Understanding The Control Panel; Programme Selector Knob And Programmed Start; Spin Exclusion Knob; Door Blocked Lamp - Indesit WT 102 Instructions For Installation And Use Manual

Top loading washing machine

Hide thumbs

Table Of Contents

Table of Contents

Available languages

Understanding the control panel

Here I'm in command

Making the right choice is important. And it's easy.

Programme selector knob

and programmed start

It is used to select the wash

programme.

T T T T T urn this knob c

urn this knob c

urn this knob cloc

urn this knob c

lockwise onl

loc

kwise onl

kwise only y y y y . . . . .

kwise onl

To select the programmes, the

mark situated on the knob must

be aligned with the symbol/

number that corresponds to the

desired programme.

Now press the on/off button G G G G G (I I I I I

position), and lamp H H H H H will begin

flashing. After 5 seconds, the

setting is accepted, lamp H H H H H stops

flashing (staying lit) and the

wash cycle begins.

If you want to interrupt the

programme in progress or set a

new one, select one of the

symbols

(Stop/Reset) and

wait 5 seconds: when the

cancellation

has

accepted, lamp H H H H H will flash, at

this point you can set the new

one or turn the appliance off,

should you wish to add some

garments, by then waiting for

approximately 2 minutes before

opening the appliance doors.

Y Y Y Y Y ou can also use this knob to

ou can also use this knob to

delay the start of the washing

machine.

Select one of the four positions

for the programmed start (after

9 hours, 6h, 3h or 1 hour), press

the on/off button G G G G G (I I I I I position)

and wait 5 seconds. This is

when the setting has been

accepted (lamp H H H H H stops flashing

and stays lit) and you can select

the programme you require.

Lamp H H H H H flashes in a special way

(2" on and 4" off) to indicate that

the programmed start has been

set. Even during this phase, you

can open the appliance door

and change the wash load.

After the wash cycle has been

set and accepted by the

washing

machine,

changes to the position of the

knob will be of no use (except

in the

Stop/Reset position).

Instructions for installation and use

5 5 5 5 5

T T T T T emperature contr

emperature contr

emperature control knob

emperature contr

It is used to set the wash

temperature indicated in the

programme table (on page 6).

It also allows you to reduce the

temperature recommended for

the selected programme, and

even to set a cold wash cycle

( snow symbol

Spin exclusion Knob

It is used to exclude the spin

cycle (by choosing symbol

) and/or to reduce the

spin speed of the selected

programme. The maximum

speed for the four types of

fabric ar

been

Fabric

Speed

Cotton

max rpm

Synthetics

800 rpm

Wool

600 rpm

Silk

none

Silk

In any case, the appliance

distributes the load at low

speed.

Pre-wash

With this button, you can pre-

wash on all programmes (see

page opposite) except the wool

programme and the special pro-

grammes. This function ex-

This function ex-

cludes the bleaching.

Easy

Easy iron

Easy

iron button

iron

button

This function allows your

washing to come out of the

machine without creases,

making it much easier to iron.

any

You can use it with program-

2-3

4-5-6

mes 2-3

2-3

2-3 (Cotton), 4-5-6

4-5-6 (Syn-

4-5-6

thetics).

ol knob

Press this button in program-

mes 4-5-6-7-8

4-5-6-7-8

4-5-6-7-8 and the wash

cycle will come to a stop on

symbol

. You can complete

it by pressing button E E E E E again.

Stain removal

Thanks to this command, the

washing machine will carry out

a more intensive wash that

optimises the effectiveness of the

liquid additives, thus allowing

more resistant stains to be

removed. When you press the

When you press the

S S S S S tain

tain

tain R R R R R emoval button,

tain

emoval button,

emoval button, you

emoval button,

cannot

run

the

the P P P P P re-wash

the

cannot

cannot run

run

run the

the

the Easy

Easy I I I I I ron

Easy

ron

ron function

the

Easy

ron

E) is enabled.

ON-OFF

When button G is pressed, the

washing machine is switched

on, when it is not the machine is

switched off.

T T T T T urning the mac

urning the mac

urning the machine off does

not cancel the selected

programme.

The knob

with your washing

machine's wash

programmes

The information contained in the

table is purely indicative. It could in

fact vary depending on the appliance

model, the quantity and type of

garments to wash, the hardness and

temperature of the mains water supply,

as well as the temperature of the

environment.

(see page 9)

ON-OFF lamp

Lamp H H H H H flashes when the

appliance is switched on and

awaiting a programme to be set.

A steady light means the

you

appliance has accepted the

re-wash

and

re-wash

re-wash and

and

selected programme.

unction (button

unction

(button

unction

(button

Door blocked lamp

This lamp indicates that the

washing machine door is

blocked to prevent it from being

opened accidentally. To avoid

any damages, you must wait for

hine off does

the lamp to switch itself off before

you open the door. You must

wait around two minutes.

Table of Contents

Show Quick Links

Hide quick links:

Table of Contents

Understanding The Control Panel; Programme Selector Knob And Programmed Start; Spin Exclusion Knob; Door Blocked Lamp - Indesit WT 102 Instructions For Installation And Use Manual

Available languages

Understanding the control panel

Spin exclusion Knob

Door blocked lamp

Hide quick links:

Related Manuals for Indesit WT 102

Related Content for Indesit WT 102

Table of Contents