Do you have a question about the X6S and is the answer not in the manual?
Questions and answers
Summary of Contents for inxni X6S
Page 1
Thank you for purchasing iBoto inxni Robotic Vacuum Cleaner. We believed that you will enjoy the product. Thank you for purchasing inxni Robotic Vacuum Cleaner. To obtain the best result of the product, please read this manual carefully as well as the quick start guide to get familiar with the product.
Page 2
Owner’s Manual Please read the manual carefully before using. SAVE THIS MANUAL FOR FUTURE REFERENCE. Thank you for choosing the inxni robotic vacuum cleaner...
5.7 Cleaning the Wheel Violation of Warranty Only inxni designated or authorized servicemen or service center is allowed to dismantle, repair or replace the Cleaner. 5.8 Cleaning the Sensor Don’t touch the power plug or the Cleaner when hands are wet as this may cause electrical shock.
Page 4
Screw driver or related tools shipped is not a toy and should not be used by children. 1.4 About Battery The cleaner can only work with the battery provided by original manufacturer and only genuine inxni battery should be used at all the time.
Page 5
Important: Do not disassemble the Cleaner. Disassembling the Cleaner will ner in the area close to staircase step, unsecured balcony, etc ensure that fence out those areas if needed. void the warranty. Only inxni or a party expressly authorized by inxni should perform service on this Cleaner.
2. Product Anatomy 2.2 Main Control Panel Description 2.1 Part Name and Package Contents Charging Pole Shoe Main Control Panel Battery Compartment Side Brush Front Wheel Ground Detection Sensors Wheel Floor Brush The Cleaner Charging Station Battery Adapter Main Brush *1pc *1pc *1pc...
3 to 4 time to enable the battery operates at its optimal point. 4. Use only the inxni genuine battery for the cleaner. If not, the non inxni battery may cause damage to the cleaner or unwanted accidents.
Page 8
4. Product Operating Mode 4.1.2 Operational Guideline for Touch button seen on top of the Cleaner 4.1 Product Cleaning Mode 4.1.1 Description: ON / OFF In the standby mode, touch the " " ON button, the cleaner will start to clean. Turn on and wait Touch the "...
Page 9
4.2.2 Automatic Charging: CLOCK Setup Touch the " " button, the cleaner will enter into current time setting mode. 1. APPS charging: Connect the cleaner with the Apple iPhone / iPad or and then touch the “HOME” button (Icon) as seen in the APPS. Touch the "...
5.3 Cleaning the Dirt and Dust inside the Dust-box 3. Take out the filter as indicated 4. should too much dust seen and gently bush off the dust seen inside the box and on the filter, 5.3.1 Removing the Dust Box on the filter into the garbage using gently rinse the filter with clean the brush provided in the...
5.7 Cleaning the Wheel 3. The main brush and floor 4. Remove the rubber sleeves brush can be removed separately from the main brush Completely as indicated. and the floor brush. (Warning: there is a metal Rubber Sleeve bearing inside the rubber sleeve. Don’t let it drop out from the Clean the front wheel and left &...
6.2 Common Issue or Problem 6. Product Trouble Shooting 6.1 Error Message Issue Problem Solutions Warning: 1. Error code will appear on the display seen on top of the cleaner should the cleaning cycling is interrupted The vacuum cleaner always goes 1.
Dimensions 340*340*90mm Note: inxni Reserve the right to change any wording; update the technology, design of product without advance notice. Refresh Tips: APPS may lose connection when the device is far from the mobile phone or ipad due to the network WiFi signal quality...
Page 14
Click “RETURN” on the mobile phone or pad as shown The operation interface of APPS is shown as the following Next Steps Select “OK” as shown in the figure below and start in the following figures figures. the next step after entering the password for connection. Enter the next APPS operating phase by clicking “OPEN MAP”...
Need help?
Do you have a question about the X6S and is the answer not in the manual?
Questions and answers