Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Invisio V60
Summary of Contents for Invisio V60
- Page 1 INVISIO Multi-Com Control Unit USER MANUAL...
-
Page 2: Table Of Contents
Contents Disclaimer Incompatible Cables Overview Troubleshooting Getting Started System Reset Hear-Thru Control Attachment to Equipment Hear-Thru Volume Steps Fitting To Molle Webbing Cable Management Transmit Storage and Maintenance PTT Assignment Examples Received Audio Audio Tones Received Audio Swap Received Audio in Both Ears Glossary of Terms Mute All Radios Monitor Single Radio... -
Page 3: Disclaimer
User Manual or the Product shall be Product. limited to the price paid to INVISIO for the unit that caused any alleged The Product is designed exclusively for use by trained, professional damage. -
Page 4: Overview
To turn the hear-thru off, see PTT 3 section on hear-thru control. PTT 1 PTT 4 Turn Off To turn off the V60 disconnect the radio cable(s) or turn the PTT 2 radio off. Mode Button COM 1 COM 2... -
Page 5: Hear-Thru Control
• Turn the Hear-Thru Off or use Comfort Hearing when in noisy vehicles to reduce noise exposure. Caution Avoid acoustic feedback by turning the V60 off during • Using Enhanced Hearing for extended periods may headset fitting. increase noise exposure. -
Page 6: Transmit
Transmit PTT Assignment Examples Transmit Modes Example 1 The V60 has different ways of transmitting depending on the device and cables used. Examples include: COM Port PTT Assignment • Push-To-Talk (PTT) (e.g. 2-Way Radio) • Latching (Mute) (e.g. Intercom System) -
Page 7: Received Audio Swap
Received Audio Received Audio Swap How Audio is Received Swap Default Audio Left-Right Default audio routing can be swapped so that COM1 is in right ear and COM2 is in left ear via Default a key combination. Key Combo COM1 / Net1 Left 1. -
Page 8: Received Audio In Both Ears
• Press any assigned PTT button INVISIO IntelliCable ™ • Connect or disconnect any cable. Received audio in both ears mode only works when INVISIO IntelliCable™ settings are programmed to default audio routing. Note While transmitting in Default or Swapped audio mode, all Note received audio can be heard in one or both ears. -
Page 9: Monitor Single Radio
An error tone is heard when no cable is connected to the In Open Mic Mode, all receive audio is in the left ear only, as COM port being set to Monitor Single Radio Mode. the V60 is always transmitting. -
Page 10: Power Management
Power Management Incompatible Cables Power Source Warning Tones The V60 can be powered from either a battery A warning tone is heard when an incompatible pack (PS30) or a Radio. cable is connected. The audio tone stops when the cable is disconnected. -
Page 11: Troubleshooting
Audio Tone System Reset: 5 Beeps No Hear-thru • Press Mode Button • Press PTT button to check power is on Note Note Contact your representative if the issue is not resolved. System reset does not change the V60 firmware version. -
Page 12: Attachment To Equipment
Fitting To Molle Webbing Different Clip Place Through Webbing The V60 is supplied with a Molle clip as standard, The Molle clip is threaded through two Molle but different clips are available upon request. straps, with the hook grasping the lower Molle strap. -
Page 13: Cable Management
Protect from Force To avoid damaging the V60, store in a protected area without excess weight. Dry and Ventilated Store the V60 in a dry and ventilated area with caps removed to avoid moisture build-up in connectors. Clean in Fresh Water If the V60 becomes dirty or exposed to salt water, rinse in fresh water. -
Page 14: Glossary Of Terms
Audio Tones Glossary of Terms General Rule for Audio Tones The general rule for the V60 audio tones is based an on/off rule: INVISIO Bone Conduction Microphone. • On: 1 Beep Patented in-ear communication microphone for transmitting. • Off: 2 Beeps Hear-Thru •... - Page 15 www.invisio.com...
Need help?
Do you have a question about the V60 and is the answer not in the manual?
Questions and answers