Related Manuals for Bzooma Amsterdam
Summary of Contents for Bzooma Amsterdam
- Page 1 Owner’s Manual Marketed in Australia and New Zealand by Bzooma Pty Ltd ABN 37 640 907 507...
-
Page 2: Table Of Contents
CONTENTS Bzooma Pty Ltd ....................................3 Manufacturing Profile ..................................3 Assembly ......................................4 Set Up........................................4 Install front wheel ....................................4 Alignment of the handle bars................................5 Install Pedals and Tighten Crank................................. 7 Front Brake Set Up ....................................7 Gear adjustments .................................... -
Page 3: Bzooma Pty Ltd
BZOOMA PTY LTD This User Manual is written and published according to the latest BZOOMA PTY LTD specifications. We will continue the policy of improvement and may make some changes in the design and specifications without notice. If you have any enquiries, please contact your local dealer or buy directly from this web site bzooma.com.au. -
Page 4: Assembly
ASSEMBLY Tools Required 8 mm ring spanner, 10 mm ring spanner, 15mm pedal spanner, 14 mm open end spanner, 5 mm hex key, 6 mm hex key, screw driver, cutters/plier Set Up. Install front wheel It is important that you fit the front wheel with the axle locked to the fork with the anti-rotation locking washers. (Washer with locating lug as shown in photo 1) The pressure of the nuts alone will not prevent the axle turning and pulling the electrical cable from the motor. - Page 5 Disconnect the brake cable to spread the brake pads ( see photo) which then allows the tyre to fit between the brake pads as the wheel drops into place. Drop the fork on to axle as shown in the photo 2. Ensure you observe the locating washer lug fits into place on the fork. Fork Fits Here The washer and nut go on last.
-
Page 6: Alignment Of The Handle Bars
Alignment of the handle bars. The handle bar assembly may need some small adjustment for the alignment of the headset to the front wheel. Slide the black lock device with your thumb to lift and release the handlebar adjustment. No tools are required. Use a 6 mm Alen key to loosen the handle bar stem. -
Page 7: Install Pedals And Tighten Crank
Install Pedals and Tighten Crank. Use a small amount of grease on the shaft before installing. Right and left pedals are marked because the thread differs on each. Tighten with the pedal spanner or 15mm spanner. Remember bicycle pedals tighten in a clock wise direction. Remove Plastic chrome cap on the crank and tighten with 14mm socket. -
Page 8: Gear Adjustments
Gear adjustments The factory sets up the gears perfectly, so if ever necessary; we recommend you have a bicycle workshop assist you with the adjustment of the gears. Gear Adjustment-all cable-operated Nexus and Alfine 4-, 7-, 8- and 11-speeds: Adjustment is made with the shifter in 4th gear for the 4, 7- and 8-speed hubs, 6th gear for the 11-speed hub. On the right side of the hub, just outboard of the sprocket, there is the "cassette joint pulley"... -
Page 9: Inspect Before Riding
INSPECT BEFORE RIDING 1.Check the grip. 2. Check tyre pressure. 3. Check brake pads for wear and replace in necessary. 4. Check Brakes for alignment of front pads and wear. 5. Check the tightness of chain and Q-release 6.Check the gear function. 7. -
Page 10: Maintenance
MAINTENANCE 1. Wipe the bike with a dry cloth, or neutral detergent. 2. Use lubricating oil for metal parts. 3. Wipe the plastics, paint coating part with a dishcloth. 4. Increase the frequency of lubricating oil in wet and humid areas See as below (Recommend 30SAE lubricating oil). - Page 11 BZOOMA Pty Ltd Dealer for inspection and service. Indications of abuse, accident, or unauthorised tampering with the machine power base mechanical, or electrical equipment, will void any claim. Bzooma Pty Ltd is not responsible for transport costs associated with obtaining service or repairs under this warranty.