Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Isel iPC25 - F
- Page 1 - F Operating instructions...
- Page 2 All rights reserved. No part of our publications may be reproduced in any form (print, photocopy or any other process) without the written permission of isel Germany AG or processed, reproduced or distributed using electronic systems.
-
Page 3: Table Of Contents
Safety symbols ......................... 1 Safety notices ........................1 Product description ......................2 Technical data ........................2 Interfaces iPC25 - F ......................4 Assembly and start-up ....................... 6 Installation dimensions ..................... 6 Switching on the control unit .................... 7 Recovering the operating system Windows® Embedded Standard 7 ......8 Maintenance and repair ..................... -
Page 4: General Notices
iPC25 operating instructions 1 General notices Carefully read the operating instructions to the end and follow the instructions given. Failure to observe these operating instructions can result in property damage, serious personal injury or death. Safety symbols Attention This symbol indicates that there is a risk to the life and health of personnel. Danger This symbol indicates that there is a risk to the material, machine and the environment. -
Page 5: Product Description
iPC25 operating instructions 2 Product description Technical data Item number 371066 xxxx 4001 (E) 4001 P (E) Dimensions (W x H x D): 210 x 90 x 190 mm Weight: 1.2 kg. Ambient temperature: 0°C to 35°C Relative humidity: max. 90% non condensing Protection type IP20 Supply voltage:... - Page 6 iPC25 operating instructions Hard drive: 2,5“ SSD 2,5“ HDD 500GB 256GB MLC/MTPF 2mill. Std. Operating system: Windows 7 Embedded standard 64bit Connections: 1 x DVI-I, 1xDisplayPort external 1 x PS/2 keyboard, 1 x PS/2 mouse 5 x USB 2.0 2 x LAN 1GBit 2 x serial Port RS 232 1 x Sub-D9-pin connection for iBP10 / iBP17 / iOP-19-TFT...
-
Page 7: Interfaces Ipc25 - F
Interfaces iPC25 - F No. Interface DVI-I connection, optional adapter DVI-I available on VGA RS 232 connection Serial interface RS232 –COM1 + COM2 LAN connection 2x RJ45 socket for network USB interfaces 4 x USB 2.0 interfaces for the connection of peripherals... - Page 8 iPC25 operating instructions SubD-9-pin socket for connection iBP10 / iBP17 / iOP-19-TFT only for cabinet mounting Description Description PWR BTN + Connection for Power key + PWR BTN GND Connection for Power key GND PWR LED +5VDC Connection for power indicator LED + PWR LED GND Connection for power indicator LED GND HDD LED +5VDC...
-
Page 9: Assembly And Start-Up
iPC25 operating instructions 3 Assembly and start-up Installation dimensions Scale drawing iPC25- F Make sure that there is always sufficient clearance for the air circulation on the ventilation slots of the iPC. Failure to observe this measure will result in overheating and possible defects in the control computer. -
Page 10: Switching On The Control Unit
iPC25 operating instructions Switching on the control unit The control unit is switched on via the contacts of the sub-D9-pin socket connection in the slot of the iPC (see chapter 2.2). When a 12V DC supply voltage is applied, the computer can also power up the operating system independently. -
Page 11: Recovering The Operating System Windows® Embedded Standard 7
iPC25 operating instructions 4 Recovering the operating system Windows® Embedded Standard 7 Important information 1) To restore the Windows® Embedded operating system Standard 7 of your control computer, you need the USB Recovery Stick supplied. This data carrier contains an image of the operating system of your installed control computer in the delivery state. -
Page 12: Maintenance And Repair
iPC25 operating instructions 4.2 Performing system recovery 1) After you have set the boot medium or the boot- sequence, start the computer again. 2) If the USB stick does the booting, a "Blue" cube is displayed on the screen and below this a rotating circle ". 3) After loading the operating system, a command line starts and then the Windows®... -
Page 13: Eg-Konformitätserklärung
6 EG-Konformitätserklärung EC - Declaration of Conformity Der Hersteller The manufacturer isel Germany AG Bürgermeister-Ebert-Str. 40 D-36124 Eichenzell erklärt hiermit, dass folgendes Produkt hereby declares that the following product Geräteart: Industrie PC Device: industrial PC Typ: iPC25-F... -
Page 14: Important Notice
___________________________ Werner Kister, Vorstand / managing board IMPORTANT NOTICE! If there are problems with ISEL Germany AG computers, please always first re-install the operating system with the help of the recovery USB- Stick supplied and matching the serial number. „...
Need help?
Do you have a question about the iPC25 - F and is the answer not in the manual?
Questions and answers