Table of Contents
Advertisement
Quick Links
903-CIS0206-C2
Installation instruction
1.2m Antenna
LEAX Arkivator Telecom disclaims any liability for the results of improper or unsafe installation, inspection, maintenance, or
removal practices.
Torsgatan 5B
SE-411 04 GÖTEBORG
SWEDEN
Telephone: +46 31 386 11 00
customer.lat@leax.com
www.leax.com
Advertisement
Table of Contents
Summary of Contents for LEAX 1.2m Antenna
- Page 1 903-CIS0206-C2 Installation instruction 1.2m Antenna LEAX Arkivator Telecom disclaims any liability for the results of improper or unsafe installation, inspection, maintenance, or removal practices. Torsgatan 5B Telephone: +46 31 386 11 00 SE-411 04 GÖTEBORG customer.lat@leax.com SWEDEN www.leax.com...
-
Page 2: Tools Required
Tools required Allen key 6mm; for M8. Combination wrenches (ring/open jaw) for Hex 13, 15 & 16mm; for M8 and M10. Socket wrench and sockets for Hex 13, 15 & 16mm; for M8 and M10. Tool for torque levels; 17Nm, 24Nm and 49Nm. ... -
Page 3: Step 1 - Support Brackets
Assembly Step 1 – Support brackets Mount Antenna support bracket ( 1 ) using 5pcs M10x35 screw ( 2 ). Tighten screws to torque of 49Nm ± 5%. Mount Strut support bracket ( 3 ) using 3pcs M10x25 screws / 3pcs Spring washer M10 / 3pcs Washers M10 ( 4 ). Tighten screws to torque of 49Nm ±... - Page 4 Step 2 – Radio unique Installation For assembling of radio interface; see radio unique installation instruction. Step 3 – Antenna support (Following steps/pictures describe a right side installation, see “Installation: Left or Right side installation” on page 6). Mount 1pcs M8x16 screw ( 5 ) to Antenna support bracket ( 1 ). Tighten screw to torque of 17Nm ± 5%. Mount Pivot bracket ( 6 ) to Antenna support bracket ( 1 ) using 1pcs M10x40 screw ( 7 ), 1pcs M10x35 screw ( 8 ) and 1pcs M10x30 screw ( 9 ).
- Page 5 Step 4 – Strut mount Secure 2pcs Clamp bracket ( 16 ) to pipe or L-section structure using 2pcs M10 Rod ( 17 ) and 4*2pcs M10 nut / 4*1pcs Washer M10 ( 18 ). Tighten nuts to torque of 49Nm ± 5%. Alternative bracket orientation Tower pipe compatibility: Ø50- Ø115mm, Tower L-section compatibility: L40x40- L110x110mm...
-
Page 6: Antenna Installation
Installation Left or Right side installation For a left side installation, switch place on support brackets, see “Assembly: Step 1 – Support brackets”. This can be done at any time, during Assembly (Step 1-4). Right side installation Left side installation Antenna installation Hoist and secure antenna to pipe (Ø90- Ø120mm) using 2pcs Clamp bracket ( 1 ) and 4pcs M10 flange nut ( 2 ). - Page 7 Mount the Strut attachment bracket ( 10 ) to one of the four corners of the Clamp brackets ( 11 ) using 1pcs M10x30 screw / 1pcs Washer M10 ( 12 ) and 1pcs M10 nut / 1pcs Spring washer M10 / 1pcs washer M10 ( 13 ). Fit screw finger tight. Attach and secure Side strut ( 7 ) to Strut attachment bracket ( 10 ) using 1pcs M8 U-bolt ( 14 ) and 2*2pcs M8 nut / 2*1pcs Washer M8 ( 15 ).
-
Page 8: Antenna Alignment
Antenna alignment Elevation adjustment Ensure 3pcs M10 screw ( 1 ) are slightly loose. Rotate Elevation screw to adjust direction ± 15°. On completion tighten screws to torque of 49Nm ± 5%. Loosen, do not remove. Elevation screw Azimuth adjustment Ensure 5pcs M10 nut ( 2 ) ( 3 ) and 2pcs M10 screw ( 4 ) are slightly loose.