1. Manuals
  2. Brands
  3. Sherpa Manuals
  4. Tiller
  5. STET1300
  6. Operating instructions manual

Sherpa STET1300 Operating Instructions Manual

Electric tiller
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SHERPA ELECTRIC TILLER
Model: STET1300
Operating Instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the STET1300 and is the answer not in the manual?

Questions and answers

Summary of Contents for Sherpa STET1300

  • Page 1 SHERPA ELECTRIC TILLER Model: STET1300 Operating Instructions...
  • Page 2 IMPORTANT! Please read and follow the operating instructions and safety information before using for the first time. DO NOT USE THIS MACHINE UNTIL YOU HAVE READ THE INSTRUCTIONS IN FULL. CAUTION! Always wear protective clothing, eye protection and gloves when operating this or any power tool. www.sherpatools.co.uk Help Line 0845 123 5844...
  • Page 3 1 1 1 1 1 1 1 1 6 6 6 6 8 8 8 8 5 5 5 5 7 7 7 7 2 2 2 2 2 2 2 2 7 7 7 7 3 3 3 3 4 4 4 4 2 2 2 2 1 1 1 1...
  • Page 4 3 3 3 3 4 4 4 4 1 2 1 2 1 2 1 2 1 0 1 0 1 0 1 0 1 3 1 3 1 3 1 3 B B B B 2 2 2 2 9 9 9 9 1 1 1 1 1 1 1 1 E E E E A A A A...

  • Page 5: Proper Use

    1. Important! Please refer to this booklet for the safety instructions. When using equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating manual with due care. Keep this manual in a safe place, so that the information is available at all times.

  • Page 6: Before Starting The Equipment

    4. Before starting the equipment Assembly (Fig. 3-6) Move the transport wheel into the lowest position (Fig. 3 / Item E). To do so, undo the • retaining screw (Fig. 3 / Item 13) and remove. Finally, replace the screw and tighten. Attach the bottom push bar (Fig.

  • Page 7: Operation

    5. Operation 5.1 Starting up Connect the machine’s power supply cable (Fig 7 / Item B) to the plug (Fig. 7 / Item A) and secure the power cable with the strain-relief clamp (Fig 7 / Item 5). Important! To prevent accidental start-up of the machine, the push-bar is equipped with a two-point switch (Fig. 8 / Item A) which must be pressed before the lever switch (Fig.

  • Page 8: Replacing The Power Cable

    Important! The tiller blades will continue to rotate for a few seconds after the motor is switched off. Never attempt to manually stop them. In the event that the rotating tiller blade strikes an object, immediately switch off the machine and wait for the tiller blades to come to a complete stop. Then inspect the condition of the tiller blades.
  • Page 9 Important! Wear working gloves when cleaning the machine. Use only genuine spare parts since otherwise the function and safety of the machine cannot be guaranteed. 7.3 Maintenance Ensure that all mounting components (i.e. screws, bolts, nuts etc.) are always tightened so that the machine can be safely operated at all times.

  • Page 10: Disposal And Recycling

    8. Disposal and recycling The unit is supplied in packaging to prevent it being damaged in transit. This packaging is raw material and can therefore be reused or can be recycled. The unit and its accessories are made of various types of material, such as metal and plastic. Defective components must be disposed of as special waste.

  • Page 11: Guarantee Certificate

    GUARANTEE CERTIFICATE Dear Customer, All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card.
  • Page 12 Notes...

Table of Contents