Subscribe to Our Youtube Channel
Summary of Contents for Sherpa STWT52
- Page 1 OPERATOR’S MANUAL STWT52 WHEELED TRIMMER IMPORTANT! IT IS ESSENTIAL THAT YOU READ THE INSTRUCTIONS IN THIS MANUAL BEFORE ASSEMBLING, OPERATING AND MAINTAINING THIS MACHINE.
- Page 2 Sherpa Tools Ltd. STWT52 WHEELED TRIMMER If you experience any problems with this product, please do not return to the store. Contact Sherpa Tools direct on our UK helpline. UK Helpline: 01522 283 020 www.sherpatools.co.uk June 2015...
-
Page 3: Safety Information
SAFETY INFORMATION SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. -
Page 4: Safe Operation
3. Do not wear loose clothing, be answered herein, contact and in a safe manner. jewellery, short trousers, Sherpa Tools. sandals, or go barefoot. Do not 2. When planning your work wear anything which might be 3. Always be sure to include... -
Page 5: Before Starting The Engine
BEFORE STARTING THE STARTING THE ENGINE the width of your shoulders) so ENGINE that your weight is distributed 1. Keep bystanders and evenly across both legs, and 1. The area within a perimeter animals at least 50feet (15m) always be sure to maintain of 50 feet (15m) of the person away from the operating a steady, even posture while... -
Page 6: Handling Fuel
MAINTENANCE refuelling. 1. In order to maintain your 5. After refuelling, screw the product in proper working order, fuel cap back tightly onto the perform the maintenance and fuel tank and then carry the checking operations described unit to a spot 10feet (3m) or in the manual at regular more away from where it was intervals. - Page 7 ASSEMBLY 2. INSTALLING SHAFT Line shaft (6) up with entry point at bottom of engine (7). Insert and push irmly into place. Ensure the bottom end of the shaft is pointing straight down in preparation of attaching protection shield and cutting head.
- Page 8 2 stroke oil in this engine and allow it cool before machine with an ethanol shield. refuelling the unit. Sherpa recommends use of • Keep open lames away from B3C oil in the wheeled trimmer, the area where fuel is handled when using this product you or stored.
-
Page 9: Operation
OPERATION STARTING ENGINE 4. Push the primer bulb pump open the choke and repeat ive or six times. (OP1) pulling the rope, or remove the spark plug and dry it. 5. While pulling the throttle The cutting head will start trigger all the way in, push the rotating upon the engine starts. -
Page 10: Trimming Grass And Weeds
LINE HEAD USAGE your balance or control of the the unit on your right side. unit. Adjust the harness length so that the cutting head may 5. Try to control the cutting become parallel to the ground. motion with the hip rather than placing the full workload on the 1. -
Page 11: Maintenance
MAINTENANCE Maintenance, replacement, or AIR FILTER The air ilter, if clogged, repair of the emission control device and systems may be will reduce the engine performed by any non-road performance. Monthly check and clean the ilter element engine repair establishment or individual. -
Page 12: Tightening Torque
• Check the intake air cooling grease has worked its way in vent and the area around the between the clutch lining and cylinder cooling ins after every Note that using any spark plugs drum, and if it has wiped it other than those designated 25 hours of use for blockage, away using oil-free, lead-free... -
Page 13: Engine Parts Diagram
1E44 -5汽油机部件分解图 ENGINE PARTS DIAGRAM 1E44 -5 GASOLINE ENGINE E XPLODED VIEW... - Page 14 TRIMMER PARTS DIAGRAM Trimmer Head Head Spacer Head Bolts Protection Ring Protection Guard Geared Shaft Engine & Chassis Winged Screw 10. Lower Handle 11. Upper Handle 12. Throttle Cable...
-
Page 15: Troubleshooting
TROUBLESHOOTING PROBLEM CAUSE CORRECTION Will not start 1. Out of fuel 1. Fill fuel tank 2. Engine not choked properly 2. See TO START ENGINE instructions 3.Engine looded 3. Wait several minutes before trying again 4. Dirty air ilter 4. Clean or replace air ilter 5. - Page 16 CONTACT Sherpa Tools Ltd. STWT52 WHEELED TRIMMER If you experience any problems with this product, please do not return to the store. Contact Sherpa Tools direct on our UK helpline. UK Helpline: 01522 283 020 www.sherpatools.co.uk June 2015...
Need help?
Do you have a question about the STWT52 and is the answer not in the manual?
Questions and answers