Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for TTI Buddy BX5
Summary of Contents for TTI Buddy BX5
- Page 1 Buddy BX5 5CH Million Pixels HD Multi-functional Mobile DVR USER MANUAL Ver 1.8...
- Page 2 Tips about safety instruction & direction Before installing and using please read the following warning carefully. The recorder uses DC power supply, input DC range is 8V-36V, Please pay attention to VDD and GND when connecting the power, DO NOT make DVR short-circuit.
- Page 3 Introduction The manual is about the features and specifications of one kind of car DVR, it is an integration of “5 monitoring and recording ”, ”Million Pixels Digital&Analog mixed car DVR”, “wireless data transmission ”. In the manual it describes the functions and considerations of the modules ,the connector signal definitions in the back panel, the interface definition and user’s operations.More details,please check following directory.
-
Page 4: Table Of Contents
Contents 1. System Introduction............................- 5 - 1.1. Product features............................- 5 - 1.2. Appearance...............................- 7 - 1.3 Remote Controller........................... - 8 - 1.4 Fron tand Back Panel..........................- 9 - 1.4.1 Fron LED Indicators........................- 9 - 1.4.2. Back Panel IO Indicators......................- 10 - 1.5 Product Introduction.......................... - Page 5 5.6.5 IPC Setup............................- 29 - 5.6.6 FTP Setup............................. - 30 - 5.7 Alarm Setup.............................- 30 - 5.7.1 IO Alarm............................- 30 - 5.7.2 Speed Alarm..........................- 32 - 5.7.3 Temperature Alarm........................- 32 - 5.7.4 G-sensor............................- 33 - 5.7.5 Voltage Alarm..........................- 33 - 5.7.6 Motion Detection........................
-
Page 6: System Introduction
System Introduction 1.1. Product features H.264 Compression Mode, Max support 5CH Million pixels HD video surveillance/ recording/ playback (4CH real-time 720P Million Pixels AHD input or 4CH Analog Standard Definition camera input, or 2CH HD input+2CH SD input) + 1CH 1080P IP Camera input ;... - Page 7 Display vehicle traffic status, Vehicle numbers ,Route, Super-low speed vehicle Information, Convenient management. Support GPS/BD,Gsensor Modules Extension. 3channels RS232 +2channel RS485. Superior network function, can configure menu through IE, support mobile SMS to configure parameters and obtain device infomation. Support Video&Audio monitoring,2-way Intercom, PTZ control, manually Alarm,Overspeed,Geo Fence ...
-
Page 8: Appearance
1.2. Appearance Product appearance pictures are displayed as follows: - 7 -... -
Page 9: Remote Controller
1.3 Remote Controller Function Picture Power and Standby Button,Reserved To enter system settings. [0－9] key:In the setting mode, 0-9 is used to select the number of menu items. In playback mode, the key 1,2,3,4 to select single channel playback, ESC Button for 4-channel playback. Delete Button Return to the preview picture or previous menu Enter button: button for setting system parameter,... -
Page 10: Fron Tand Back Panel
1.4 Fron tand Back Panel 1.4.1 Fron LED Indicators 1—HDD Lock, it’s used for unload hard disk. （Device will power off automatically if power on when HDD lock is open） 2—HDD Fixed Screw . Please manually tighten screw after installing hard disk drive, to prevent HDD slip out ; 3—... -
Page 11: Back Panel Io Indicators
1.4.2. Back Panel IO Indicators 1— Video&Audio Input interface, 1-4Channels or 1-8Channels, with DC 12V output: 2—16 PIN Extension Port , With Video&Audio output interface、alarm input&output、serial port etc. 3—24 PIN Extension Port , With alarm input&output、serial port etc.More detailed definition see addenda. -
Page 12: Product Introduction
1.5 Product Introduction Before use,Please make sure that you have read this before installing and using . Device Power Connection: Just only connect DVR with power supply, the power of cameras and monitors are all supplied by DVR, aviation connectors is built-in DC 12V output. ★... -
Page 13: Main Functions
2. Main Functions Main Sub-Item Instructions Recording Video Channel 5Channel video + Audio recording synchronously； Sub-System Support 1*1080P IPC, 4*720P(1280*720),4*D1(704*576),4*HD1(704*288), Resolution 4*CIF（352*288）；Each channel is individually adjustable. Image Quality 0-7 levels, 0 is the highest level. Overlays information such as date time and vehicle ID Loop Rec Support SD card loop recording, loop cover previous video Record Mode... -
Page 14: Parameter Sheet
3. Parameter Sheet Item Parameter Linux Language Chinese/English/Others (can be customized) Video Compression H.264 Compression Mode Overlays information such as date time and vehicle ID Graphical User Can connect to external LED screen. Setup system parameters with the remote Interface control. - Page 15 Support Built-in 3G/4G network, WCDMA,CDMA2000,TDD-LTE,FDD-LTE... Wireless transfer Support Built-in/External WIFI,Compatible with GPRS,EDGE Position Support Built GPS/BD Module,can make playback analysis of vehicle routing G-Sensor Support G-sensor 2.5’’ HDD+ SD Card,each max 2TB HDD + 128GB SD Card mirror recording to Storage protect data from loss Support USB flash disk updating,SD card upgrade , OTA remote upgrade...
-
Page 16: Real-Time Video Interface Description
4. Real-time video interface description 4.1 Real-time monitoring interface: Real-time monitoring interface status icons are displayed as follows : 4.2 Various signal status icons as follows: G Signal status: 4G Signal status: GPS Signal status: WIFI Signal status: Center connect succeed status: SIM card Not Exit Status: - 15 -... -
Page 17: Operation Interface Setup
Text scheduling real-time interface displays : ******************************************************************************************* Preview screen, press the remote control - on - next - right, will lock remote control, there will be an underscore prompts between the date and time; Press the remote control - on - next - left to unlock. Video loss or reboot the device will unlock; ******************************************************************************************* 5. -
Page 18: System Main Menu
5.2 System Main Menu The main menu includes: Search, System setup, Rec setup, Network setup, Alarm setup, Peripheral setup, System Tools, System Information, as below: 5.3 Search Query menu includes: Record, Picture, Log, Dispatch, call records - 17 -... -
Page 19: Video Search
5.3.1 Video Search **** Green color display indicates current day and time exist video file **** “Search Date”: Press the number key to enter date, default is current date. “Start Time”: Press the number key to enter date, default is 00:00. “End Time”: Press the number key to enter date, default is 23:59. -
Page 20: Picture Search
5.3.2 Picture Search This menu is mainly for searching the screenshot pictures. Zoom up single full screen will auto screen capture by default , it will be triggered by the alarm linkage or manually operate. **** Pictures and device log all save in the second partition **** 5.3.3 Log Query This menu is to query device operation and working log , you can choose the same type log via log categories. -
Page 21: Dispatch
5.3.4 Dispatch This menu is to query the device scheduling information, text messages, etc. 5.3.5 Call Records This menu is to query log of device voice calls recording. 5.4 System Setup Under System Setup menu includes: Power, time setup, user setup, terminal setup (menu setup and modifying need to choose save to take effect) 5.4.1Power Management This menu is to setup Power management modes and power distribution. -
Page 22: Time Set
"Power mode":press the number keys to select the type, the default is ignition mode. "Delay Off": Press the number keys to enter the time, the default is 5 minutes, can be set to 1440 minutes "Screen time”: Press the number keys to enter the time, the default is 60 minutes, can be set to 0-1440 minutes "Power On": Press the number key to enter time, setup the timer start time "Power Off": Press the number key to enter time, setup the timer off time... -
Page 23: User Management
5.4.3 User Management "Password Enable": You can enable or disable password authentication to access the menu. Modify or setup password of users and the administrator by remote control. **** ADMIN Pass : 666666, USER Pass : 000000 **** 5.4.4 Terminal Setup By remote control input settings: device number, phone number, license plate number, license plate color, chassis number, vehicle type, the provincial domain ID, the City ID, driver's license number, authorization code, company name, telephone service, terminal type, manufacturer ID, terminal ID, the... -
Page 24: Rec Setup
5.5 REC Setup Recording setup menu includes: basic setup, Main stream, Sub stream, mirror Recording, time recording, disk management(configuration and modification must select Save to take effect) 5.5.1 Basic Setup This menu is to setup the basic video, audio and video parameters and can change into standard definition, AHD high definition and mixed mode. -
Page 25: Mirror Record
"Alarm pre-recorded": pre-recorded alarm recording time of 0-60 seconds to setup, press number keys to setup. "Alarm delay": alarm delay recording time, 120-300 seconds to set up, press number keys to setup. "Camera Type ": Can switch the status of standard definition , high definition or mixed camera input. Attention : If the camera type and DVR setting mode(AHD HD/Analog/Mixture) don’t match, then it will show “video lost”, In Mixture mode, 1,2CHANNEL is AHD high definition input, 3,4CHANNEL is analog... -
Page 26: Sub-Stream
5.5.4 Sub-stream This menu is used to set the parameters of the transmission stream. "Resolution" Setup the transmission resolution, press [OK] key to enter. "FPS" Setup the transmission time frames, press [OK] key to enter. "Image quality" setup transmission quality grade, press [OK] key to enter. **** Sub-stream is the code stream which device upload via 3G/4G, high definition main code stream can be chose in the client-side platform **** 5.5.5 Time Record Setup... -
Page 27: Network Set
5.5.6 Disk Management When there are multiple disks, they can be set up recording parameters and priority grade. "REC": Setup main video or sub video in disk. "Pri": Setup the priority of different memory, enabling loop recording, function missing video recording. 5.6 Network Set Including: Center setup,Local Network ,3G setup ,WIFI setup ,FTP setup and IPC setup. -
Page 28: Local Network Setup
“Monitoring Center”:Set 3G /4G Video Center IP or domain,port information etc, “Network Type”:Set 3G network type, IP address/Domain optional; “Center IP”:3G Server IP/Domain setup. Press right key to enter keyboard interface,input the numbers via remote controller,then press [OK] for setting,; “Port”:Communication port between 3G device and Server,must be same with server configuration;... -
Page 29: 4G Setup
“IP”\“Mask”\“Gateway”\ “DNS1” \“DNS2”\“MAC”:IP,Mask,Gateway,MAC setting for LAN network testing. Attention: When net cable directly connect to the device, only can use 4PIN definition net cable (please see more definition in the addenda), otherwise it will lead device dead. 5.6.3 3G/4G Setup 3G/4G Network Configuration “Enable”:3G/4G On/Off Setting,Press [OK] for choosing;... -
Page 30: Ipc Setup
“WIFI-EN”:WIFI On/Off Setting,Press [OK] for choosing; “Encr-EN”: WIFI encryption ON/Off Setting,press [OK] for choosing; “Au-Mode”: WIFI Authentication mode setting,Please choose same one with your router, “Enc-Type”: WIFI Encryption type setting,Please choose the one same with your router, “IP”\“Mask”\“Gateway”:WIFI IP/Mask/Gateway setting “SSID”: Input Your WIFI SSID, “PWD”: Same with your WIFI password, **** According to the specific configuration of WIFI network environment, please pay attention to... -
Page 31: Ftp Setup
5.6.6 FTP Setup FTP Server setup for OTA Automatically grading when new firmware upgrading in FTP Server; “IP Address” “Port” “ User ” “ Password”: Please do configuration of IP Add, port,user,password according FTP Server Setup. 5.7 Alarm Setup Including: IO/Speed/Temperature/Accel/Voltage/Output 5.7.1 IO Alarm Each channel alarm enable/level/time delay/Linkage information setting;... - Page 32 “Enable”:Alarm Trigger enable on/off and alarm type, press [OK] for changing; “Level”:Choose Alarm trigger level,High/Low Level optional,press [OK] for optional; “ Delay”:When alarm trigger,if need delay alarm trigger,time can be set to reduce error alarm, press [OK] for changing; “ Record”:Record set when alarm trigger, press [OK] for changing; “...
-
Page 33: Speed Alarm
5.7.2 Speed Alarm High/Low Speed or illegal driving alarm can be set. “ Speed Source”: The method to get speed, GPS/Pulse Signal Optional, Press [OK] for changing; “ Pulse Number”:Must set Pulse factor for the standard if using Pulse to get car speed information,press Numbers for changing,can search vehicle data or constant speed by several times setting for a certain number “... -
Page 34: G-Sensor
5.7.4 G-sensor SET G-sensor information of alarm threshold and linkage actions. Before configuration, need to calibrate the current state first, then modify the alarm threshold. 5.7.5 Voltage Alarm Low/High Voltage alarm. Voltage abnormal delay shutdown: it means the voltage is kept below 8V, automatic shutdown time, this can effectively protect the battery, to avoid abnormal conditions caused by the battery voltage shortage, prolong the service life of the battery. -
Page 35: Peripheral Set
“Threshold ”: Main is area alarm percentage, generally set 1 or 2, representing 1% or 2% area change images move,it will trigger motion detection alarm. “Sensitivity”： 0-7 levels, 0 is the highest level, 7 is the lowest level. Generally suggest to set 1, the big ger number you choose ,the lower the sensitivity will be, then it’s not easy to alarm as well. -
Page 36: Ptz
5.8.1 PTZ PTZ Camera parameter configuration “ Protocol Type”:The Protocol of PTZ Camera support option,Press [OK] for changing; “ ADD Code”:choose PTZ Camera Address code,press Number for changing; “ Preset”:Choose PTZ Camera Preset code,press number for changing; ** When using remote controller to control PTZ, after configuring parameters, need to zoom in single screen first, then press PTZ ,then use the direction keyboard to control ** 5.8.2 Oil Reserved oil set menu, can be set on the serial port currently... -
Page 37: Tools
“ Peripheral”:The external device type option,press [OK] For Changing; “ Baud Rate”:Choose Baud Rate of external device,press [OK] for changing; “ Data Bit”: Choose the Data bit of external device, press [OK] for changing; “ Stop Bit”:Choose the Stop bit of external device, press [OK] for changing; “... -
Page 38: Format
5.9.2 FORMAT Format Disk choice, device will reboot disk after confirming, log and pictures and other related info will be reserved. Attention: DISK 1 is SD Card , DISK 2 is HDD. Device will format automatically when it starts, new HDD or SD card, can be formatted on the computer, in general, it doesn’t need format disk in DVR by manual. -
Page 39: Tel Set
“Import”:Import parameters from HDD or SD Card to current device.Import the system configuration parameters which has set up and restore the factory settings to the factory states “Export”:Export current device parameters to HDD or SD Card; “Default”:Default to factory setting; This operation will clear all the setting on the device. If quantity Devices with same setting,please using Parameter Export/Import for configuration, after setting one device, export these parameters to HDD or SD Card then import to other rest devices to be fast setting. - Page 40 - 39 -...
-
Page 41: Mainconfiguration Instructions
5.11 Mainconfiguration instructions SIM card dial-up parameters should be set in If need to change the server, press F2 to enter 3/4G Setup, customers can consult APN and other quick settings page , device number and mobile phone related parameters from SIM card operators. number are the same to set as the device ID, the monitoring center can change the IP for the server;... -
Page 42: Device Installation
6. Device Installation 6.1 Power Cable Connection Attention The recorder is DC power supply; please attention the positive and negative polar. The voltage is 7V~48V.Do not insert voltage that beyond this range. Under low voltage the recorder doesn’t work, under high voltage will be harm to the recorder. Please make sure the recorder is connect with the car power directly. -
Page 43: Audio/Video Interface Definition
6.2 Audio/Video Interface Definition The device support channel AV1~ AV4.The aviation joint can adapt severe environment in the vehicles; The power in the rear panel, IO and other PIN of the interface below: Extension interface PIN order refers to Figure 24PIN, 24PIN and 16PIN detailed definitions are as below: - 42 -... -
Page 44: Alarm In/Output Connection Mode
6.3 Alarm In/Output Connection Mode Device have 8CH Alarm Input Interface, 24 PIN I/O Interface Definition is IN1 - IN8 . Alarm input usually using High Level to trigger, connect SOS button,Kinds of vehicle driving status such as: Braking,Turning,Door open etc; The following is the brake detection diagram. - Page 45 6.5. Hard Disk box installation instructions 1. Turn over the hard disk box, dismantle 2 screws in the side and underside,as shown <Figure 1>. 2. Install 4 screws on 2.5inch hard disk, remove the hard disk box from one side bracket, as shown in <Figure 2>.
-
Page 46: Faq
7. FAQ Q:When Device issue appear,you are confused on how to solve it. A:Check Device Item No & Firmware Version,sent back to us with detail description of issue.Our Technical Team will handle it. More detail you described,easier for us to solve it quickly. Q:Video Output Lost A:1.Check situation of DVR:Device Input Power;Power Cable Connection;GND Connect to battery;fuse;RED &... -
Page 47: Wireless Module Related Faq
4)If working environment not good will related to no GPS Information or wrong information; Q:Deviation of GPS Location on Map? A:The signal is effective if the GPS module has been positioning, there are so many reasons caused bias, government restriction, permissible error, GPS signal break off, The actual satellite map error occurred for the security, GPS Correction can solve the problem. -
Page 48: Other Related Questions
Tel: +1 (604) 473-7758 www.tt-i.info 2016 TTI All rights reserved. TTI is a registered trademark and the TTI logo are trademarks of TTI Inc. All other trademarks mentioned herein are property of © their respective owners. Specifications are subject to change without notice.