Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Lumberjack EP82-3
- Page 1 SAFETY AND OPERATING MANUAL POWER PLANER EP82-3 ORIGINAL INSTRUCTIONS EP82-3...
-
Page 2: Table Of Contents
TABLE OF CONTENTS General Power Tool Safety Warning ………………………………………01 Symbols & Cable Rating Chart………………………………………………..04 Machine Details and Product features……….……………………….….05 Assembly………………………………………………………………………………..06 Operation…………………………………………………………………………….…07 Maintenance and Service…………………………………………………….…08 Lumberjack Guarantee…………………………………………………………..11 Declaration of Conformity………………………………………………………13 Parts list…………………………………………………………………………………14 Parts diagram…………………………………………………………………………15 EP82-3... -
Page 3: General Power Tool Safety Warning
A wrench or a key left c) Do not expose power tools to rain or wet attached to a rotating part of the power tool may conditions. Water entering a power tool will result in personal injury. increase the risk of electric shock. EP82-3... - Page 4 Use power tools only with specifically operate the power tool. Power tools are designated battery packs. Use of any other dangerous in the hands of untrained users. battery packs may create a risk of injury or fire. EP82-3...
- Page 5 When using a cable reel, always unwind the c) Be aware when mounting any new blade cable completely. they are very sharp and can easily cut. EP82-3...
-
Page 6: Symbols & Cable Rating Chart
Caution! Wear a dust mask. Amperes 7.5M 0 – 2.0 2.1 – 3.4 3.5 - 5.0 5.1 – 7.1 7.1 – 12.0 12.1 – 20.0 EP82-3... -
Page 7: Machine Details And Product Features
9. Parallel Guide Gross Weight – 3.8KG 10. Moving Guard 11. V-Groove Nett Weight – 3.4KG 12. Blade protector 13. Front plane shoe Package Contents: 14. Blade head Dust Bag 15. Plane Blades 16. Belt Cover Parallel Guide Depth Guide EP82-3... -
Page 8: Assembly
All parts must be Attach the parallel Guide (If needed) to the machine properly mounted and all conditions fulfilled that as shown below. ensure faultless operation. Damaged protective Devices and parts must be immediately replaced by an authorised service centre. EP82-3... -
Page 9: Operation
- Guide the machine at constant speed across the material to be worked. Do not move too quickly, allow the machine enough time to plane the workpiece. - For large surfaces it is recommended to make several shallow cuts at a smaller planing depth. EP82-3... -
Page 10: Maintenance And Service
Next tighten your thumb as shown above, and the two outer screws first followed slide the cutter assembly in the by the centre screw. direction shown to remove it from the cylinder. EP82-3... - Page 11 Replacing the Drive Belt Should the cutter bind in the workpiece, it is probable that the drive belt needs changing. Should this be the case, please proceed as follows: - Remove the three securing screws, and pull off the cover. EP82-3...
- Page 12 - Replace the carbon brush slide the spade connection on to the end of the brush and hold in place with the plastic end cap. - Replace the holder carefully back into place, again DO NOT USE FORCE to avoid damaging the brush. EP82-3...
-
Page 13: Lumberjack Guarantee
1.2.8 The product has been purchased by you, 1.2.3 If asked to do so by lumberjack or as the guarantee is not transferable from a its Authorised Dealer, you return private sale. - Page 14 2. Claims Procedure 2.4 Please note that it is essential that the letter of claim reaches Lumberjack on the last day of this 2.1 In the first instance please contact the Authorised guarantee at the latest. Late claims will not be Dealer who supplied the product to you.
-
Page 15: Declaration Of Conformity
EP82-3... -
Page 16: Parts List
Caver degree pan Guide wind circle Adjusting handle Bearing 626RZ Plastic nut Rotor Adjusting handle cover Middle cover Spanner Bearing 608RZ Dust bag Bearing cover Nut M6 Screw ST3.9x12 Butterfly nut M6 Small belt wheel Assistance backer Belt Backing EP82-3... -
Page 17: Parts Diagram
Parts Diagram EP82-3...
Need help?
Do you have a question about the EP82-3 and is the answer not in the manual?
Questions and answers