Summary of Contents for Mercury Security SR10k
- Page 1 2355 MIRA MAR AVE. LONG BEACH, CA 90815-1755, (562) 986-9105 FAX (562) 986-9205 SR10k Mag-Stripe Access System Users Guide Page 1 Mercury Security © 2013 SR10k Doc. 10107-0007 Rev 1.08...
- Page 2 (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Mercury Security 2355 MIRA MAR AVE. LONG BEACH, CA 90815-1755 (562) 986-9105, FAX (562) 986-9205 www.mercury-security.com Page 2 ©...
-
Page 3: Overview
A Master Card places the SR10k into programming mode. Commands are entered via the keypad on the SR10k reader. In some cases the entry of user cards may also be required. A buzzer and two bicolor LEDs provide immediate feedback to the operator. - Page 4 OVERVIEW, continued Cipher Codes The SR10k supports up to 10 cipher codes. Each code is one to six digits in length - shorter codes are terminated with the '#' key. Cipher codes, like cards, are assigned a User Level, and like cards, may cause different output relay action depending on the direction of the code entry.
-
Page 5: Quick Start And Confi Guration Planning
Programming mode - the lower LED is ON steady green (amber if no Master Card) The upper LED is OFF if the SR10k is ready for a new command (wait for '*' key) The upper LED fl ashes red while waiting for keypad data entry, and is fl ashing green while waiting for card entry. -
Page 6: Programming Guide
The COMMAND ENTRY MODE is selected by passing a valid MASTER card through the reader. The intergral keypad allows direct data entry on the SR10k. The "*" key is used to start a new command entry. The '#' key terminates fi eld entry. For example, se- lecting user slot 3 for the the 4-digit user slot entry in Command 20 can be entered as 4 digits: '0','0','0','3', or it may be entered as '3', '#'. -
Page 7: Digits Long. Cipher Codes Shorter Than 6 Digits Are Terminated With The "#" Key. Just Like Cards Can Pro
Command 23 - Delete a range of cards (block deactivate) - select Command 23 - enter the fi rst user slot to delete (0000 through 1599) - enter the last user slot to delete (0000 through 1599) Page 7 © Mercury Security 2013 SR10k Doc. 10107-0007 Rev 1.08... - Page 8 'broadcast'; each SR10k must be set to a unique address 0 to 15. If the SR10k receiving confi gura- tion setting does not have a master card defi ned, a master card must be defi ned at that SR10k. Command 41 - Copy the Confi guration settings only - no card or cipher databases...
- Page 9 5 - In Facility Code Database Mode, the digit count specifi es the the number of card digits to read and verify. For example, setting the count to '3', the SR10k uses only the fi rst 3 digits on the card.
-
Page 10: Specifi Cations
- requiring another upward read (by any user Level) to release the locked condition. Add Level 2 users only if the lock/unlock function is desired. Page 10 © Mercury Security 2013 SR10k Doc. 10107-0007... - Page 11 Add Level 2 users only if the lock/unlock function is desired. Consider using Operating Mode 4 or 5 if restricted access is required, but the un- lock function is not. Page 11 © Mercury Security 2013 SR10k Doc. 10107-0007 Rev 1.08...
- Page 12 Upper LED assignment: The upper LED follows Input I1, displaying the status of the alarm panel: Open Contact is displayed as RED Closed Contact is displayed as GREEN Page 12 © Mercury Security 2013 SR10k Doc. 10107-0007 Rev 1.08...
-
Page 13: Operating Mode
Upper LED assignment: The upper LED follows Input I1, displaying the status of the alarm panel: Open Contact is displayed as RED Closed Contact is displayed as GREEN Page 13 © Mercury Security 2013 SR10k Doc. 10107-0007 Rev 1.08... - Page 14 Input assignments: The inputs are not used in this mode. Upper LED assignment: Output K1 off is displayed as RED, Output K1 on is displayed as GREEN Page 14 © Mercury Security 2013 SR10k Doc. 10107-0007 Rev 1.08...
- Page 15 User Level 1 cards are accepted only when a closed contact is presented to this input. Upper LED assignment: The upper LED follows Output K1 (and Output K2): Deenergized output is displayed as RED Energized output is displayed as GREEN. Page 15 © Mercury Security 2013 SR10k Doc. 10107-0007 Rev 1.08...
-
Page 16: Installation
Output K1 normally closed (NC) terminal. DIODE SELECTION: DIODE CURRENT RATING > 1X STRIKE CURRENT DIODE BREAK DOWN VOLTAGE : 4X STRIKE VOLTAGE DIODE 1N4001 (50V/1A) TYPICAL Page 16 © Mercury Security 2013 SR10k Doc. 10107-0007 Rev 1.08... -
Page 17: Maintenance
FOR 24 Vac STRIKE, PANASONIC ERZ-C07DK470 Maintenance The SR10k readers are designed to provide continuous service with minimal routine maintenance. However, contaminants (such as magnetic oxides from badges and dirt) tend to accumulate on the read head. Without regular cleaning, these contaminants will shorten the read head life and increase the probability of card read error. -
Page 18: Warranty
WARRANTY Mercury Security warrants that the product is free from defects in material and workmanship under normal use and service for two years from factory shipment. Mercury Security assumes no responsibility for prod- ucts damaged by improper handling or installation. This warranty is limited to the repair or replacement of the defective unit. -
Page 19: Jumper Setting
Communication Wiring: Maximum total cable length - 4,000 ft [1,200 m], 24 AWG 4 5 6 Set each interface to unique address. Install RS-485 termination jumper, J4, on the fi rst and last units only. Page 19 © Mercury Security 2013 SR10k Doc. 10107-0007 Rev 1.08...
Need help?
Do you have a question about the SR10k and is the answer not in the manual?
Questions and answers