1. Manuals
  2. Brands
  3. Zoomnet Manuals
  4. Wireless Access Point
  5. Bgate-GT10-I
  6. User manual

Zoomnet Bgate-GT10-I User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Bgate-GT10-I
User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Bgate-GT10-I and is the answer not in the manual?

Questions and answers

Summary of Contents for Zoomnet Bgate-GT10-I

  • Page 1 Bgate-GT10-I User Manual...
  • Page 2 This document contains proprietary information of Zoomnet CORPORATION. Any reproduction, transfer, distribution, use or disclosure of this document or any portion of this document, in any form by any means, without the prior written consent of Zoomnet CORPORATION is prohibited.

  • Page 3: Fcc Statement

    You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. The minimum distance between this equipment and user should be 40 cm when the equipment operates. Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...
  • Page 4 Bgate-GT10-I Preface This manual mainly introduces how to configure the Bgate-GT10-I to users when they install AP device. It’s suggested to read this guide carefully before install the Bgate-GT10-I. This part includes the follow contents: Content introduction Readers Conventions Content introduction This document introduces WEB configuration, CLI confuguration and WEB upgrade.
  • Page 5 The device cannot be sold retail, to the general public or by mail order. It must be sold to dealers. It is installed by licensed professionals with special training according to Installation instruction provided by dealer or grantee. Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...

  • Page 6: Table Of Contents

    2.6.3 FIRMWARE UPGRADE ................. 6 2.6.4 CONFIGURATION BACKUP AND RESTORE ..........6 2.6.5 USER MANAGEMENT .................. 6 3 CLI CONFIGURATION ....................6 3.1 ENTERING CLI...................... 7 3.1.1 TELNET BY DOS INTERFACE ..............7 Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...
  • Page 7 5.8 BACKUP CONFIGURATION TO LOCAL PC ............. 19 5.9 FACTORY DEFAULT ..................20 5.10 SOFTWARE MIRROR ..................20 5.10.1 MIRRORING DESCRIPTION ..............20 6 UPGRADE ........................20 6.1 CONNECT AP CORRECTLY ................20 Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...
  • Page 8 Bgate-GT10-I 6.2 SET IP FOR COMPUTER ................... 21 6.3 LOGIN AP ......................21 6.4 FIRMWARE UPGRADE ..................21 6.5 CHECKING ......................22 Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...
  • Page 9 Table 3-1 Default Configuration of AP ....................6 Table 3-2 Necessary software tool ....................7 Table 3-3 Hyper Terminal parameters ....................8 Table 3-4 CLI Commands Overview List ................... 9 Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved VIII...

  • Page 10: Product Introduction

    Bgate-GT10-I, the product which zoomnet company launched is an 11n access point with high power and double frequency. Compared with traditional 54Mbps 11G and 108Mbps Super G products, Bgate-GT10-I provides a rate of 300Mbps. With such high bandwidth, it highly enhances data transmission’s effectiveness and reduces network delay in voice and video processing, network game playing, and video-on-line selecting.

  • Page 11: Web Configuration And Management

    Step1. Click [Start > Settings > Network Connections], and access the network settings UI. (Note: switch the menu to the classic view if you fail to find the settings option.) Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...

  • Page 12: Wireless Network Settings

    Step4. If the access controller is activated, the AP’s IP address can be assigned by AC remotelythrough DHCP. You may check Automatic gain IP address to gain the IP address assigned by DHCP Server. Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...

  • Page 13: Log On

    Click [Wireless Settings/ Wireless Status], access to page of Wireless Status. 2.4.2 VAP settings Click [wireless settings/ VAP settings] to access the UI. 1）Status: Check it to activate the virtual AP Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...

  • Page 14: Advanced Settings

    12）RS IP address: Fill in the IP address of RS server 13）AS IP address: Fill in the IP address of AS server 2.4.4 Multi SSID-VLAN Binding Click [wireless settings/ Multi SSID-VLAN binding] to access the UI and set its parameters. Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...

  • Page 15: Tcp/Ip Settings

    2.6.5 User Management Open [Device Menagement/ User Management] to access the UI. CLI Configuration Obtain IP address for AP according to the network environment. Table 3-1 Default Configuration of AP Iterms Description Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...

  • Page 16: Entering Cli

    Input the username and password, then access to telnet management UI. Figure 3-2 Telnet management interface 3.1.2 Login through RS 232 Console Port Click [Start/Programs/Accessories/Communication/Hyper Terminal] to access to hyper terminal UI Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...

  • Page 17: Login By Securecrt Tool

    SecureCRT is used to login device by console port or telnet. We take logining device by console port as an example. Run the SecureCRT tool, and input the correct username and password to access the UI Username: root Password: password Figure 3-4 Logining interface Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...

  • Page 18: Cli Commands

    Options: [[-]broadcast [ADDRESS]] [[-]pointopoint [ADDRESS]] [netmask ADDRESS] [dstaddr ADDRESS] [hw ether ADDRESS] [metric NN] [mtu NN] [[-]trailers] [[-]arp] [[-]allmulti] [multicast] [[-]promisc] [txqueuelen NN] [[-]dynamic] [mem_start NN] [io_addr NN] [irq NN] Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...

  • Page 19: Iwconfig

    The usages are similar to ifconfig, but they are only for 802.11 devices. Online help is as followss: # iwconfig --help Usage: iwconfig [interface] interface essid {NNN|any|on|off} interface mode {managed|ad-hoc|master|...} Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...
  • Page 20 Instance: #iwconfig wifi0_wlan0 rate 54M enc: Set or manage WEP secret key. It can be set 4 keys on each radio module, you can choose 1~4 to activate the key. Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...

  • Page 21: Iwpriv

    2. Set the chainmask value for sending and receiving For the diversity receiver or MIMO device, this command is used to choose and configure its wireless link or antenna. #iwpriv wifiN txchainmask mask #iwpriv wifiN rxchainmask mask Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...
  • Page 22 Shared Key (WEP) Authentication 802.1x Authentication Auto Select/accept authentication (used by host_apd) WPA PSK with 802.1x PSK Instance: #iwpriv wifi0_wlan0 authmode 2 #iwpriv wifi0_wlan0 get_authmode wifi0_wlan0 get_authmode:2 （2）WEP operation. Command format: Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...

  • Page 23: Wlanconfig

    2. Display VAP parameters Only enable the VAP, it can display the parameters normally, the instance of enabling VAP is described as follows: # iwconfig wlan0 essid asdddd DES SSID SET=asdddd Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...

  • Page 24: Iwlist

    [interface] frequency [interface] channel [interface] bitrate [interface] rate [interface] encryption [interface] keys [interface] power [interface] txpower [interface] retry [interface] ap [interface] accesspoints [interface] peers [interface] event [interface] auth [interface] wpakeys Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...

  • Page 25: Synthesis Instance

    Login the device, input username and password. Input “fitap”or “fatap” according to the AP mode Input “reboot” Enter the command line and input “fitap”or “fatap” then press<Enter>. It can set the AP mode. Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...

  • Page 26: Common Operation In Fat Ap Mode

    4）WMM: Enable or disable the WMM control 5） Security: Click<Edit> button then select authentication method, encryption algorithm and secret key 6）APPLY: After finish setting, click <APPLY> button to take the new configuration go into effect Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...

  • Page 27: Modify Wireless Parameters

    “desired_mode” is a anticipant mode, which can be selected from AUTO, 11A, 11NAHT20, 11NAHT40PLUS, 11NAHT40MINUS, 11B,1G,1NGHT20, 11NGHT40PLUS, and 11NGHT40MINUS. Step3. Use command iwpriv interface get_mode to check the VAP mode. Figure 5-2 Check VAP mode Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...

  • Page 28: Check And Modify Vap Channel

    Step1. Login the WEB page of AP Step2. Click [Device Management/Configuration Backup and Restorer] to access the UI. Step3. Click <Backup> button, and choose a local path to save the configuration. Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...

  • Page 29: Factory Default

    ZOOMNETWORK: Trade name Bgate-GT10-I: Equipment model AP9344-Rev.D: Number of hardware version V2.0.2-A100105: Number of software version Upgrade 6.1 Connect AP Correctly Follow the figure below to connect the AP correctly Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...

  • Page 30: Set Ip For Computer

    4. Access the configuration UI’s System Status page. 6.4 Firmware Upgrade Caution： ： ： ： Don’t power off or reboot AP device when it is upgarding, otherwise it will be damaged and cannot be recovered. Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...

  • Page 31: Checking

    2) Click <Browse> , choose the upgrade package” RNAA891.1.0.0C4.xbin”, and then click <Upgrade>. 3) upgrading is finish. 6.5 Checking When progress bar is 100% completed, check whether the version of AP is correct or not. Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved...

Table of Contents