Summary of Contents for Sigma CYBER 5500 II DVI
- Page 1 SIGMA CYBER 5500 II DVI User’s Manual Version 1.0 Notice This device has been approved by EMI for home. It can be used in all areas including residential area.
-
Page 2: Table Of Contents
Table of Contents Chapter 1 Introduction • Contents of the package • Features of SIGMA CYBER 5500 DVI • System Configuration and Each Part Description Chapter 2 Installation • Installation of display drivers Windows 98 Windows 2000 Windows NT • Installation of application programs Chapter 3 How to use programs •... -
Page 3: Chapter 1 Introduction
Chapter 1. Introduction Contents of the package Thank you for purchasing the Sigma Cyber 5500 DVI. Please make sure that you have a full content of Sigma Cyber 5500 DVI after removing the package. Sigma Cyber 5500 DVI Board It is equipped in AGP slot of system main board and displays the computer screen on your TV. -
Page 4: Features Of Sigma Cyber 5500 Dvi
Features of Sigma CYBER 5500 DVI * Powered by nVIDIA’s GeForce 2 MX * Two new Hypertexel pipelines * Up to 20million triangles per second at peak rates * Full scene anti-aliasing and Per-Pixel Shading * Maximum resolution up to 2048x1536 at 75 Hz... -
Page 5: System Configuration And Each Part Description
System Configuration and Each Part Description ! ! ! ! System Configuration To use Sigma Cyber 5500 DVI effectively, you need the following configuration. CPU & Main board IBM-PC compatible main board in compliance with AGP 2.0 (More than Intel 440BX or VIA Apollo pro) - Page 6 ! ! ! ! Part Description Figure1. Sigma Cyber 5500 DVI 1. VGA Monitor output is connected to the monitor and outputs video signals. 2. Composite/S-VHS TV output is to transmit PC screen into Composite/S-VHS signals. 3. DVI-I Dual Link output (24 pins) accepts either a 12- or 24 - pin DVI plug connector or new type of analog plug connector.
-
Page 7: Chapter 2 Installation
Installation of display drivers Windows 98 In case of installing the SIGMA CYBER 5500 with Windows 98 If you have installed Windows 98 newly, your system recognizes the video card as “standard PCI graphics adapter”. If it has not been set correctly, switch display to “standard PCI graphics adapter and proceed the following procedures. - Page 8 7. When it turns back to the “device driver update wizard”, click “Next”. 8. If it recognizes “SIGMA CYBER 5500 DVI”, click “ next” again. Click “Finish”. 10. If a dialog box appears asking if you want to restart your system, select “Yes”.
- Page 9 5. Type “E:\WIN9X” then click “O.K” (E is assumed as the letter of your CD-ROM Drive) 6. If “SIGMA CYBER 5500” is in “Display adopter” dialog box, click “O.K”. The appropriate drivers will be copied and the system will be configured automatically.
- Page 10 7. If a dialog box appears asking if you want to restart your system, select “Yes”.
-
Page 11: Windows 2000
Windows 2000 In case of installing Windows 2000 in your system that has the SIGMA CYBER 5500 DVI When you install Windows 2000 in condition that the SIGMA CYBER 5500 DVI has been installed, Adapter type is set to “VGA”. You can find ‘Video controller (VGA compatible) in “Other device”... - Page 12 In case of installing the SIGMACOM CYBER 5500 DVI in Windows 2000 When you remove the existing VGA card from your system and newly install the SIGMA CYBER 5500 DVI “New hardware found” dialog box appears and “add new hardware wizard”...
-
Page 13: Windows Nt
Windows NT4.0 Note " To install the SIGMA CYBER 5500 DVI in Windows NT 4.0, you should have Service pack 3 or higher. Start Windows NT4.0. Insert the installation CD into your CD-ROM Drive. Click the right mouse button on the Windows screen and select “properties” on the dialog box. - Page 14 Select “Yes” if a dialog box that asks to install a third party drivers. 10. All appropriate files are then copied to the hard disk. When all files are copied, go back to the Display Properties box by clicking Close. 11.
-
Page 15: Installation Of Application Programs
Installation of application programs Installation of application programs for SIGMA CYBER 5500 DVI Insert the installation CD into your CD-ROM Drive. Open “My Computer” in Windows 95 or Windows 98 and select your CD-ROM Drive. Run “SETUP.EXE” in “SIGMACOM” folder of the “CYBER 5500”. -
Page 16: Chapter 3 How To Use Programs
Chapter 3 How to use Utility programs Using Sigma Cyber 5500 DVI’s utilities This is a utility program that sets display properties and 3D functions provided by the CYBER 5500 DVI. When selecting “GeFORCE 2 MX” tab right after clicking “Advanced” in “Settings” of the “Display properties”, the following dialog box that shows hardware information, driver version and... - Page 17 Color management This is a utility to adjust a color (Gamma value) and contrast value. Shows the screen condition that is controlled by the below bars. Sets a color to control among Red, Blue, Green and all three colors. Controls the brightness. Controls the contrast.
- Page 18 DirectX 3D settings This is to specify each detailed item for 3D acceleration. Selects MIPMAP level. MIPMAP detail level (best quality#$best speed) adjusts 5 levels of MIPMAP. Saves the configuration. Restores to the default value. Sets Texel arrangement and PCI texture memory size.
- Page 19 Open GL settings This is to set the buffer and video memory for OpenGL.
- Page 20 Overlay color control This is to control the overlay color when watching TV or VCD.
- Page 21 Other options This sets the display drivers and icon images for display tabs.
-
Page 22: Twinview Function
TwinView Function TwinView is able to support two display devices simultaneously to achieve multiple display function. Unlike other solutions that you have to plug two cards in a system, TwinView function can achieve a multiple display by only one card. You can connect DVI enabled Display to DVI Dial Link output or TV to Composite/TV output. - Page 23 2. Select desired TwinView mode as “Extended Desktop” or “Clone” instead of “Standard”. “Extended Desktop” mode lets a desktop area shared by all display devices. “Clone” mode let every device displayed the same image. 3. Press “OK”. The system will restart to achieve the function.
-
Page 24: Watching Video-Cd
Select ‘program’ of ‘Start’ in Windows 95 or 98. Run ‘Sigma VCD’ of ‘Sigma multimedia’ folder to display screen window and player panel as follows. SIGMA CD player is a S/W MPEG player to play Video, Audio CD and MIDI files. It also can be used for second language education with closed caption and screen captures. - Page 25 Makes the VCD player start in Interactive mode. It is supported with VCD 2.0 format. Iconization (minimize) Minimizes the SIGMA TV player panel. Help Shows the on-line help of SIGMA TV player. About Shows the information on the SIGMA TV player.
- Page 26 CD-ROM Eject Ejects CD-ROM drive tray. Online Help Displays help for Sigma VCD Player. Menu Displays configuration menu to play Sigma VCD Player. File Open Opens images in file. Plays interactive mode supported in Video CD 2.0 다. Interactive Mode Previous Track Plays the previous track.
-
Page 27: Listening To Mp3 Audio
Listening to MP3 audio (Sigma MP3) SIGMA MP3 player is a high quality MP3 player that runs in Windows environment. You can play all kinds of MP3 files at your convenience. Repeat Repeats a MP3 file when clicking the icon. -
Page 28: Addendum
VCD title that does not have interactive function, it refuses to play because the SIGMA VCD player is designed for interactive navigation. Q8: When running the SIGMA VCD player, the system is halted or gives an error message that it is quitted by mis-calculation.
Need help?
Do you have a question about the CYBER 5500 II DVI and is the answer not in the manual?
Questions and answers