Advertisement
Quick Links
These instructions are intended for use only by experienced professionals in the automotive
customizing business. Special tools and equipment, as well as specialized handling and care
of product during installation, may be required. Before beginning this installation, carefully read
through the following instructions. Use extreme care when cutting headliner material.
Check for wiring or other componentry above headliner material. Cut only where indicated.
Materials/ Tools required for this installation:
1. #2 Phillips screwdriver
3. T-15 TORX bit driver
5. T-45 TORX bit driver
7. Awl or similar tool
9. Audiovox Series 645/655 Video Module
INSTALLATION INSTRUCTION # 44-0022B
KEMCO
INSTALLATION INSTRUCTIONS
FOR
50-0230B-002
50-0230B-003
50-0230B-004
SUBURBAN
Overhead console with flip down TV
2. Powered screwdriver or drill with adapter
4. Razor knife or similar
6. 1/4" hex socket bit
8. 3/32" Drill bit
May 26, 1999
Printed in the U.S.A.
Advertisement
Summary of Contents for Kemco 50-0230B-002
-
Page 1: Installation Instructions
5. T-45 TORX bit driver 7. Awl or similar tool 9. Audiovox Series 645/655 Video Module INSTALLATION INSTRUCTION # 44-0022B KEMCO INSTALLATION INSTRUCTIONS 50-0230B-002 50-0230B-003 50-0230B-004 SUBURBAN Overhead console with flip down TV 2. Powered screwdriver or drill with adapter 4. - Page 2 MATERIALS PROVIDED FOR INSTALLATION: ITEM Description SCREW, # 8 X 3/4" HWH SCREW, # 6 X 1/2" PPH SCREW, # 6 X 3/8" PPH SCREW, # 8 X 2 1/2" PFH SCREW, #8 X 1 1/4" PWH MOUNTING BRACKET CONSOLE LIGHT LIGHT TRIM PLYWOOD, 3/8"...
- Page 3 FIGURE 1 2. Remove A/C control head from cloth covered trim ring on O.E M. console by depressing (4) four tabs on back of control assembly. See Figure 2. Discard cloth covered trim ring. FIGURE 3 I. PREPARATION OF VEHICLE INTERIOR 1.
- Page 4 6. Carefully trim headliner from the dome light area toward the front of vehicle as shown. See figure 4. Caution: Before cutting headliner material, check for wiring or other componentry above headliner. Cut only where indicated. FIGURE 5 8. Secure bracket to sheet metal frame using (4) four # 8 x 3/4"...
- Page 5 FIGURE 7 10. Remove and retain the (2) two door scuff plates on driver’s side. See Figure 8. FIGURE 9 9. If vehicle is equipped with an electronic compass, unsnap the wire harness clip and relocate toward center of vehicle. See Figure 7. FIGURE 8 11.
- Page 6 13. Measure 7” from rear A/C control opening toward the rear of vehicle. Using a razor knife, carefully cut an opening in the headliner that is 6” wide x 8 3/4” long. Make sure that the 6” width is centered in the vehicle. Caution: Before cutting headliner material, check for wiring or other componentry above headliner.
- Page 7 19. Install and route all video and audio cables, and any other added component requirements to their respective places in the vehicle. Refer to component installation instructions for wiring diagrams. The suggested routing of the video system cable is as follows: Above the headliner from rear A/C switch opening to B-pillar.
- Page 8 25. Raise video system into approximate position and connect all wiring to components. Route video cable through hole in mounting bracket. Connect wiring and cabling to video system per instructions included with video system. Make sure lights in video system operate with door jamb switch.