI User’s Manual Ver 1.20...
Page 46
Receive Data : None * This command is turned on when the executable. KeyF3.run Description : Key F3 script running command. parameters : None Receive Data : None * This command is turned on when the executable. VMAX-MIPI User’s Manual Ver 1.20...
Page 47
BARUN Technology Corporation http://www.baruntechnik.com KeyF4.run Description : Key F4 script running command. parameters : None Receive Data : None * This command is turned on when the executable. VMAX-MIPI User’s Manual Ver 1.20...
MIPI Bridge device read function, first byte the register address, second byte must be 0xFA 3.1.6. MIPI-FHD Image types 24 bit [888] Transfer image data by 24 bit (888). 18 bit [666] Transfer image data by 18 bit (666) one times. Connected to CELLdata bit 0 ~ 17 VMAX-MIPI User’s Manual Ver 1.20...
Page 53
BARUN Technology Corporation http://www.baruntechnik.com 16 bit [565] Transfer image data 16 bit (565) one times. Connected to CELL data bit 0 ~15. VMAX-MIPI User’s Manual Ver 1.20...
Example Error code ) Error code that is displayed in the file # and // lines that begin with will not be displayed. This error code beginning with a capital letter W. ( modify it to wait ) VMAX-MIPI User’s Manual Ver 1.20...
Page 55
However, the following cases are allowed. ex) #board.power.on led;// 5. Tags ';' Be careful not followed by space. Tag this case "a" is interpreted as. ex) wait 100;[space] [Enter] -> wait 10; Error ; <- occurs error VMAX-MIPI User’s Manual Ver 1.20...
Page 56
1 2; vio -> 2 board.power.off pwrport.off vdd -> 1 vio -> 2 gpio.link.level I/O Buffer Power update power.off all pwrall.off delay wait gpio.dir pwrbase.on; Bit Mask stored gpio.write [HEX] mipi.gpio[BitMask] [Bit] VMAX-MIPI User’s Manual Ver 1.20...
// 5sec EndOfSectionFALSE 0; Result) If { ID Code OK } when routine execute to SectionTRUE ~ EndofSectionTRUE , else to SectionFALSE ~ EndOfSectionFALSE. 3.1.10. MIPI Read (mipi.read.iif) Example Instruction "mipi.read.iif" , *Only support scripts (ON/OFF/UP/DOWN/DEMO/F1/F2/F3/F4) VMAX-MIPI User’s Manual Ver 1.20...
Page 60
2 0 0x06 0xE2 5 {GAMMA =} {0x00 0x00 0x00 0x00 0x00 0x00}; mipi.read.iif 3 0 0x06 0xE2 5; #================================================== DEVICE ID = ID Code NG DEVICE ID = ID Code OK GAMMA = 00 00 00 00 00 00 00 00 00 00 VMAX-MIPI User’s Manual Ver 1.20...
BARUN Technology Corporation http://www.baruntechnik.com 5.2. Typical Patterns The generated test image data are show in the table below. <Table Image pattern > Test Pattern Remark Raster WHITE Raster RED Raster GREEN Raster BLUE VMAX-MIPI User’s Manual Ver 1.20...
Page 67
BARUN Technology Corporation http://www.baruntechnik.com Test Pattern Remark Raster WHITE(31) Raster WHITE(60) Raster WHITE (127) Gray Pattern RED(127) Gray Pattern GREEN(127) Gray Pattern BLUE(127) VMAX-MIPI User’s Manual Ver 1.20...
Page 68
BARUN Technology Corporation http://www.baruntechnik.com Test Pattern Remark ColorBar-H4 ColorBar-V4 ColorBar-H8 ColorBar-V8 Blue H+ Grayscale Green H+ Grayscale Test Pattern Remark VMAX-MIPI User’s Manual Ver 1.20...
Page 69
BARUN Technology Corporation http://www.baruntechnik.com CYAN H+ Grayscale RED H+ Grayscale MAGENTA H+ Grayscale YELLOW H+ Grayscale WHITE H+ Grayscale H4+ Grayscale VMAX-MIPI User’s Manual Ver 1.20...
Page 70
BARUN Technology Corporation http://www.baruntechnik.com Test Pattern Remark V4H+ Grayscale H8H+ Grayscale V8H+ Grayscale BLUE H- Grayscale GREEN H- Grayscale CYAN H- Grayscale VMAX-MIPI User’s Manual Ver 1.20...
Page 71
BARUN Technology Corporation http://www.baruntechnik.com Test Pattern Remark RED H- Grayscale MAGENTA H- Grayscale YELLOW H- Grayscale WHITE H- Grayscale H4H- Grayscale V4H- Grayscale VMAX-MIPI User’s Manual Ver 1.20...
Page 72
BARUN Technology Corporation http://www.baruntechnik.com Test Pattern Remark H8H- Grayscale V8H- Grayscale BLUE V+ Grayscale GREEN V+ Grayscale CYAN V+ Grayscale RED V+ Grayscale VMAX-MIPI User’s Manual Ver 1.20...
Page 73
BARUN Technology Corporation http://www.baruntechnik.com Test Pattern Remark MAGENTA V+ Grayscale YELLOW V+ Grayscale WHITE V+ Grayscale H4V+ Grayscale V4V+ Grayscale H8V+ Grayscale VMAX-MIPI User’s Manual Ver 1.20...
Page 74
BARUN Technology Corporation http://www.baruntechnik.com Test Pattern Remark V8V+ Grayscale BLUE V- Grayscale GREEN V- Grayscale CYAN V- Grayscale RED V- Grayscale MAGENTA V- Grayscale VMAX-MIPI User’s Manual Ver 1.20...
Page 75
BARUN Technology Corporation http://www.baruntechnik.com Test Pattern Remark YELLOW V- Grayscale WHITE V- Grayscale H4V- Grayscale V4V- Grayscale H8V- Grayscale V8V- Grayscale VMAX-MIPI User’s Manual Ver 1.20...
Page 78
BARUN Technology Corporation http://www.baruntechnik.com Test Pattern Remark BLACK GREEN BLUE W GRAY H+ W GRAY H- VMAX-MIPI User’s Manual Ver 1.20...
Page 79
BARUN Technology Corporation http://www.baruntechnik.com Test Pattern Remark W GRAY V+ W GRAY V- RGB H256 SLANT RED SLANT GREEN SLANT BLUE VMAX-MIPI User’s Manual Ver 1.20...
Page 80
BARUN Technology Corporation http://www.baruntechnik.com Test Pattern Remark 1 Dot Reverse PT Gray32_C/T VMAX-MIPI User’s Manual Ver 1.20...
BARUN Technology Corporation http://www.baruntechnik.com 5.4.2. UPLS Support The VMAX-MIPI has ULPS support to commands of mipi.sleep.enable and mipi.sleep.disable. < Figure. VMAX-MIPI Low Power Data Transmission Command wave > < Figure. VMAX-MIPI ULPS Pattern from “mipi.sleep.enable” > Exit ULPS to LP11 states of “mipi.sleep.disable” command.