Advertisement
Quick Links
Advertisement
Summary of Contents for Flameboss 300
- Page 1 FLAM EB OSS 300 MAN UAL Version 2.1 Download latest at FlameBoss.com/manuals...
- Page 2 SELV / LPS output. Use only the power adapter provided with the unit. Do not allow children to play with a Flame Boss 300. Keep away from children. Flame Boss 300 is not to be used by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge.
-
Page 3: Table Of Contents
WHAT’S INCLUDED - Flame Boss smoker controller - Blower ® - 110-240 volt AC power adapter - 3 blower adapters (Kamado kit only) - Pit Temperature probe - Blower manifold with fasteners (Universal kit only) - Meat Temperature probe www.FlameBoss.com... -
Page 4: Kamado - Blower Installation
KAMADO - BLOWER INSTALLATION www.FlameBoss.com... - Page 5 KAMADO - BLOWER INSTALLATION www.FlameBoss.com...
-
Page 6: Weber Smokey Mountain - Blower Installation
WEBER SMOKEY MOUNTAIN - BLOWER INSTALLATION www.FlameBoss.com... - Page 7 WEBER SMOKEY MOUNTAIN - BLOWER INSTALLATION www.FlameBoss.com...
-
Page 8: Pipe Thread Universal - Blower Installation
PIPE THREAD UNIVERSAL - BLOWER INSTALLATION www.FlameBoss.com... - Page 9 USING 3/4” BUSHING (NOT INCLUDED) www.FlameBoss.com...
- Page 10 TOP VENT ALMOST CLOSED www.FlameBoss.com...
-
Page 11: Connecting Your Flame Boss
CONNECTING YOUR FLAME BOSS ® www.FlameBoss.com... - Page 12 Temperature. With optional Y-cables and additional meat probes, you can monitor up to three different foods with your 300. Your Meat Temperatures will be shown in a rotating display and be identified by Mt1, Mt2, and Mt3 (switching every few seconds).
- Page 13 Pit Temperature goes outside this range from the Set [+/- 20] Temperature, the Pit Temp Alarm will trigger. WiFi Menu TCP/IP/MAC Menu Other Menu [Skip] [Skip] [Skip] Pg.14 Pg.18 Pg.19 MENU cycles through [Skip] and [Enter]. Pressing executes your choice. www.FlameBoss.com...
-
Page 14: Setting Up Wifi
Downloading ## % WiFi Status ID:12345 P:4321 2.02.001 AP Mode FB-##### Device is successfully Device is downloading Device is in Access Point connected if you see a firmware update. Mode. (##### is your your ID and Pin. controller’s device ID) www.FlameBoss.com... - Page 15 Station mode. Press to choose an option. [Access Point] WiFi Setup / Flame Boss App Open the Flame Boss app on your smartphone, tap on the Controllers tab, then tap on Connect in the upper left corner. Follow the steps shown. www.FlameBoss.com...
- Page 16 Your controller will switch to Station mode and use the WiFi network you configured to get online. Your computer or mobile device will disconnect from the Flame Boss access point and re-connect to a previously remembered WiFi network. If it does not you may need to connect to your old WiFi network again explicitly. www.FlameBoss.com...
- Page 17 MENU. (Space) (Enter), then press MENU. (Backspace) - Select the - Wait for the controller to connect and show your ID and Pin. If you make an error, select the (Backspace), then press MENU to remove the incorrect entry. www.FlameBoss.com...
- Page 18 IP address. MENU moves to next byte. This address will be blank if controller is not joined MENU on last byte moves to next screen. to a WiFi network. Network Mask [255.255.255.000 Network Gateway [192.168.001.001 www.FlameBoss.com...
- Page 19 Factory Reset their factory defaults, including WiFi information. Press Up 3 Times Display shows the current version of the installed firmware. Version 2.01.001 If you’re hungry for more details about the firmware updates, visit myflameboss.com/fw_releases. www.FlameBoss.com...
- Page 20 HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. www.FlameBoss.com...
- Page 21 ENJOY YOUR COOK...