Summary of Contents for SHOWTEC Titan Strobe blaze
- Page 1 MANUAL ENGLISH Titan Strobe BLAZE Ordercode: 40297 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
-
Page 2: Table Of Contents
Titan Strobe BLAZE Table of contents Warning ....................................2 Safety Instructions ................................. 2 Operating Determinations ............................4 Rigging .................................... 4 Connection with the mains............................5 Return Procedure ................................5 Claims ....................................5 Description of the device ..............................6 Features ..................................6 Frontside.................................. -
Page 3: Warning
Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing. Your shipment includes: Showtec Titan Strobe BLAZE Pro power cable (1,5 m) ... - Page 4 • If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Showtec dealer for service.
-
Page 5: Operating Determinations
When rigging, derigging or servicing the Titan Strobe, always make sure that the area below the installation site is secured and that there are not any unauthorized people around. The Titan Strobe BLAZE can be mounted to any kind of truss with a clamp. Improper installation can cause serious injuries and/or damage of property! -
Page 6: Connection With The Mains
Titan Strobe BLAZE Connection with the mains Connect the device to the mains with the power-plug. Always check if the right color cable is connected to the right place. International EU Cable UK Cable US Cable BROWN YELLOW/COPPER PHASE BLUE... -
Page 7: Description Of The Device
The RGB LEDs provide a colorful illumination of the reflector. The pre-programmed color macros are divided into zones, in order to create color flows. The built-in lightning simulation, linear and random strobe effects, blinder and single flash mode make the new Titan Strobe BLAZE the complete package for all professional lighting operators. -
Page 8: Backside
11) 5-pin DMX signal connector IN Installation Remove all packing materials from the Titan Strobe BLAZE. Check if all foam and plastic padding is removed. Connect all cables. Do not supply power before the whole system is set up and connected properly. -
Page 9: Control Modes
Titan Strobe BLAZE Control Modes There are 3 modes: • Manual • Master/Slave • DMX-512/RDM (3CH, 5CH, 9CH) One Titan Strobe (Manual) 01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation. -
Page 10: Multiple Titan Strobes (Dmx Control)
Titan Strobe BLAZE Multiple Titan Strobes (DMX Control) 01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) Use a 3-pin/5-pin XLR cable to connect the Titan Strobes and other devices. -
Page 11: Fixture Linking
Titan Strobe BLAZE Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support. -
Page 12: Control Panel
Titan Strobe BLAZE The Titan Strobe BLAZE can be operated with a controller in control mode or without the controller in stand-alone mode. Control Panel A) LCD display OK button C) UP button D) DOWN button DMX LED indicator Power LED indicator Fig. -
Page 13: Menu Overview
Titan Strobe BLAZE Menu Overview Ordercode: 40297... -
Page 14: Main Menu Options
Titan Strobe BLAZE Main Menu Options 1. Operation modes 2. DMX Address (DMX settings) 3. Channel Modes (DMX settings) 4. DMX Error (DMX settings) 5. Strobe Brightness (Manual mode) 6. Strobe Frequency (Manual mode) 7. LED Master Dimmer (Manual mode) 8. -
Page 15: Dmx Error (Dmx Settings)
Titan Strobe BLAZE 4. DMX Error (DMX Settings) With this menu you can determine what the Titan Strobe will do in case of a DMX signal error. 01) Press the UP/DOWN buttons until the display shows NO DMX. 02) Press the OK button to open the menu. -
Page 16: Led Color Switch/Color Flow Settings (Manual Mode)
Titan Strobe BLAZE 10. LED Color Switch/Color Flow Settings (Manual Mode) With this menu you can set whether the Titan Strobe performs a color switch or a color flow. 01) Press the UP/DOWN buttons until the display shows C_FADE. 02) Press the OK button to open the menu. -
Page 17: Channels
Titan Strobe BLAZE 5 Channels Channel 1 – Strobe dimmer Not functional 5-255 From dark to brightest Channel 2 – Strobe frequency CH1 must be open. Not functional 5-255 Strobe frequency, from low to high frequency Channel 3 – Strobe mode CH1 and CH2 must be open. -
Page 18: Channels
Titan Strobe BLAZE 9 Channels Channel 1 – Strobe dimmer Not functional 5-255 From dark to brightest Channel 2 – Strobe frequency CH1 must be open. Not functional 5-255 Strobe frequency, from low to high frequency Channel 3 – Strobe mode CH1 and CH2 must be open. -
Page 19: Maintenance
04) The electric power supply cables must not show any damages or material fatigue. The Titan Strobe BLAZE requires almost no maintenance. However, you should keep the unit clean. Otherwise, the fixture’s light output will be significantly reduced. Disconnect the mains power supply, and then wipe the cover with a damp cloth. -
Page 20: No Response To Dmx
Titan Strobe BLAZE No Response to DMX Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card malfunction. 01) Check the DMX setting. Make sure that DMX addresses are correct. 02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power. -
Page 21: Product Specifications
Titan Strobe BLAZE Product Specifications Model: Showtec Titan Strobe BLAZE Input voltage: 240V AC, 50/60Hz Power consumption: 1800W (full output) DMX linking: 30pcs Dimensions: 495 x 160 x 265 mm (LxWxH) Weight: 5,9 kg Operating and Programming: Signal pin OUT:... -
Page 22: Dimensions
Titan Strobe BLAZE Dimensions Ordercode: 40297... - Page 23 Titan Strobe BLAZE Ordercode: 40297...
- Page 24 ©2017 Showtec...
Need help?
Do you have a question about the Titan Strobe blaze and is the answer not in the manual?
Questions and answers