Subscribe to Our Youtube Channel
Summary of Contents for Wurlitzer International L
- Page 1 International L 1,- / 2,- INTERNATIONAL L INTERNATIONAL L Operating Instructions...
-
Page 3: Table Of Contents
Reset of a l l button/column allocations in service program 09 ......28 INTERNATIONAL L – Edition: 17.02.2006... - Page 4 Overall resetting of counters - service program 04, button 8 ......47 INTERNATIONAL L – Edition:17.02.2006...
- Page 5 Overview EPROM letter codes........77 INTERNATIONAL L – Edition: 17.02.2006...
- Page 6 Filling Plan International L ........
-
Page 7: Description Of The Vending Machine
NOTE: If you are interested in optional equipment, please contact your distributor of Deutsche Wurlitzer GmbH machines. Accessories and Assemblies for Conversion Printer for statistical data Safe cash box Tobacco columns Long dividers to convert short columns to long columns International L – edition: 17.02.2006... -
Page 8: Dimensions, Weight And Capacity
! & " " " " ! " " " # 625 mm/24.4 in 617 mm/24.1 in (L) 705 mm/27.5 in International L weight (net) 140 kg/308.6 lbs selections 27 to 35 max. capacity International L – edition: 17.02.2006... -
Page 9: Unpacking, Transport And Installation
An extra fuse (T3.15amps) is placed in the bag in the cash box. Adjusting divider for converting a column The adjusting divider for a short column (1x) is placed in a bag in the cash box of the vending machine. International L – edition: 17.02.2006... -
Page 10: Installation Of The Vending Machine
Open the inner door by pulling the red handle. Insert the brand labels into the transparent films corresponding different products. Close the inner door and the door of the vending machine. " The insertion of brand and price labels is completed. International L – edition: 17.02.2006... -
Page 11: Exchange Of The Picture Display
The vending machine is delivered with a standard picture. It is easy to replace it by another. NOTE: You would like to change the picture? Deutsche Wurlitzer GmbH or your distributor offers a selection of pictures. In order to exchange the picture, follow the steps below: Open the door of the vending machine. -
Page 12: Conversion Of The Product Columns
Conversion of the Product Columns The product columns 22 to 37 (see figure below) can be converted to long or short columns. To do so, special dividers are necessary – contact Deutsche Wurlitzer GmbH or your distributor if necessary. Ensure the correct functioning of the vending machine! If you change the number of product columns between the columns 22 to 37, you have to adjust the assignment of product selection and motor again. -
Page 13: Adjusting Product Columns
12. Update the filling plan of the vending machine, see page 13. Close the door. " The adjustment of the width of the product column is completed and the vending machine is ready for operation again. International L – edition: 17.02.2006... -
Page 14: Adjusting The Depth Of A Short Product Column - Length Of Packs 75 Mm/2.9 Inches To 105 Mm/4.1 Inches
Setting for: long packs: without adapter rail, install adjusting lever in rear position standard packs: without adapter rail, install adjusting lever in middle position short packs: install adapter rail, install adjusting lever in front position International L – edition: 17.02.2006... -
Page 15: Adjusting The Clearance Height Of A Product Column
26 mm/1.0 in to motor installed in lower position square for reducing the clearance height 32 mm/1.3 in 32 mm/1.3 in to motor installed in lower position without square for reducing the clearance 40 mm/1.6 in height International L – edition: 17.02.2006... - Page 16 The squares for reducing the clearance reduce the clearance of the corresponding product column by 8 mm/0.3 inches – if they are screwed to the adjusting levers. The accessories contain the square for reducing the clearance (1 x). International L – edition: 17.02.2006...
-
Page 17: Conversion Long Column/Short Column
If you want to extend your product selections, you can convert the long columns of the vending machine into two short columns respectively. To do so, special dividers and additional motors are needed. NOTE: Deutsche Wurlitzer GmbH or your distributor offer dividers for short columns and motors. Part numbers:... -
Page 18: Taking The Vending Machine Into Operation
IMPORTANT! Perform a motor test, see page Programme the vend prices, see page 29. Perform some test vends with money when the door is open. Close the machine door. " The machine is now ready to work. International L – edition: 17.02.2006... -
Page 19: Programming Of The Machine
(_ = space sign in reality). NOTE: You can freely programme the LCD display. Therefore the following explanations only refer to the service program numbers and data, which are displayed either through preset by factory or through empty text memory. International L – edition: 17.02.2006... -
Page 20: The Service Programs (Overview)
"IN OPERATION" and "MACHINE ACCEPTS 0.05 - 2.00 EURO" or, in case the change giver tubes are empty, "PLEASE INSERT EXACT MONEY" and "MACHINE ACCEPTS 0.05 - 0.50 EURO". Second possibility: Wait for some 60 seconds after that the machine automatically reverts to standard vending mode. International L – edition: 17.02.2006... -
Page 21: Programming Of Vend Prices
(old) price, e.g. 1.90 EURO Press key P once, display shows SELECTION: =0150 Continue the same manner: enter the selection number(s) SELECTION: and press key P once. The display always shows, e.g. =0150 1.50 EURO. International L – edition: 17.02.2006... - Page 22 When price programming is completed leave the service program (see page 20). Price check: Press any selection number, the current vending price flashes for a few seconds. Press button C to proceed to the next compartment.Repeat as many times as needed. International L – edition: 17.02.2006...
-
Page 23: Machine Test - Service Program 07
If the motor test does not run the 'spiral single shut down' mode in service pro- gram 15, button 9 may not be programmed, see page 74 and page 77. Press key C to complete the job. Press button 7:Leave the service program (see page 20). International L – edition: 17.02.2006... -
Page 24: Optional Button/Column Allocation - Service Program 09
Press button P - hold it - display goes dark, enter the fig- 2020 ures 2 0 2 0, display shows Press button C, display shows " Finally press button S until display shows “Ready”. International L – edition: 17.02.2006... -
Page 25: One Selection Drives Different Columns Alternately
1 0 1 2. Display shows " Finally press button S until display shows “Ready”. 8.1.3 Several selections driving one column Example: If one of selections 11, 12 or 13 is made, always column no. 13 delivers. selections column International L – edition: 17.02.2006... -
Page 26: Several Selections Driving Alternately Same Number Of Columns, I.e. Columns Deliver Evenly No Matter Which Column Was Selected
Enter selection 14, display shows 1414 Press button P - hold it - display goes dark and enter the 1418 figures 1 4 1 8, display shows Enter selection 15, display shows 1515 Press button P, display shows 1418 International L – edition: 17.02.2006... -
Page 27: Reset Of This Button/Column Allocation Shown In Example
Press button P - hold it - display goes dark. Enter the fig- 1515 ures 1 5 1 5, display shows Press button C, display shows Continue the same manner up to selection 18. " Finally press button S until display shows “Ready”. International L – edition: 17.02.2006... -
Page 28: Reset Of A L L Button/Column Allocations In Service Program 09
Press button P - hold it - display goes dark. Enter 4 times 9999 figure 9, display shows first 1111 then Press button C, display shows " Finally press button S until display shows “Ready”. International L – edition: 17.02.2006... -
Page 29: Operation With Mdb
02 =2 04 then SELECTION: One coin is delivered out of each tube. If you press selection button 2 again the three coin pushers make a new delivery. Finally leave the service program (see page 20). International L – edition: 17.02.2006... -
Page 30: Emptying Single Tubes - Service Program 07
For alteration press button P, hold it, and enter the desired SELECTION: change amount in four digits, for example sum to be 10.00 =1000 EURO enter 1 0 0 0. Finally leave the service program (see page 20). International L – edition: 17.02.2006... -
Page 31: Vend Mode - Service Program 10, Button R
90 = Multivend, but the customer might lose change if message "PLEASE INSERT EXACT MONEY " or "MACHINE AC- CEPTS 0.05 - 0.50 EURO" appears on the display be- cause return tubes have not enough change. International L – edition: 17.02.2006... -
Page 32: Coin Acceptance Options - Cancellation Of Individual Coins - Service Program 12
80) should be displayed now. 01 = NOTE: If you carry out a data block transfer in service program 11, button 1 (input 9999), the changed acceptance options are cancelled and the standard settings are again in force. International L – edition: 17.02.2006... -
Page 33: Test Credit - Service Program 11
Enter the desired number (e.g. 99) using two digits, display SELECTION: shows Any settings between 00 and 99 are possible. One more coin than the number programmed will always be accepted. Finally leave the service program (see page 20). International L – edition: 17.02.2006... -
Page 34: Data Block" Transfer - Service Program 11, Button 1
10.00 EURO. Alteration: Press button P - hold it - display shows SELECTION: 09 = Enter the new basic value in 4 digits, i.e. 0500 for 5.00 EURO, SELECTION: display shows =2000 Release button P. International L – edition: 17.02.2006... -
Page 35: Programming Of Bill Options - Service Program 12, Button 9
Press button P - hold it - display shows SELECTION: 06 = Enter new number of bills to be accepted (-1), i.e. 09 for 10 bills, SELECTION: in 2 digits, display shows Release button P. Finally leave the service program (see page 20). International L – edition: 17.02.2006... -
Page 36: Mdb Coin System - Statistics
As an example we give you the sum of 9352.70 EURO. Display 1 (higher value 9300 EURO) Display 2 (lower value 52.70 EURO) SELECTION: SELECTION: 01 =0093 02 =5270 International L – edition: 17.02.2006... -
Page 37: Individual Counter Reset
0000. Complete the process by pressing key C. Then proceed to the next counter. Please notice that the statistics counters take two displays, one for the lower and the other for the higher figures, and that the displays have to be individually reset. International L – edition: 17.02.2006... -
Page 38: Reset Of All Counters - Service Program 04, Button 8
(see chapt. 20 on page 67). Test vend: When you wish to make a test vend, push button "Credit" of the IVC control unit. The test vend has no effect on the vend counters. test vend International L – edition: 17.02.2006... -
Page 39: Operation With Coin Systems According To Bdv Standard
SELECTION: One coin is delivered out of each tube. If you operate selection button 2 again, the coin pushers deliver another coin out of each tube. Finally leave the service program (see page 20). International L – edition: 17.02.2006... -
Page 40: Dispense Of Single Tubes - Service Program 07
Press button 1, display shows (factory preset) SELECTION: 01 =9000 The maximum insertion sum is set at 90.00 EURO. If you want to change that, press key P, hold it and enter the new desired maximum insertion in four digits. International L – edition: 17.02.2006... -
Page 41: Bdv Vend Mode - Service Program 11, Button 7
Finally leave the service program (see page 20). 12.8 Test vend If you press the "Credit" button of the IVC control unit, you can make one free-of-charge vend which has no effect on the counters. International L – edition: 17.02.2006... -
Page 42: Disabling Single Coins - Service Program 11, Button 5
Finally leave the service program (see page 20). NOTE: Applying button 6 in service program 11 you can disable coins in extended coin stock system (coin channels 8 to 14, respectively coins H to N). International L – edition: 17.02.2006... -
Page 43: Programming Those Coins To Be Disabled Immediately After The Display Shows "Please
0 0 4 8 =0048 How to check: Press selection button C, display shows service program SELECTION: Press selection button 3 which displays the new option, e.g. SELECTION: 03 = Finally leave the service program (see page 20). International L – edition: 17.02.2006... -
Page 44: Modifying Responses To "Tube Empty" Messages - Service Program 11, Button 2
2 - Empty message appears when the actual number of coins in tube A or B and C is less than 15. Programming: Press key P - hold it and enter desired option. NOTE: With a 4-tube-changer the tube D will not be affected. International L – edition: 17.02.2006... -
Page 45: Vend Statistics With Coin Systems Acc. To Bdv Standard
As an example we give you the sum of 9352.70 EURO. Display 2 (lower value 52.70 EURO) Display 1 (higher value 9300 EURO) SELECTION: SELECTION: 01 =0093 02 =5270 International L – edition: 17.02.2006... -
Page 46: Individual Resetting Of Counters
P to reset the counter. The display is set to 0000. To complete the job, press key C and proceed to the next issue. Please remember that the statistics counters are displayed in two parts, which means you have to reset both, the higher-value display and the lower-value display, individually. International L – edition: 17.02.2006... -
Page 47: Overall Resetting Of Counters - Service Program 04, Button 8
6, button 7/8 are not reset. The data has to be reset separately. The reset of the counter for current supply interruptions is described in see chapt. 14.1 on page 48. Finally leave the service program (see page 20). International L – edition: 17.02.2006... -
Page 48: Operating Information
Operating time - service program 15 (NOT resetable) The hours of service can be displayed in 8 digits using service program 15, buttons 7 and 8. Button 7 displays the higher figures and button 8 the lower figures. International L – edition: 17.02.2006... -
Page 49: The Lcd Display
16 new lines per message. Button 7 Calls up the preceding message (starting at 0). The last message is numbered 49. Button 8 Calls up the next message. After calling the last one, message 0 appears again. International L – edition: 17.02.2006... - Page 50 1 or 2 pressed, the function is automatically repeated. How to enter blank characters: Keep pressing button 9 (auto repeat) until an exclamation mark (!) is displayed in the cursor field. First press button 1 and then key C. International L – edition: 17.02.2006...
-
Page 51: Messages
However at this time only the messages 00 - 22 and 31 - 46 will be used. Example: Message 00: indicates optional readiness in stand-by mode ("MACHINE_ACCEPTS_0.05_-_2.00_EURO") Message 12: indicates a fault. Possible messages shown starting page 54. International L – edition: 17.02.2006... -
Page 52: Message Display In The Editor
The place holder involved can only be determined when it is in the cursor field. ATTENTION! Actual data about credits or error messages etc. can only be displayed when place holders are programmed. International L – edition: 17.02.2006... -
Page 53: Description Of The Used Place Holders
Bill acceptance 4 figures + decimal point Data display (e.g. selection options) Data display (e.g. statistics) Data display 4 figures + decimal point Data display counter 8 figures Data display 8 figures + decimal point International L – edition: 17.02.2006... -
Page 54: What The Messages Tell You
Waiter key activated D2=NUMBER D9=COUNTER D2, D9 Operating voltage is too low Test credit Common error (user error) Credit display with an empty change giver Insertion of exact money (empty and vend) 23..30 Reserved 31..45 Help functions to service programs International L – edition: 17.02.2006... -
Page 55: Suggestions To Programme
SELECTION: W2__=_D4___ PRINTING! ERROR_CODE:_E2_ ERROR_! Error warning WAITER_KEY Waiter key D2__ _D9________ Cigarette machines only! LOW_POWER_INPUT TEST_CREDIT: K5_____EURO WRONG_SELECTION! NO_CHANGE Credit display, if change giver empty K5_____EURO INSERT_EXACT Exact money only (empty and vend) MONEY_P5_____EURO International L – edition: 17.02.2006... - Page 56 S2_VEND_OPTIONS Service program 10 S2_COIN_CHANNEL Service program 11 _SETTING S2_COIN OPTIONS Service program 12 S2_CHANGER_CHAN. Service program 13 _SETTING S2_CHANGER Service program 14 _OPTIONS S2_MAIN Service program 15 _CONFIGURATION S2_WAITER Service program 16 _KEY International L – edition: 17.02.2006...
-
Page 57: Programming Example
After the last data input the display should show 00:01-14=ON> N< The 2 space characters on the right text side don't have to be programmed. Press key S once to exit the service programme, message "IN OPERATION" is displayed. International L – edition: 17.02.2006... -
Page 58: How To Format Text Memory - Service Program 15
It may be useful to erase the text memory of a machine with a LED display. For example, if the IVC control unit has been replaced. Those messages that are not necessary for a LED display, may lengthen the computing time of the IVC control unit, which can cause a flickering display. International L – edition: 17.02.2006... -
Page 59: How To Programme The Text Memory Applying Pc
With the option 'change text' on the LCD display it is possible to transmit only display messages from other control units or files to further control units. So you can change the language, without influenc- ing to configuration. International L – edition: 17.02.2006... -
Page 60: Statistic Print Outs
Press selection button 2 and release it. To programme keep button P pressed and enter the configuration number 3708 via the selection buttons. NOTE: The LED ‘SET’ has to light for printing the data! If not press button ‘SEL’ once. International L – edition: 17.02.2006... -
Page 61: Print-Out Of Statistics
Keep pressing key S of the programming panel until the display shows 08 „PRICE PROGRAM- MING“. Press button “Print” of the IVC-unit. The print-out process starts (display shows “PRINTING”). After printing press button S several times until „In Operation“ is displayed (see page 20). International L – edition: 17.02.2006... -
Page 62: Statistic Print Out Mdb
TOTAL :0146 data are NO=COIN: resetable ============ 01=0010:0005 02=0050:0002 income number of accepted coins per sort 03=0100:0003 04=0200:0003 05=0500:0003 06=0000:0000 07=0000:0000 08=0000:0000 number of accepted bank notes S =1000:0001 NO=COIN: OUT ============ 01=0010:0010 02=0050:0000 International L – edition: 17.02.2006... - Page 63 MACHINE:0000 safety number SAFETY :0525 resetable error code ERROR resetable number of ON and OFF switches 8replacement of fuses too) OFF-ON :0000 NOT resetable total operation time in hours 00005493 International L – edition: 17.02.2006...
-
Page 64: Statistic Print Out Nri Simplex 5 Or Executive
AMT:00001000 -TOTAL-SUMS- ============ total sales of machine VPR:00602218 total income (cash + change) INC:00002550 total number of returned coins after vend procedure RET:00000300 NOT resetable amount of money in change giver AMT:00001800 International L – edition: 17.02.2006... -
Page 65: Statistic Print Out Bdv Standard
2 (&V*P = Vend*Price) &V*P00008220 number of selections number of vends price per selection 60:0019 0050 61:0012 0080 62:0006 0120 63:0004 0120 64:0000 0100 65:0015 0220 66:0020 0090 67:0018 0080 68:0022 0070 International L – edition: 17.02.2006... - Page 66 DIV:00000000 MIS:00000000 MIN:00000000 machine no. (service program 05, button 9) MACHINE:0000 safety number SAFETY :0525 displayed error code during printout ERROR number of ON and OFF switches OFF-ON :0000 total operation time in hours 00005493 International L – edition: 17.02.2006...
-
Page 67: Initialisation Of An Ivc Unit After Replacement
Press button D, number 0 outside is blinking SELECTION: With button + you can change the blinking 0 to a number be- 01 =0000 tween 1 and 9. In this case (7620) the character stays 0. International L – edition: 17.02.2006... - Page 68 BDV standard with vend light gate 3180 3107 9000 0070 electronic coin acceptor (ECA) and 5 tube changer 3660 3107 0000 0060 electronic coin acceptor (ECA) only (exact money) 3460 3107 0000 0060 CCI-System 3480 3107 1000 0060 International L – edition: 17.02.2006...
-
Page 69: For Machines With Mdb - Carry Out 'Data Block Transfer' Service Program 11, Button 1
Enter new number of coins (e.g. 99), display shows SELECTION: Possible number of coins is between 00 and 99. Always one more coin than programmed will be accepted. Finally leave the service program (see page 20). International L – edition: 17.02.2006... -
Page 70: Machines With Coin System Acording To Bdv Standard
To alter the sum press key P - hold it - and enter new sum in SELECTION: four digits, e.g. 10.00 EURO, enter 1 0 0 0. Display is =1000 Finally leave the service program (see page 20). International L – edition: 17.02.2006... -
Page 71: Machine Specification Self-Test
The cur- rent tested compartment is shown in the last two characters. SELECTION: 07 =7 89 Press key C. Finally leave the service program (see page 20). International L – edition: 17.02.2006... -
Page 72: Service Programs (In Tabular Form)
* Motor test of each spiral Access to service programs 11 - 17 P + 8 Price programming selection buttons reset Max. change * return button Free button column allocation only for cigarette machines! International L – edition: 17.02.2006... - Page 73 Change giver options: * selection buttons 1 - 5 programme 00 = tube exists 80 = tube not exists Max. bill acceptance (piece + 1) selection button 6 programme selection button 7 programme Max. coin acceptance (piece +1) International L – edition: 17.02.2006...
- Page 74 15 on page 49 ATTENTION! The programming options marked with an asterisk * only apply to MDB systems. For machines with Executive coin systems these options have to be programmed on the coin system it- self. International L – edition: 17.02.2006...
-
Page 75: Coin Systems According To Bdv Standard
Max. change return button Free button column allocation only for cigarette machines! Vend options: selection buttons programme 00 = normal 01 = free vend 04 = parallel 08 = alternate 80 = disable International L – edition: 17.02.2006... - Page 76 1 - 5 programme 00 = tube exists 80 = tube does not exist, disabled Max. bill acceptance (piece + 1) selection button 6 programme Max. bill acceptance (piece + 1) selection button 7 programme International L – edition: 17.02.2006...
-
Page 77: Overview Eprom Letter Codes
NRI Simplex 0, without HC11 only, MDB ELEER Empty lights Card system MDB, with HC11 only and MDB, no BDV ! MDBBIL Bank note acceptor MDB Protokoll, only HC11 and MDB BDV or Executive coin system International L – edition: 17.02.2006... -
Page 78: Error Messages
An extension cable to facilitate the finding of any fault at the spiral motors of the trays is available un- der part-no. 0005057. The cable enables you to check any tray outside the machine or to put a new tray into operation. International L – edition: 17.02.2006... -
Page 79: The State 'Out Of Order
Exit the service program whereby the display shows: "00.00". Message 0 deleted. Enter the new text messages (see chapt. 15.9 on page 57) or programme with software IVC-Pro- grammer (see chapt. 15.11 on page 59). International L – edition: 17.02.2006... -
Page 80: List Of Error
Return signal from the cash flap too long. Cash flap open more than 5s or jammed, contact between flaps not opening after return signal. Notice: Error codes 11 to 14 only apply to machines with a Deutsche Wurlitzer GmbH escrow. In case they are displayed in machines without escrow, you have to check configuration. - Page 81 Change the coin validator. Notice: Error codes 40 to 48 mainly apply to machines with a Deutsche Wurlitzer GmbH escrow unit. In case this error codes appear in machines with MDB systems, you have to carry out data block transfer (see chapt.
- Page 82 Valid for all coin systems. kely due to a defective communication cable between the coin validator/coin sys- tem and the IVC control unit, or a re-pro- gramming has to be carried out. MDB checksum fault. International L – edition: 17.02.2006...
-
Page 83: Technical Data
IVC2 control unit by means of the programming kit. serial number of the vending machine Give this number when you contact the service of Deutsche Wurlitzer GmbH. The engineers are able to specify your vending machine exactly by means of this number. 24.2... -
Page 84: Technical Appendix
Column No. Selection Brand Price Middle Columns Brand Name Selection Column No. Selection Brand Price Middle Columns Brand Name Selection Column No. Selection Brand Price Door Columns Brand Name Selection Column No. Selection Brand Price International L – edition: 17.02.2006... - Page 85 25.2 Connecting Diagram Hinterschacht/rear column Vorderschacht/front column Mittelschacht lang/ middle column long Mittelschacht kurz/middle column short International L – edition:: 17.02.2006...
-
Page 86: Connecting Diagram
Limits an methods of measurement of radio interference characteristics of information technology equipment Sécurité des appareils electrodomestiques et analogues Unterschrift/Signature/ Signature Gedruckter Name/Print Jürgen Obermeier name/nom Position/Position/Position Chief Engineer/Technischer Leiter/Directeur Technique Datum/Date/Date 2. Januar 1995/2. January 1995/2. Janvier 1995 International L – edition: 17.02.2006... - Page 88 Germany Deutsche Wurlitzer GmbH Wurlitzerstraße 6 D-32609 Hüllhorst Tel.: +49(0) 57 44 - 941-0 Fax: +49(0) 57 44 - 941 220 Email: contact@deutsche-wurlitzer.de Part no.: 0049096 - revision 4602 Wurlitzer® Registered Trademark of The Wurlitzer Company...
Need help?
Do you have a question about the International L and is the answer not in the manual?
Questions and answers
how to change cigarette prices the program is not used
To change cigarette prices on a Wurlitzer International L:
1. Press key S to access service program 08 (PRICE PROGRAMMING).
2. Enter the desired compartment (selection) number (e.g., SELECTION: 10).
3. The current price will be displayed (e.g., 10 = 0050 for €0.50).
4. To change the price, press and hold key P.
5. Enter the new price using four digits (e.g., 0110 for €1.10).
6. To move to the next selection or correct an input, press key C.
7. Repeat for other compartments as needed.
This answer is automatically generated
Blocked sistem
If a compartment is blocked on a Wurlitzer International L, the following troubleshooting steps apply:
1. Blocked Compartment: The control unit automatically blocks a compartment if there is an issue, preventing purchases from that compartment. Other compartments remain usable.
2. Tray Check: Verify that all trays are properly inserted, as improper tray placement may cause blockages.
3. Error Codes:
- Codes 02 to 09: These are warnings and do not significantly affect machine function.
- Codes 11 to 14: These relate to return or cash flap problems (e.g., jammed flaps or contact issues). If the machine does not use a Deutsche Wurlitzer GmbH escrow, check the machine configuration.
No additional error codes or procedures for general system blockage are provided in the context.
This answer is automatically generated